Goalsetter Systems Top Hoops Extreme Series User manual

www.TopHoops.com
Top Hoops • [e-mail] • 888.878.2942

Safety Instructions
Owner must ensure that all installers and players know and comply
with these rules for safe assembly, installation, operation and use
of the system. Proper and complete assembly, use and supervision
is essential for proper operation of the product and to reduce
the risk of accident or injury. DO NOT ATTEMPT TO ASSEMBLE
AND INSTALL THIS PRODUCT WITHOUT FOLLOWING THE
INSTRUCTIONS CAREFULLY.
WARNING
1. Failure to follow these instructions may result in death, seri-
ous injury and/or property damage and will void the warranty.
Do not install or use this product unless the instructions
within this manual have been carefully read and understood.
2. Locate your goal away from potential dangers, including
walls, trip hazards, high-traffic areas or where a vehicle might
come into contact with goal post, backboard or rim.
To avoid severe injury or death, do not locate goal under
power lines that may come into contact with the goal as it
is raised.
3. Two or three people in good physical condition and capable of
lifting at least 90-100 lbs. (40-45 kg) each are recommended
for safe installation and assembly.
• If using a ladder during assembly, use extreme caution. Follow all
warnings and cautions on the ladder carefully.
• Installation and assembly of this product will require lifting and
bending that may result in injury to anyone not accustomed to
this type of activity.
•
Before digging for the ground anchor, check for underground
power, gas, telephone, water and other utility lines. Failure to do
so could result in serious injury. See 811 One Call Warning box on
this page for more information or call your local utility company.
• If an auger or post hole digger is used, be sure you read and fol-
low all instructions, warnings and cautions for such equipment.
• Ensure there are no overhead power lines within a 20 ft. (7 m)
radius of the goal location.
• Climate, corrosion or misuse could result in system failure.
• Keep organic material away from the pole base. Dirt, grass, litter
etc. could cause corrosion or deterioration.
• Only use parts provided with your Goalsetter®basketball goal
system or replacement parts provided by Goalsetter Systems,
Inc. Use of other parts (a) may cause the goal system to fail,
(b) could result in death, serious injury or property damage,
and (c) will void the warranty.
• With rim set at 7’-0” playing height, the minimum operational
height is 6’-4” (1.93 m) to the bottom of the backboard.
• DO NOT CLIMB THE POLE OR HANG on the rim or any part of
the goal system. This includes the backboard, support braces
and net. The product is not designed for such use and property
damage or personal injuries such as cuts, broken bones, nerve,
spinal cord or brain injury or death could occur.
• Use caution when performing dunking activities with this product.
• During play keep players’ faces away from the backboard, rim
and net or serious injury could result.
• Players must wear a mouth guard to avoid dental injuries.
2
• Do not wear jewelry (rings, watches, necklaces, etc.) or other
loose objects that could become tangled in the net or injure
another player.
•
Before each use, check the goal system for loose hardware, exces-
sive wear and signs of corrosion. Repair the system before use.
• NEVER play on damaged equipment.
•
When adjusting the system height, keep hands and fingers away from
moving parts. DO NOT allow children to adjust the system height.
• Check the goal system frequently for signs of corrosion. Remove
surface rust and loose paint completely, and repaint with exterior
enamel paint. If rust or corrosion has penetrated or pitted any
components of the goal, DO NOT allow play and repair or replace
parts immediately.
• DO NOT use the goal system to lift or hoist anything.
• Use caution when using this goal system. Most injuries are
caused by misuse and/or not following these instructions.
IMPORTANT
Enclosed underneath the protective sheeting on your backboard
is a warranty registration card. YOU MUST FILL OUT AND
MAIL IN THIS CARD IN ORDER TO HAVE A VALID WARRANTY.
You may also fill out a warranty registration online at
www.goalsettersystems.com.
Retain this manual for future reference of operation, maintenance
and parts information.
The information in this manual is based on the latest information
available at the time of publication. Your goal may have product
improvements and options not yet contained in this manual.
Goalsetter Systems, Inc. reserves the right to make changes at any
time without notice or obligation.
Contact the manufacturer if technical assistance is required.
Additional copies of these instructions are available from:
Goalsetter Systems, Inc.
1-800-362-GOAL (4625)
www.goalsettersystems.com
WARNING
Before digging for the ground anchor,
contact your local One-Call system
(dial 811) in your area.
Utility Markings
Color Definition
Red Electric
Yellow Gas, Oil, Petroleum
Orange Communication, Phone, TV
Blue Potable Water, Irrigation
Green/Brown Sewer
White Proposed Dig
1-888-258-0808

