GLOBAL OUTDOORS FP51005 User guide

INSTALLER: Leave this manual with
the appliance.
CONSUMER: Retain this manual for
future reference.
Do not store or use gasoline or other
ammable vapors or liquids in the vicinity
of this or any other appliance.
An LP-cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
Installation and service must be performed
by a qualied installer, service agency, or
the gas supplier.
If the information in this manual is not
followed exactly, a re or explosion may
result causing property damage, personal
injury, or loss of life.
1. Shut o gas to the appliance.
2. Extinguish any open ame.
3. If odor continues, leave the area immediately.
4. After leaving the area, call your gas supplier or
re department.
Failure to follow these instructions could result in
re or explosion, which could cause property
damage, personal injury, or death.
ITM. / ART.
MODEL #: FP51005

WARNING Read and follow all instructions and warnings in this Owner’s Manual thoroughly
before installing, operating, or servicing this Fire Pit.
Improper installation, use, maintenance, adjustment or storage can cause re or
explosion, resulting in serious injury or property damage.
prepare for use:
Keep away from Combustible/Flammable Items
• Do not put any other replace cover or anything ammable on or beneath Fire Pit.
• Combustible materials should never be within 1.83 m/6 ft of the top, 1.22 m/4 ft of back or sides of Fire Pit.
• For use on noncombustible oor material only.
• Keep Fire Pit area clear and free from combustible materials, gasoline, and other ammable vapors and liquids.
Inspect for leaks, wear and damage
• Open Door and check for gas leaks before use - See page 7, Step #8 for instructions on how to check for gas leaks.
• Inspect burner and hose before use - Replace if there is evidence of excessive abrasion, wear, or damage.
• Inspect hose before each use. Hose assembly must be replaced prior to use if there is evidence of excessive abrasion or wear or if
hose is damaged. Use a manufacturer-specied replacement hose only.
Prepare area, ensure proper use of Fire Pit Cover
• Make sure ventilation openings on sides of Fire Pit (BODY) are open and clear of debris.
• Do not lay Nylon Fire Pit Cover over Fire Pit for at least 4 hours after it is turned OFF and has completely cooled down.
• Do not use Fire Pit if any part has been under water. Immediately call a qualied service technician to inspect Fire Pit and to replace
any part of the control system and any gas control that has been under water.
• Remove Nylon Fire Pit Cover from Fire Pit before operating.
when in use:
Do’s
• Use propane cylinders with the following required measurements only: 30.5 cm/12 in (diameter) x 45.7 cm/18 in (tall)
with capacity 9 kg/19.84 lbs.)
• If ame goes out while operating, turn gas valve OFF. Wait ve minutes before attempting to relight.
• Due to high surface temperatures always keep a safe distance to avoid burning or clothes catching re.
• Keep fuel supply hose away from any heated surfaces.
Don’t’s
• Never lean over the open Fire Pit or place hands or ngers on the upper portion while in use.
• Do not use Fire Pit for cooking.
• Do not burn any other materials other than what is supplied with and intended for use in Fire Pit.
• Solid fuels shall not be burned in this Fire Pit.
• Do not pour water into Fire Pit.
• Do not move Fire Pit while in operation.
• Fire Pit should never be operated by children. Children must be supervised when they are anywhere near Fire Pit.
• Do not rest feet on Fire Pit.
• Do not use Fire Pit on vehicles or boats. Always operate Fire Pit on at ground outdoors.
when not in use:
• Remove Battery from Ignitor when not using Fire Pit for an extended length of time.
• Clean battery contacts and also those of the device prior to battery installation.

