GMT CNT EPS 60 User manual
EPS 60 / 60W Dual Output Rail Mount Power Supply
GMT Endüstriyel Elektronik San. ve Tic. Ltd. Şti.
60W Dual Output Rail Mount Power Supply
EPS 60
General Features
•Short Circuit Protection
•Overload Protection
•Over Voltage Protection
•Rail Mounting
•Insulation Class (2)
•LED Indicator for Energy
•Easy Commissioning
•100% Full Load Test
Input
Voltag Range
88 ~ 264VAC 47~63Hz
AC Current
1A/ 230VAC
Efficiency
%84
Inrush Current
60A/230VAC
Leakage Current
<1mA/240VAC
Output
DC Voltage
24VDC
Rated Current
2.5A
Current Range
0 - 2.5A
Rated Power
60W
Ripple and Noise
150mVp-p
Voltage Tolerance
±1.0%
Setup ad Rise Time
500ms,30ms/230VAC 200ms,30ms/115VAC for full load
Standby Time
50ms/230VAC 20ms/115VAC for full load
Protection
Over Load
105%~160%
The constant current limitation automatically returns to normal operation after the fault condition is
resolved.
Over Voltage
115%~135%
After the overvoltage problem disappears, it returns to the normal operating state.
Environmental
Conditions
Operating Temperature and
Humidity
-20℃~+60℃; 20%~90%RH
Storage Temperature and
Humidity
-40℃~+85℃; 10%~95%RH
Temperature Coefficient
±0.03%/℃(0~50℃)
Vibration
10~500Hz, 2G 10 dk./1 loop, 60 during the minute X, Y, Z vibrations from axes
Safety
Withstand Voltage
I/P-O/P: 3KVAC
Isolation Resistance
I/P-O/P: 100M Ohm/ 500VDC
Standard
Safety Standard
TUV EN60950-1, EN50178
EMC Standard
EN55011,EN55022,EN61000-3-2,-3,EN61000-4-2,3,4,5,6,8,11,ENV50204,EN55024,EN61000-6-2，EN61204-3
Other
informations
Dimensions
100*90*40mm (L*W*H)
Weight
0.33Kg
Before using the device, be sure to read the user manual!
Responsibility for damages, losses and personal accidents caused
by not following the warnings in the user manual belongs to the user.
In this case, the device is out of warranty in case of malfunctions.
Security Precautions
•The device must be de-energized before the cable connections are made.
•Wiring should be done in accordance with the connection diagrams. Otherwise,
the SMPS Power Ski will be damaged or unable to perform its function.
•Do not interfere when there is energy in the power supply.
•The device is CE-branded in EN standards
EPS 60 / 60W Dual Output Rail Mount Power Supply
GMT Endüstriyel Elektronik San. ve Tic. Ltd. Şti.
Dimensions and Mechanical Details (mm)
Installation
DIN Rail mounting process
•Tilt the power supply up and place it on the DIN rail.
•Press down on the rail until is fully seated on the rail.
•To lock it on the rail, press it towards the rail from the front.
•Make sure that the power supply is fully seated on the DIN rail.
*Choose DIN Rail suitable fort he specified width.
DIN Rail removal/disassembly
•Slide the DIN rail release latch by pressing down with a screwdriver as shown in the case.
•You can remove the power supply from the DIN rail by releasing the latch.
*Choose DIN Rail suitable for the specified width.
Maintenance and Support
Device maintenance and repair should be done by trained technical personnel. There may be situations that result in personal injury and/or damage to the device if
unauthorized intervention is made. Contact our company for the repair of defective devices.
For questions about the device, you can contact us using the contact information below.
GMT ENDÜSTRİYEL ELEKTRONİK SAN. VE TİC. LTD. ŞTİ.
Çubuklu Mahallesi Boğaziçi Caddesi No:6/B 34805 Beykoz / İstanbul / Türkiye
T +90 (216) 668 00 06
M +90 (534) 363 75 33 / +90 (534) 882 12 22
F +90 (216) 668 00 03
http://www.gmtcontrol.com/