3
Goal Specifications
Determine Installation Location
Consider the following to determine where to install your
Goalsetter® Basketball Goal:
• When extended, will backboard overhang obstruct driveway or
other important space? Maximum overhang: 61” (1.55 m) from
the front of the pole to the front of the rim.
• Is there room so vehicles backing out of driveway do not strike
backboard or rim?
• Will court markings be used?
• How much playing surface is needed?
• How much playing surface will be under the backboard?
(Having the edge of the playing surface directly underneath
the backboard can result in trip hazards and unpredictable ball
action following a shot. Try to have as much playing surface as
possible behind the backboard.)
• Other functions of playing surface (driveway, playground, etc.)
• Will the goal be at least 20 ft. (7 m) from any overhead power
lines? (No overhead power lines should be within a 20 ft.
(7 m) radius of the goal.)
• Will the ground anchor for the goal avoid underground power,
gas, telephone, water and other utility lines? (See 811 One Call
Warning box on page 2 for more information or call your local
utility company.)
Required Tools and Materials:
• Spade • Wheelbarrow
• Shovel • Cement Trowel
• Tape Measure • Stir Rod
• Level • Auger/Post Hole Digger (optional)
• Hoe •
10-14, 60 lb Bags of Dry Concrete Mix
• Water (or 1/4-1/3 yard of ready mix concrete)
• Rubber Mallet • 1/2” Drive Torque Wrench
• Steel Punch • Phillips Screwdriver
• Stepladder • 9/16” & 3/4” Wrenches and Sockets
X454 X448
Pole Size: 4”x4” 4”x4”
Backboard Size: 36”x54” 32”x48”
Weight w/Acrylic: 260 lbs. 255 lbs.
Weight w/Glass: 300 lbs. 285 lbs.
(A) Height Range: 6’8”-10’ 6’8”-10’
(B) Extension Distance:
at 10’ 31” 31”
at 8’ 36” 36”
at 7’ 31” 31”
(C) Maximum Overhang: 61” 61”
(D) Distance Rim to Backboard: 25” 25”
(E) Distance Rim to Top of Goal: 27
3/4
”23
3/4
”
(F) Crank Distance: 18” 18”
(G) Crank Height: 42” 42”
(H) Crank Turn Radius 10” 10”
(I) Pole Height: 9’9” 9’9”
A
B
DC
I
H
G
F
E
Playing Surface
6'-0"
19'-9"
50'-0" Optimum Inside Sidelines
15'-0"
19'-0"
25'-0"
63"
15"
12'-0"
4'-0"
Note: Lines are 2" wide.
Court Markings
(Reference Only):
Regulation Court Lengths
High School: 84’
College & Professional: 94’

4
TIME OUT TIP: The arrow on the decal
MUST be pointing toward the playing surface.
Step 6: Position anchor in center of hole with hinge side
toward and parallel with playing surface. Using a level, ensure
the anchor is level front-to-back and left-to-right. All edges of the
ground anchor must be 6” (15.2 cm) away from all sides of hole
and the top of the ground anchor within a range of 1”- 3” (25-75
mm) above the level of the playing surface.
TIME OUT TIP: As you add concrete, occasionally
insert a stir rod (such as a broomstick) into three
or four places in the concrete and plunge up and
down to help eliminate air bubbles.
Step 7: Continue adding concrete until concrete is within
1”- 1.5” (25-38 mm) of anchor plate bottom, or level with the
landscape – whichever comes first. Slope top of concrete away
from pole with trowel to create a smooth surface.
IMPORTANT
• Periodically re-check the level of the anchor plate in both
directions as you add more concrete.
• Slope the top of the concrete ll away from the ground
anchor in all directions to shed moisture away.
TIME OUT TIP: If you must adjust the height,
be sure to re-check level and that the anchor is
parallel with playing surface!
Step 8: If needed, adjust anchor plate height. The top of
the ground anchor should be within a range of 1”- 3” (25-75 mm)
above playing surface. Be sure to re-check level.
Step 1: Locate and unpack ground anchor. Remove
plastic plugs from bolt holes and ensure the threads are in good
condition. REPLACE THE PLUGS – they will keep concrete and
debris from the bolt holes during installation. Leave the hinge pin
in place as well.
Step 2: Determine hole location. When installed, the
edge of the ground anchor must be a minimum of 6” (15.2 cm)
away from the playing surface. Follow One Call or your utility’s
recommendations as to how close you may dig to a marked utility.
IMPORTANT
You MUST dig the anchor hole at least 48” (1.2 m) deep.
WARNING
Before digging for the ground anchor, check for underground
power, gas, telephone, water and other utility lines. Failure to do
so could result in serious injury. See 811 One Call Warning box
on page 2 for more information or call your local utility company.
Step 3: Dig hole 48” to 50” (1.2 m – 1.3 m) deep and 18” (0.5
m) in diameter using a spade, shovel, auger or post hole digger.
TIME OUT TIP:
If you plan on mixing concrete in
stages, work quickly to minimize time between batches.
Step 4: Mix concrete. Put concrete in wheelbarrow. Add the
amount of water recommended on the bag, and mix with hoe.
Step 5: Begin adding concrete into hole until concrete is
approximately 28”- 30” (.7 m – .8 m) deep.
1”- 3” (25-75 mm) minimum
14-18”
(0.36-0.5 m)
6" (152 mm)
all sides
Playing
Surface
42”
(1.1 m)
6” (152 mm)
48-50”
(1.2-1.3 m)
6" (152 mm)
minimum AND
parallel
Playing Surface
Check level both
directions
Ground Anchor Installation