prepare for use:
Keep away from Combustible/Flammable Items
• Do not put any other replace cover or anything ammable on or beneath Fire Pit.
• Combustible materials should never be within 1.83 m/6 ft of the top, 1.22 m/4 ft of back or sides of Fire Pit.
• For use on noncombustible oor material only.
• Keep Fire Pit area clear and free from combustible materials, gasoline, and other ammable vapors and liquids.
Inspect for leaks, wear and damage
• Open Door and check for gas leaks before use - See page 7, Step #8 for instructions on how to check for gas leaks.
• Inspect burner and hose before use - Replace if there is evidence of excessive abrasion, wear, or damage.
• Inspect hose before each use. Hose assembly must be replaced prior to use if there is evidence of excessive abrasion or wear or if
hose is damaged. Use a manufacturer-specied replacement hose only.
Prepare area, ensure proper use of Fire Pit Cover
• Make sure ventilation openings on sides of Fire Pit (BODY) are open and clear of debris.
• Do not lay Nylon Fire Pit Cover over Fire Pit for at least 4 hours after it is turned OFF and has completely cooled down.
• Do not use Fire Pit if any part has been under water. Immediately call a qualied service technician to inspect Fire Pit and to replace
any part of the control system and any gas control that has been under water.
• Remove Nylon Fire Pit Cover from Fire Pit before operating.
when in use:
Do’s
• Use propane cylinders with the following required measurements only: 30.5 cm/12 in (diameter) x 45.7 cm/18 in (tall)
with capacity 9 kg/19.84 lbs.)
• If ame goes out while operating, turn gas valve OFF. Wait ve minutes before attempting to relight.
• Due to high surface temperatures always keep a safe distance to avoid burning or clothes catching re.
• Keep fuel supply hose away from any heated surfaces.
Don’t’s
• Never lean over the open Fire Pit or place hands or ngers on the upper portion while in use.
• Do not use Fire Pit for cooking.
• Do not burn any other materials other than what is supplied with and intended for use in Fire Pit.
• Solid fuels shall not be burned in this Fire Pit.
• Do not pour water into Fire Pit.
• Do not move Fire Pit while in operation.
• Fire Pit should never be operated by children. Children must be supervised when they are anywhere near Fire Pit.
• Do not rest feet on Fire Pit.
• Do not use Fire Pit on vehicles or boats. Always operate Fire Pit on at ground outdoors.
when not in use:
• Remove Battery from Ignitor when not using Fire Pit for an extended length of time.
• Clean battery contacts and also those of the device prior to battery installation.
THIS PRODUCT USES PROPANE ONLY
DANGERS AND WARNINGS
3
when storing Fire Pit:
Storage of Fire Pit indoors is permissible only if the cylinder is disconnected and removed from Fire Pit. Cylinders must be stored outdoors in a well-ventilated area
out of reach of children. Disconnected cylinders must have threaded valve plugs tightly installed and must not be stored in a building, garage or any other
enclosed area.
Turn OFF control knob and close propane cylinder valve.Turn coupling nut counterclockwise by hand only—do not use tools to disconnect. Loosen cylinder
screw beneath bottom shelf, then lift propane cylinder up and out of shelf. Place dust cap on cylinder valve outlet whenever the cylinder is not in use.
WARNING! Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner's information manual
provided with this appliance. For assistance or additional information consult a qualied installer, service agency or the gas supplier.
The Propane-gas supply cylinder must be disconnected when this appliance is not in use.
Any guard or other protective device removed for servicing the appliance shall be replaced prior to operating the appliance.
Installation and repair should be done by a qualied service person. The appliance should be inspected before use and at least annually by a qualied service
person. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burners, and circulating air passageways of the
appliance are kept clean.
WARNING:This product can expose you to chemicals including byproducts of the combustion of propane, which is known to the State of California to
cause birth defects or other reproductive harm. For mor information go to www. P65Warning.ca.gov.
• Use propane cylinders with the following required measurements only: 30.5 cm/12 in (diameter) x 45.7 cm/18 in (tall)
with capacity 9 kg/19.84 lbs.)
• Max gas supply 28cm/11 in w.c. (2.74kpa)
• Only cylinder marked "propane”may be used.
• lf you see, smell or hear the hiss of escaping gas from the propane cylinder:
1. Turn o gas supply and get away from gas cylinder and Fire Pit at once.
2. Do not attempt to correct the problem yourself.
3. Call your gas supplier and/or the re department for help.
• A dented or rusty propane cylinder may be hazardous and should be cleared by your gas supplier prior to use.
• Do not attempt to disconnect gas regulator or any gas tting while Fire Pit is in operation.
• The gas pressure regulator provided with Fire Pit must be used.
• Do not use a propane cylinder with a damaged valve and any other worn out parts.
• Transport and store empty propanecylinders carefully and properly.
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns
or clothes catching re.
• Young children should be carefully supervised when they are in the area of Fire Pit.
• Clothing or other ammable materials should not be hung from Fire Pit, or placed on or near Fire Pit.
Propane-gas supply cylinder to be used must be:
• constructed and marked in accordance with the U.S. Department of
Transportation (DOT) Specications for LP-Gas Cylinders, or the Standard for
Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and
Commission, CAN/CSA-B339, as applicable;
• provided with a listed overlling prevention device; and
• provided with a cylinder connection device compatible with the
connection for the appliance.