5
HARDWARE:
Pole Assembly
IMPORTANT
• Allow 48 hours for concrete to cure before beginning.
• Check to see that no concrete or debris obstructs threads in
ground anchor bolt holes by threading anchor bolts in and out.
Step 1: Remove ve plastic plugs from threaded
holes in ground anchor. Also remove hinge pin and hex nut
and place near anchor plate. (These will be used in Step 3.)
TIME OUT TIP: To protect pole nish, place square
packing pad (included in pole box) on the ground
at the bottom of pole. Remove once pole is held by
installation clip.
Step 2: Unpack pole and jack. Jack comes packaged with
the pole. Jack will be used in Jack Attachment instructions.
Step 3: Align pole hinge with anchor plate hinge, then
insert hinge pin and hand tighten hex nut.
Step 4: Lift pole to approximately 30º and attach
installation clip to ground anchor and pole to maintain the
installation angle.
IMPORTANT
The installation clip MUST remian in place until pole is raised in
Goal Alignment, page 9.
WARNING
Two or three people in good physical condition and capable of
lifting at least 90-100 lbs. (40-45 kg) each are recommended for
safe installation and assembly.
3/8”x 5” Hinge Pin (1) 3/8” Hex Nut (1)
1/2”x 11/4”
Anchor Bolt (1-black)
Step 4
Step 3
Installation
Clip
Hinge
Pin
Hex
Nut

Step 2
Step 3
Lower
Extension
Arm
Upper
Extension
Arm
Nylon
Washer
Flat
Washer
Flat
Washer
Flat
Washer
Flat
Washer
Nylon
Washer
Locknut
Locknut
Extension
Arm Bolt
1/2” Nylon Washer (8)
6
Step 3: Attach upper extension arm pivot holes
with upper holes in pole following the same hardware and
procedure as in Step 2.
Step 4:
Remove protective material from extension arms.
Extension Arm Attachments
WARNING
Two or three people in good physical condition and capable of
lifting at least 90-100 lbs. (40-45 kg) each are recommended
for safe installation and assembly.
TIME OUT TIP: The lower extension arm is the
longer of the two arms.
Step 1: Unpack extension arms. Align lower extension
arm pivot holes with lower bushings on pole.
Step 2: Attach lower extension arm pivot holes with
lower bushing on pole using the following: one 1/2” x 8” bolt,
two flat washers, four nylon washers and a locknut. Tighten with
3/4” wrench and socket so the bushings on the extension arm
meet the bushing on the pole. Do not over-tighten.
1/2”Locknut (2)
1/2”x 8” Extension Arm Bolt (2)
1/2” Flat Washer (4)
HARDWARE:
TOOLS:
3/4” Socket, 3/4” Wrench, Rubber Mallet