PREPARATION FOR ASSEMBLY
PACKAGE CONTENTS AND COMPONENTS
Before beginning assembly of Fire Pit, make sure all parts are present. Compare parts with package contents list. If any part is missing or
damaged, do not attempt to assemble Fire Pit.
Estimated Assembly Time: 25 minutes
NOTE: You must follow all steps to properly assemble Fire Pit. Make sure the gas valve is turned OFF before assembling.
Do not attempt to assemble without proper tools.
Maximum amount of Fire Glass to be used is 7.5kgs (16.5 lbs).
4
PART DESCRIPTION QTY
A Fire Bowl 1
B Body 1
C Door 1
D Burner Ring (preassembled) 1
E Gas Screen (preassembled) 1
F Fire Glass 2 boxes
G Nylon Cover 1
H Battery 1
I Adjustable feet (preassembled) 4
J Control Knob (preassembled) 1
K Electric Igniter (preassembled) 1
L Lid with Handle 1
M Burning Components 1
(preassembled)
N Door knob (preassembled) 1
O Windproof glass Ass’y 1
(Accessories, consumer assembly
Step 9)

prepare for use:
Keep away from Combustible/Flammable Items
• Do not put any other replace cover or anything ammable on or beneath Fire Pit.
• Combustible materials should never be within 1.83 m/6 ft of the top, 1.22 m/4 ft of back or sides of Fire Pit.
• For use on noncombustible oor material only.
• Keep Fire Pit area clear and free from combustible materials, gasoline, and other ammable vapors and liquids.
Inspect for leaks, wear and damage
• Open Door and check for gas leaks before use - See page 7, Step #8 for instructions on how to check for gas leaks.
• Inspect burner and hose before use - Replace if there is evidence of excessive abrasion, wear, or damage.
• Inspect hose before each use. Hose assembly must be replaced prior to use if there is evidence of excessive abrasion or wear or if
hose is damaged. Use a manufacturer-specied replacement hose only.
Prepare area, ensure proper use of Fire Pit Cover
• Make sure ventilation openings on sides of Fire Pit (BODY) are open and clear of debris.
• Do not lay Nylon Fire Pit Cover over Fire Pit for at least 4 hours after it is turned OFF and has completely cooled down.
• Do not use Fire Pit if any part has been under water. Immediately call a qualied service technician to inspect Fire Pit and to replace
any part of the control system and any gas control that has been under water.
• Remove Nylon Fire Pit Cover from Fire Pit before operating.
when in use:
Do’s
• Use propane cylinders with the following required measurements only: 30.5 cm/12 in (diameter) x 45.7 cm/18 in (tall)
with capacity 9 kg/19.84 lbs.)
• If ame goes out while operating, turn gas valve OFF. Wait ve minutes before attempting to relight.
• Due to high surface temperatures always keep a safe distance to avoid burning or clothes catching re.
• Keep fuel supply hose away from any heated surfaces.
Don’t’s
• Never lean over the open Fire Pit or place hands or ngers on the upper portion while in use.
• Do not use Fire Pit for cooking.
• Do not burn any other materials other than what is supplied with and intended for use in Fire Pit.
• Solid fuels shall not be burned in this Fire Pit.
• Do not pour water into Fire Pit.
• Do not move Fire Pit while in operation.
• Fire Pit should never be operated by children. Children must be supervised when they are anywhere near Fire Pit.
• Do not rest feet on Fire Pit.
• Do not use Fire Pit on vehicles or boats. Always operate Fire Pit on at ground outdoors.
when not in use:
• Remove Battery from Ignitor when not using Fire Pit for an extended length of time.
• Clean battery contacts and also those of the device prior to battery installation.
ASSEMBLY INSTRUCTIONS
Make sure the gas supply system
is turned to“OFF”.
Turn knob (N), pull the door out (C) and remove lid (L), which must
remain removed when burner is in operation.
1
2
WARNING
This re pit requires air ow under
the unit. Do not place on uneven
surface or on grass, turf or carpet.
If the repit is put on uneven ground, it
will create diculty in operation of the
sliding door. Adjust the adjustable leg to
keep the re pit level so that the sliding
door can be used correctly.
When the regulator is disconnected from
the cylinder, do not place the reglulator
on the sliding rail; you must hang the
regulator on the hook which can be
found on the back of the door (See
Fig. 2).
Questions? Please call us at
[phone] for assistance.
3Place propane tank (not included) in the metal stand inside Body (B) and make sure the gas tank sits on the metal stand completely.
Turn the wing screw on the outer part of metal stand clockwise to secure the gas tank tightly.