7
Step 3: Extend jack by turning jack handle counter-
clockwise until upper jack bracket is aligned with holes in lower
extension arm.
IMPORTANT
Attach upper end of jack to lower extension arm by extending
the jack; DO NOT swing arm to make the attachment.
Step 4: Attach upper end of jack to lower extension
arm using the following: one upper jack pole bolt, two at
washers, two nylon washers, two spacers and a locknut. Tighten
with a 3/4” wrench and socket. NOTE: DO NOT over-tighten. Snug
tighten only.
Jack Attachment
WARNING
Two or three people in good physical condition and capable of
lifting at least 90-100 lbs. (40-45 kg) each are recommended
for safe installation and assembly.
IMPORTANT
The jack is packaged with the pole.
Step 1: Unpack the jack.
Step 2: Attach lower end of jack to bracket on pole
using one lower jack pole bolt, two flat washers, four nylon
washers and a locknut. Tighten with a 3/4” wrench and socket.
NOTE: DO NOT over-tighten. Snug tighten only.
HARDWARE:
TOOLS:
3/4” Socket, 3/4” Wrench, Rubber Mallet
1/2” Nylon
Washer (6)
1/2” Flat
Washer (4) 1/2” Locknut (2) 1/2” Spacer (2)
Step 2
Lower
Extension
Arm
Upper
Extension
Arm
Step 4
Locknut
Flat
Washer
Upper Jack
Pole Bolt
Lower Jack
Pole Bolt
Nylon
Washer
Spacer
Step 3
Flat
Washer
Nylon Washer
Flat
Washer Flat
Washer
Locknut
1/2”
x 8” Upper Jack Pole Bolt (1) 1/2” x 4” Lower Jack Pole Bolt (1)

8
Step 3
Backboard
Bolt
Locknut
Flat
Washer
Flat
Washer
Flat
Washer
Step 2
WARNING
Two or three people in good physical condition and capable of
lifting at least 90-100 lbs. (40-45 kg) each are recommended for
safe installation and assembly.
IMPORTANT
The installation clip MUST be in place to maintian the proper
installation angle.
TIME OUT TIP: Lay the unopened box with
Goalsetter logo upside down AND let the lid
open up and fold away from the goal system.
Step 1: Open lid of box containing backboard and slide
the backboard face down under lower extension arm, with rim
mounting plate facing towards goal system.
TIME OUT TIP: The backboard attachment can be
eased by cranking the jack to help align lower
extension arms above the backboard prior to lifting it.
Backboard Attachment
Step 2: Carefully lift the bottom of the backboard to
align lower backboard holes with lower extension arm
holes. Using ratchet and wrench, attach backboard to arm using
the following hardware: two backboard bolts, four at washers
and two locknuts. NOTE: This is a pivot point! DO NOT over-
tighten. Snug tighten only.
Step 3: Lift top of backboard to align upper holes
with upper extension arm holes using the same hardware
and procedure as in Step 2.
1/2” Locknut (2)
1/2” x 8”
Backboard Bolt (2) 5/8” Flat Washer (4)
HARDWARE:
TOOLS:
3/4” Socket, 3/4” Wrench

WARNING!
For safe assembly, do the following:
• Use two or three people to raise goal assembly and hold it in
a vertical position. Two or three people in good physical con-
dition and capable of lifting at least 90-100 lbs. (40-45 kg)
each are recommended for safe installation and assembly.
• DO NOT adjust height of backboard or attach rim until pole is
raised and appropriately bolted.
• Correct sequence of hardware installation MUST be followed
during assembly.
To avoid injury, keep fingers and toes away from the ground
plate while raising the goal assembly to the vertical position.
Step 1: Remove banding and edge protection from
backboard. Peel back TOP 1/3of protective sheeting from the
backboard. This will allow you to reach the sheeting once goal
has been raised, yet protects the surface of the backboard during
installation.
Step 2: Locate ve anchor bolts. Prepare them for use by
having lock washers slipped on and placed near ground anchor.
Step 3: Using at least two people, carefully push
up on backboard to raise goal assembly to vertical
position. The installation clip will fall away. Save installation clip
for future disassembly.
9
Step 4: Fasten pole to threaded ground anchor plate
by installing and hand tightening the three rear anchor bolts with
lock washers.
Step 5: Fasten pole to threaded ground anchor plate
by installing and hand tightening the two front anchor bolts with
lock washers.
TIME OUT TIP: Install rear three anchor bolts rst
and then the front two anchor bolts.
Step 6: Snug tighten the ve anchor bolts, then
check goal assembly with a level and inspect visually
to determine if it is parallel and plumb to the playing surface.
Step 7: If adjustments are necessary, slightly loosen
bolts to rotate goal.
Step 8: Fully tighten ve bolts using a 3/4” socket with a
torque wrench. The torque wrench is to be set at 75 ft/lb on dry
threads and 55 ft/lb on lubricated threads. NOTE: The anchor
plate is threaded, so there is no need to use nuts on bolts.
IMPORTANT
The bolts must pass all the way through the ground anchor
plate. If they do not pass through the ground anchor plate
when fully tightened, STOP installation, contact Goalsetter
Systems, Inc. and DO NOT allow play.
Goal Alignment
Step 3
1/2”x 11/4”
Anchor Bolt (5-black)
1/2” Lock
Washer (5)
HARDWARE:
TOOLS:
3/4” Socket, Level, 1/2” Drive Torque Wrench
Playing Surface
Step 4
Step 5
Lock
Washer
Anchor
Bolt
Ground
Anchor Plate
End of anchor bolt
should extend 1/8”
below anchor plate.

10
Step 3
Step 4
Flat
Washer
Flat
Washer
Backboard
Bolt
Backboard
Bolt
Nut
Nut
Flat
Washer
Flat
Washer
Lock
Washer
Lock
Washer
Rim Attachment
NOTE: Use all steps of the following instructions to install a reex
rim. To install a static rim, follow all steps except Steps 2 and 6.
TIME OUT TIP: Your warranty card is located
behind protective sheeting. You MUST fill out and return
this card to activate your warranty.
Step 1: Unpack rim. Remove any remaining cardboard edge
protectors and protective sheeting from backboard.
IMPORTANT
• Four bushings are factory installed on the backboard. If
loose, make sure to have them seated properly when tighten-
ing rim bolts. If missing, contact Goalsetter or dealer.
DO NOT install rim without bushings. If the bushings are
not in place, glass backboards can shatter and acrylic
backboards can crack!
• Correct sequence of hardware installation MUST be followed
during assembly.
• Be sure to attach rim bolt backplate when performing Step 3.
Failure to install can result in backboard failure/breakage.
Step 2: If not already removed, remove cover plate
screws and cover plate from rim assembly.
Step 3: Starting with the top two mounting holes,
loosely attach rim to backboard, being sure to
place the rim bolt backplate on the rear side of the
backboard and follow the hardware sequence as shown
in the illustration below. Snug tighten hardware - a
9/16” open-end
wrench may be necessary.
Step 4: Repeat hardware sequence outlined in Step 3
for lower rim mounting holes.
Step 5: Level rim side to side and then fully tighten
hardware.
Step 6: Position cover plate and attach with cover
plate screws.
Step 7: Attach net to rim.
3/8” x 2”
Backboard Bolt (4)
3/8”
Flat Washer (8)
3/8”
Lock Washer (4)
3/8”
Nut (4) Cover Plate
Screw (4)
HARDWARE:
TOOLS:
Level, 9/16” Wrench, 9/16” Socket, Phillips Screwdriver
Rim Bolt Backplate (1)
Rim Bolt
Backplate
Step 6
Cover Plate
Screw
Cover Plate
Screw
Cover
Plate
TIME OUT TIP: Level rim side to
side before tightening backboard bolts.
Factory Installed Bushing
(Backboard damage can result if not installed)

Step 1: Position top of rim 7’ above playing surface by turning
crank handle.
Step 2: Measure distance with a tape measure for accuracy.
Step 3: Draw a mark on inner tube at edge of outer jack tube.
Step 4: Extend jack approximately ½”. Peel ½”
of backing off the top of the decal (by the 7’
mark). Slip decal under the outer tube on the
jack until the 7’ line is even with the
drawn mark.
Step 5: Hold decal square with the jack and
peel backing off, pressing decal down onto jack
as backing is peeled off.
11
Height Indicator Attachment
8
7
71/2
Step 1
Step 2
Step 4
TOOLS:
12’ Tape Measure
DECAL:
7’