prepare for use:
Keep away from Combustible/Flammable Items
• Do not put any other replace cover or anything ammable on or beneath Fire Pit.
• Combustible materials should never be within 1.83 m/6 ft of the top, 1.22 m/4 ft of back or sides of Fire Pit.
• For use on noncombustible oor material only.
• Keep Fire Pit area clear and free from combustible materials, gasoline, and other ammable vapors and liquids.
Inspect for leaks, wear and damage
• Open Door and check for gas leaks before use - See page 7, Step #8 for instructions on how to check for gas leaks.
• Inspect burner and hose before use - Replace if there is evidence of excessive abrasion, wear, or damage.
• Inspect hose before each use. Hose assembly must be replaced prior to use if there is evidence of excessive abrasion or wear or if
hose is damaged. Use a manufacturer-specied replacement hose only.
Prepare area, ensure proper use of Fire Pit Cover
• Make sure ventilation openings on sides of Fire Pit (BODY) are open and clear of debris.
• Do not lay Nylon Fire Pit Cover over Fire Pit for at least 4 hours after it is turned OFF and has completely cooled down.
• Do not use Fire Pit if any part has been under water. Immediately call a qualied service technician to inspect Fire Pit and to replace
any part of the control system and any gas control that has been under water.
• Remove Nylon Fire Pit Cover from Fire Pit before operating.
when in use:
Do’s
• Use propane cylinders with the following required measurements only: 30.5 cm/12 in (diameter) x 45.7 cm/18 in (tall)
with capacity 9 kg/19.84 lbs.)
• If ame goes out while operating, turn gas valve OFF. Wait ve minutes before attempting to relight.
• Due to high surface temperatures always keep a safe distance to avoid burning or clothes catching re.
• Keep fuel supply hose away from any heated surfaces.
Don’t’s
• Never lean over the open Fire Pit or place hands or ngers on the upper portion while in use.
• Do not use Fire Pit for cooking.
• Do not burn any other materials other than what is supplied with and intended for use in Fire Pit.
• Solid fuels shall not be burned in this Fire Pit.
• Do not pour water into Fire Pit.
• Do not move Fire Pit while in operation.
• Fire Pit should never be operated by children. Children must be supervised when they are anywhere near Fire Pit.
• Do not rest feet on Fire Pit.
• Do not use Fire Pit on vehicles or boats. Always operate Fire Pit on at ground outdoors.
when not in use:
• Remove Battery from Ignitor when not using Fire Pit for an extended length of time.
• Clean battery contacts and also those of the device prior to battery installation.
5
6
4a
ASSEMBLY INSTRUCTIONS
a) Turn Cylinder Valve on the top
of Propane Tank clockwise to close o
gas supply. See Figure 4a
b) Screw Regulator Coupling
clockwise by hand only. Make sure it is
fastened. See Figure 4b
Push Door (C) closed. Rotate door knob (N) clockwise to secure the door shut.
To install Battery (H), unscrew rubber cap of Electric Igniter (K) and place Battery (H) into the Battery Case.
Make sure the positive pole ("+") faces out towards Cap. Screw Cap back to Battery Case tightly.
6
Cylinder Valve
H
Hardware Used
AAA Battery x 1
K
H
6
K
H
4b
Regulator
Coupling
4