12
Goal Assembly, cont.
Operation
Crank handle turns clockwise for goal
to go up, crank handle turns counter
clockwise for goal to go down.
Height indicator indicates goal height
from 7’ to 10’.
To prevent undesired height
adjustment, remove crank pin and
crank handle.
Maintenance
The life of your basketball goal system depends on many
variables. The climate, exposure to corrosives such as salt,
organic materials, pesticides, or herbicides, and excessive use or
misuse can all contribute to failure of the goal system, which may
cause property damage or personal injury. Before each use, check
the goal system for loose hardware, excessive wear, abuse, or
vandalism or signs of rust or corrosion.
For safety reasons, and to prolong the life of your basketball
system, you must take the following preventative measures:
• Check all nuts and bolts. Inspect the threads and replace if
necessary. If any are loose, tighten them.
• Check all parts for excessive wear and tear. If necessary, replace
any parts that have been worn or damaged through usage.
• Check all sections of the goal system for visible rust or chipped
or cracked paint, and if present, repair appropriately. See Paint
Touch-Up on this page.
IF RUST OR CORROSION HAS PENETRATED ANY COMPONENT,
DO NOT ALLOW PLAY ON THE GOAL AND REPLACE PARTS
IMMEDIATELY.
• Contact Goalsetter Systems, Inc. for replacement parts. Only
use parts provided by Goalsetter Systems, Inc. Use of other
parts (a) may cause the goal system to fail, (b) could result in
death, serious injury or property damage, and (c) will void the
warranty.
• Inspect the Warning Sticker on the pole. If it is ripped, faded, or
illegible, contact Goalsetter Systems, Inc. to request a replace-
ment Warning Sticker.
Cleaning
The exterior nish of your Goalsetter®goal is designed for
outdoor environments and should only require periodic cleaning
and inspection for imperfections that could develop over time.
When cleaning is necessary, Goalsetter recommends using water
and a mild dish detergent applied with a soft, non-abrasive cloth.
IMPORTANT
DO NOT use abrasive cleaners to clean the goal. Damage to the
finish may result.
Paint Touch-Up
Goalsetter Systems, Inc. uses a two-part acrylic-
enamel paint on the goals. With periodic inspection
and service when needed, the high-gloss finish is
designed to last for many years. A small bottle of
black paint with brush is provided in the hardware
kit for touch up of imperfections as they develop. If
more touch up is required, please contact Goalsetter
Systems, Inc. or your local Goalsetter Dealer.
Lubrication
The jack is pre-lubricated. As with any mechanical component,
periodic inspection and service is required. Goalsetter Systems,
Inc. recommends applying lubrication each spring and fall to keep
a smooth operation of the height actuator. Failure to do so could
result in jack failure and not be covered under warranty.
Use several shots of grease in the grease zerk.
Black Touch-Up Paint
Ready to Play
8
7
71/2
Grease Zerk

13
Warranties
IMPORTANT
Enclosed underneath the protective sheeting on your backboard
is a warranty registration card. YOU MUST FILL OUT AND
MAIL IN THIS CARD IN ORDER TO HAVE A VALID WARRANTY.
You may also fill out a warranty registration online at
www.goalsettersystems.com.
LIMITED WARRANTY
LIMITED LIFETIME WARRANTY: Subject to proper installation and
normal, intended use, and subject to the limitations set forth below,
Goalsetter Systems, Inc. warrants to the original retail purchaser
that all structural components of Goalsetter®Systems Signature
Series*, Extreme Series** and GS Wall-Mount Series*** basketball
systems are free of defects in material and workmanship for the
duration of ownership by such original retail purchaser or 5 years after
discontinuation of the product by Goalsetter Systems, Inc..
*Signature Series – MVP, Captain, All-American, All-Star, Contender,
Champion;
**Extreme Series – X672, X660, X560, X554, X454, X448;
***GS Wall-Mount Series – GS72 Wall-Mount, GS60 Wall-Mount, GS54
Wall-Mount, GS48 Wall-Mount; Tournament Series – Elite, Classic; GS
Portable Series – GS1000, GS2000, GS2500, GS3000, GS3500.
LIMITED WARRANTY: Subject to proper installation and normal,
intended use, and subject to the limitations set forth below, Goalsetter
Systems, Inc. warrants to the original retail purchaser that all structural
components of (a) Goalsetter Systems Tournament Series* basketball
systems are free of defects in material and workmanship for a period
of ve years from date of purchase (b) Goalsetter Systems GS
Portable Series* basketball systems are free of defects in material and
workmanship for a period of two years from date of purchase.
Any warranty on a basketball system excludes the rim. Rim warranties
are as follows: Rims shall be free from defects in materials and
workmanship from the date of purchase as follows: Single Ring Static
Rim: two-year limited warranty; Double Ring Static Rim: limited lifetime
Warranty; Home Court Flex Rim: one-year limited warranty; Heavy Duty
Flex Rim: two-year limited warranty; GS Ultra Flex Rim: ve-year limited
warranty; GS Collegiate Breakaway Rim: ve-year limited warranty;
Double Ring Static Galvanized Rim: limited lifetime warranty.
Padding Warranty: Padding shall be free from defects in materials
and workmanship from the date of purchase as follows: Multi-Purpose
Backboard Edge Padding: one-year limited warranty; Indoor Backboard
Edge Padding: ve-year limited warranty (indoor only); Custom Fitted
Pole Padding: one-year limited warranty; Wrap Around Pole Padding:
one-year limited warranty
MISC PRODUCT WARRANTIES: The following products shall be free
from defects in materials and workmanship from the date of purchase as
follows:
Other Portable Systems: GS1000 – 2 year limited warranty; GS4500:
5-year limited warranty; GS5000: Base, 10-year limited warranty; Pole,
Backboard, Hand Crank, Padding and Rim, 5-year limited warranty;
GS6000 & GS7000: Portable structure, 10-year limited warranty;
Backboard, limited lifetime warranty; Padding and Rim, 5-year limited
warranty
Playground Structures: All GS MAX & GS Double MAX Systems:
10-year limited lifetime warranty; RP775 3-1/2” Gooseneck Pole: 10-
year limited warranty; RP776 3-1/2” Adjustable Pole: 10-year limited
warranty; RP777 4-1/2” Gooseneck Pole: 25-year limited warranty;
RP778 4-1/2” Adjustable Pole: 25-year limited warranty; RP780 Mega
Duty Pole: limited lifetime warranty
Gym Structures & Accessories: Stationary, Side Fold and Swing Up
Wall Mounted Structures: limited lifetime warranty; Height Adjuster: 10-
year limited warranty; A11067 Wall Mount Power Winch: 5-year limited
warranty; A11068 Portable 110 Volt Winch: 1-year limited warranty;
A11008 Fail-Safe Structure Catch: 10-year limited warranty; A11200
Easy-Up Youth Mini Goal: 1-year limited warranty on structure and rim,
limited lifetime warranty on backboard
Rims & Nets: R10126 Single Ring Static: 2-year limited warranty;
R10226 Double Ring Static: limited lifetime warranty; R10326 Heavy
Duty Reex: 2-year limited warranty; R10426 GS Ultra Flex: 5-year
limited warranty; R10554 GS Collegiate Breakaway: 5-year limited
warranty; R10654 GS Pro Breakaway: 5-year limited warranty; R10834
Home Court Reex: 1-year limited warranty; R10935 GS Premier
Breakaway: 5-year limited warranty; A11013 Steel Net: 2-year limited
warranty
Institutional Backboards: CB4272RG 42x72 Competition Glass: limited
lifetime warranty (indoor only); CB4272RGCV 42x72 Competition
Glass Conversion: limited lifetime warranty (indoor only); CB4872RG
48x72 Rectangular Glass: 20-year limited warranty (indoor only);
RB4254GC 42x54 Glass Conversion: limited lifetime warranty (indoor
only); CB3954FG Fan-Shaped Glass: limited lifetime warranty (indoor
only); RB4260RS 42x60 Rectangular Steel: 10-year limited warranty;
RB3954RS 39x54 Rectangular Steel: 10-year limited warranty;
RB3954FS 39x54 Fan Steel: 10-year limited warranty; RB3954RA
39x54 Rectangular White Aluminum: limited lifetime warranty on direct
mount pole systems; RB3654FCA 36x54 Fan Cast Aluminum: limited
lifetime warranty on direct mount pole systems, otherwise 10-year
limited warranty; RB3654FA 36x54 Fan White Aluminum: limited lifetime
warranty on direct mount pole systems, otherwise 10-year limited
warranty; RB4272RF 42x72 Rectangular Fiberglass: 10-year limited
warranty; RB4254RP 42x54 Rectangular Polycarbonate: limited lifetime
warranty; RB4254RG 42x54 Rectangular Glass: limited lifetime warranty;
RB3954FP 39x54 Fan Polyethylene: limited lifetime warranty
The Limited Lifetime Warranty and the Limited Warranty shall cover
damage or failure that occurs during the course of NORMAL or
INTENDED USE of the product. Normal or intended use shall be
described as activity that is necessary for the participation in the
sport for which the equipment is designed. NOT COVERED is damage
caused by deliberate hanging, multiple player hanging, vandalism,
non-basketball activities or any other activity that could be regarded as
abusive.
A limited lifetime warranty is effective for the duration of ownership
by the original retail purchaser or 5 years after discontinuation of the
product by Goalsetter Systems, Inc.
Goalsetter Systems, Inc. shall have the right to require the purchaser to
deliver at its expense the allegedly defective product to Goalsetter for
testing, repair or replacement. Goalsetter shall not be responsible for
any expenses associated with the replacement or removal of the product
from its application for such delivery.