8
ASSEMBLY INSTRUCTIONS
a) Place Fire Glass (F) evenly in Fire Bowl (A). Use caution when handling Fire Glass as it is sharp. See Figure 7a
b) Do not place any Fire Glass over the Screen. See gure 7b
c) Completely cover the entire Burner Ring with Fire Glass. See gure 7c
Failure to completely cover the Burner Ring with the Fire Glass will cause ame to extinguish occasionally.
Before using Fire Pit, check for gas leaks.
Perform leak test in a well-ventilated area outside and where no source of spark can occur.
a) After opening door for access, open Tank Valve fully (counter-clockwise).
b) Turn Control Knob to the OFF position.
c) Apply soapy water solution (3 drops dish detergent plus 4 oz. water) to check all connections for leaks before attempting to light Fire Pit.
d) Coat soapy water onto all connections (shown in gure at right, 1, 2 ,3, 4, 5). See Figure 8
e) Turn Control Knob to the ON position. If there are any leaks, soapy water
will bubble where leak is occurring.
If a leak is found, turn Tank Valve o and do not use Fire Pit until repairs are made.
7
WARNING
Keep Fire Glass and other objects
o of Screen (shown at left).
Holes in the Screen must be
exposed in order to allow gas to
escape.
Blocked screen can cause gas to build
inside Fire Pit and ultimately cause an
explosion and risk of serious injury.
Screen
Burner
Ring
CORRECT
Burner Ring is completely
covered (except for Screen).
INCORRECT
Note that the Burner Ring
is visible.
7c
7b
7c
8
123
4
5
Screen
7b
7c
8
7

Fig 9a: Using bolt driver (F) and screws (E), attach long glass
to short glass using parts A, B, C and D as shown. Do not
overtighten
Fig 9b: Repeat step 9a to assemble the remaining glass
sides to complete the entire enclosure. Tighten all screws (E)
with bolt driver (F).
Fig 9c: Place completed glass enclosure into re table.
ASSEMBLY INSTRUCTIONS
WARNING
WARNING
Make sure glass enclosure is xed in the correct
position and all screws are tightened; otherwise
the glass enclosure may slide or fall.
The gas supply system must be turned to“OFF”
position before inserting the glass enclosure into
the re table.
Place the Nylon cover on re pit when not using
re pit for an extended length of time. Put the
glass enclosure over the covered re pit or in a safe
place as in the illustration above. If the glass is
covered with the Nylon cover, the glass enclosure
could fall and break.
ITEM PICTURE DESCRIPTION QTY
A Long Glass 2
B Short Glass 2
C Upper Buckles 4
ITEM PICTURE DESCRIPTION QTY
D Lower Buckles 4
E Screw 24
F Bolt Driver 1
9Glass Enclosure Assembly and Installation
DANGER
HOT GLASS WILL CAUSE
BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
9b
9c
9a

OPERATING INSTRUCTIONS
Before each use, open the door to inspect hose. Replace hose if there are any signs of cutting, wear or abrasion.
WARNING! During initial ring of the Fire Pit, stay away from re pit for 20 minutes as Fire Glass may pop
and cause injury to the face or eyes.
Caution: Only use pressure regulator and hose assembly supplied with Fire Pit. Replacement
pressure regulator and hose assemblies must be specied or supplied by manufacturer.
To Light
1. Turn Cylinder Valve on top of Propane Tank counterclockwise to open gas supply.
2. Close Door on body of Fire Pit.
3. To ignite Burner Ring: See gure 10
a) press and hold Electric Igniter button (a), and
b) at the same time, push in and turn Control Knob (b) counterclockwise, to LOW position.
c) Keep the Control Knob (b) pushed in to light the Burner Ring.
WARNING! If ignition does NOT immediately occur
• release Electric Igniter Button (a) and turn Control Knob to OFF (clockwise).
• WAIT 5 MINUTES to clear out the gas!
• repeat lighting instrutions in Step 3, above
4. After ignition, release Electric Igniter Button (a).
Continue to push and hold the Control Knob for 45 seconds.
Note: Flame should be yellow/blue color.
CARE AND MAINTENANCE
• Store the Fire Pit in a cool dry place away from direct sunlight.
• The Propane Tank must be disconnected and removed from the Fire Pit before the Fire Pit can be stored indoors.
• Make sure both the gas and the Fire Pit are turned o before changing Battery. Please refer to the process of installing the Battery (Step 6).
• Use manufacturer-approved or -supplied replacement parts and accessories only. Use of unauthorized replacement parts may void the warranty.
• Please contact Global Outdoors, Inc. at 1-844-613-9170 for replacement Hoses, Igniters, Fire Glass, Nylon Cover, Regulator and Feet.
• Keep Fire Pit free and clear from combustible materials.
• Visually inspect Burner Ring for blockages (spider webs, dirt, etc.). Keep Fire Pit free and clear from debris.
• After Burner Ring and Fire Glass are completely cooled down, use a soft brush to get rid of mild stains, loose dirt and soil.
Wipe with a soft cloth.
To Extinguish See gure 11
1. Push and turn Control Knob clockwise to "OFF" position.
2. Turn cylinder valve on gas tank to close gas supply if not in use for a long time.
WARNING! Do not place Lid or Nylon Fire Pit Cover on top of Fire Pit for at least 4 hours
after use and until Fire Pit has cooled.
10
11
a
b
a
b