THE WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAMAGED BY
ACCIDENT, USE FOR PURPOSES FOR WHICH IT IS NOT INTENDED,
AS THE RESULT OF IMPROPER INSTALLATION, FAILURE TO FOLLOW
INSTALLATION, CARE OR MAINTENANCE INSTRUCTIONS PROVIDED
WITH THE PRODUCT, USE OF PARTS NOT PROVIDED BY GOALSETTER
SYSTEMS OR ANY MODIFICATION OF ANY PRODUCT BY THE
CUSTOMER UNLESS APPROVED BY GOALSETTER SYSTEMS, INC., OR
OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIALS OR
WORKMANSHIP,
The sole obligation of Goalsetter Systems, Inc., and the exclusive
remedy under the applicable warranty, is repair or replacement of any
component part determined by Goalsetter Systems, Inc. to be defective
and covered by the warranty. Goalsetter Systems, Inc. will not be
liable for any other damages or expenses. The applicable warranty is
expressly in lieu of all other warranties, express or implied. Goalsetter
Systems, Inc. does not assume, and no other person or representative
is authorized to assume for Goalsetter Systems, Inc. any other liability in
connection with the sale of Goalsetter System products.
NOT COVERED BY WARRANTY
• Use in non-residential applications of Glass backboards on Signature
Series systems.
• Use in non-residential applications of Extreme Series and Tournament
Series complete systems.
• Any products subjected to abuse, negligence, improper installation,
vandalism, acts of God, alteration of product
and any other events beyond the control of Goalsetter Systems, Inc.
• Paint or rusted parts. Touch-up paint is included in all hardware kits.
• Deterioration of product due to time or wear and tear.
Normal deterioration of products due to atmospheric conditions,
weather, wear and tear (including scratching or scuffing paint from
normal use), or other causes that do not affect functional use are not
covered by Goalsetter Systems, Inc. warranties. All warranties are valid
only when product is used in the intended application & when installed
according to Goalsetter Systems instructions. Warranty may be void if
maintenance instructions in the Owner’s Manual are not followed. If you
did not receive an Owners Manual, please call 1-800-362-4625 and one
will be mailed to you.
DISCLAIMERS: THE APPLICABLE WARRANTY IS EXPRESSLY IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. AND ALL OTHER
WARRANITES ARE HEREBY DISCLAIMED, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. UNDER NO CIRCUMSTANCES
SHALL GOALSETTER SYSTEMS, INC. BE LIABLE FOR ANY INDIRECT,
CONSEQUENTIAL, SPECIAL, INCIDENTAL, PUNITIVE, OR EXEMPLARY
DAMAGES OF ANY KIND.
THE PRODUCT IS INTENDED TO BE USED TO PLAY THE SPORT OF
BASKETBALL. ALL SPORTS INVOLVE RISK OF INJURY. THE USER
ASSUMES ALL RISK OF INJURY RESULTING FROM THE USE OF THIS
PRODUCT. ALL PRODUCTS ARE SOLD ON THIS CONDITION AND NO
REPRESENTATIVE OF THE COMPANY MAY WAIVE OR CHANGE THIS
POLICY.
Some states do not allow the exclusion or limitation of implied
warranties or consequential or incidental damages, so the above
limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you
may also have other rights which may vary from state to state.
WARRANTY CLAIMS: All returns must be arranged through the
Goalsetter Systems, Inc. dealer where the product was originally
purchased. Warranties do not cover dealer service charges, labor
charges, freight charges, and travel expenses associated with
replacement, repair or removal of warranty items. A Goalsetter
Warranty Claim form must be completed, and photos submitted,
together with proof of purchase, for any item you wish to claim under
warranty. If the purchase was not made through a dealer, this form
is available by email, fax or mail. In response to your claim, you will
receive an order confirmation as well as a notice stating whether
Goalsetter Systems, Inc. needs your warranty item returned. Goalsetter
Systems, Inc. will notify you by fax or phone if we determine that the
item cannot be claimed under warranty. Goalsetter Systems, Inc. is
not responsible for any charges for labor to install or repair defective
product without prior authorization. Goalsetter Systems, Inc. will
determine the most economical method to either repair or replace
product before any work is to commence.
Questions or Comments?
Phone [phone]
Fax: [phone]
Email:[email protected]
www.goalsettersystems.com
GOALSETTER and GOALSETTER BASKETBALL logo are registered
trademarks of Goalsetter Systems, Inc. in the United States. BEST IN
BASKETBALL™ is a trademark of Goalsetter Systems, Inc.
This product is covered by various U.S. and Canadian patents, including
U.S. Patent #5,211,393. Patent infringement will be prosecuted.
No part of this manual may be reproduced in any form or by any means
electronic or mechanical, including photocopying, recording, or by any
information storage and retrieval systems without the express written
consent of Goalsetter Systems, Inc.
Copyright 2006.
All rights reserved.
Revised 1/2011
Goalsetter Systems, Inc.
14

15

Phone [phone]
Fax: [phone]
Email:[email protected]
www.goalsettersystems.com
1/2011