No Igniter battery or igniter battery low on
power Replace with new igniter battery.
Igniter battery is incorrectly inserted Reinsert the battery properly.
Igniter broken or cracked Call customer service for replacement part.
Ignition wire is loose or disconnected to
igniter Reinsert ignition wire.
Electricity leakage in ignition wire or the
needle of ignition wire not aimed at the
burner hole while lighting
Call customer service for replacement part.
Gas cylinder valve not
open Gas cylinder valve not open Open gas cylinder valve.
Inproperly connect between
regulator and gas cylinder
No gas in cylinder No gas in cylinder
Regulator is loose or disconnected to gas
cylinder Check and reconnect the regulator to gas cylinder.
Check whether gas cylinder is empty; if so, replace it.
Gas cylinder valve is opened; when there is
gas remaining in the hose, excess ow
safety valve activated
Turn the control knob to "OFF.” Close the valve
of gas cylinder and disconnect the regulator from the
gas cylinder valve. Turn the control knob to
"LOW.” Wait 30 seconds. Turn the control to
"OFF.” Reconnect the regulator to the gas
cylinder valve. Light the appliance as indicated
in the “To Light"section of manual.
Obvious gas leakage in gas system activates
excess ow safety valve
Check the gas system to see if gas leakage. If yes,
call customer service for help.
Bends or kinks in regulator hose Bend or kinks in regulator hose cause
poor ow of gas through hose Straighten hose of all bends or kinks.
Little or no gas See"Little or no gas" above See"Little or no gas" above.
High or gusting winds Flame extinguished by high or gusting
winds
Move the appliance to the place without high or
gusting winds.
Loose connection of
thermocouple
Loose connection between thermocouple
and valve Call customer service for help.
Debris falls into inside guard and blocks
Inside guard blocked by debris
the entrance of oxygen
Debris falls into inside guard and blocks the
ame in burner hole, which also cause the
low temperature while igniting
Guard covered by debris Guard covered by debris causes
improper burning inside hole of guard
Remove the debris from the guard as indicated in
manual.
Too much carbon deposited
inside guard
The carbon deposits will occur if the
gas burns ineciently when using
the appliance
Open the top of guard by using pincer and clean the
carbon deposits in guard, hermocouple, ignition
wire, and burner. Replace the top of guard .
Excess ow safety valve has
been activated
Little or no
gas
No spark
between
ignition wire
and burner
hole while
pushing the
igniter button.
dr.augehtnaelcdnanepO
Flame goes
out
No power in igniter
The ignition wire isn't conducting
electricity

this page is
intentionally left blank
11

Please call customer service if you have any questions or need additional Fire Glass or other components.
Toll free number: 1-844-613-9170 (English)
Monday to Friday from 9:00 AM to 5:00 PM (Eastern time)
WARRANTY
The manufacturer's warranty will be voided by, and manufacturer disclaims any responsibility for,
the following actions:
• Modication of the re bowl and/or components including the gas valve assembly.
• Use of any component part not manufactured or approved by manufacturer.
• Use and installation other than as instructed in this manual.
Distributed by:
Costco Wholesale Corporation
P.O. Box 34535
Seattle, WA 98124-1535
USA
1-800-774-2678
www.costco.com
Costco Wholesale Canada Ltd.*
415 W. Hunt Club Road
Ottawa, Ontario
K2E 1C5, Canada
1-800-463-3783
www.costco.ca
*faisant aaire au Québec sous
le nom Les Entrepôts Costco
Costco Wholesale UK Ltd /
Costco Online UK Ltd
Hartspring Lane
Watford, Herts
WD25 8JS
United Kingdom
01923 213113
www.costco.co.uk
Costco Wholesale Australia Pty Ltd
17-21 Parramatta Road
Lidcombe NSW 2141
Australia
www.costco.com.au
Importadora Primex S.A. de C.V.
Blvd. Magnocentro No. 4
Huixquilucan, Estado de México
C.P. 52765
www.costco.com.mx
RFC: IPR-930907-S70
San Fernando La Herradura
TM/MC/MR
12