gofanco KVMHD2-Dual User manual

2-Port Dual-Head HDMI 2.0
KVM with USB 2.0
User's Guide
G4-0102A
P/N:KVMHD2-Dual

2
Thank you for purchasing from gofanco. Our products
aim to meet all your connectivity needs wherever you
go. For optimum performance and safety, please read
the instructions carefully and keep this User's Guide for
future reference. If you need more information about
our products, please visit www.gofanco.com. For
technical support, email us at [email protected].
For drivers or manual download, please go to
www.gofanco.com/downloads.
Important Safety Notices
Pleasereadsafetyinstructionscarefullybeforeinstallation
and operation.
• Please pay close attention to all warnings and hints
for this device
• Do not expose this unit to rain, heavy moisture, or
liquid
• Do not put any items into the device or attempt to
modify its operation
• Do not repair the device or open the enclosure
without professional guidance to avoid electric
shocks. Doing so may void your warranty
• Keep the product in a well-ventilated location to
avoid damage from overheating
• Shut off power and make sure environment is safe
before installation
• Do not plug the HDMI or DisplayPort cables
in/out when the device is in use to avoid cable
damage. Make sure they are plugged into the
correct ports
• Use the included power adapter only. Make sure
the specification matches if using 3rd-party DC
power adapters

3
Introduction
The 2-Port Dual-Head HDMI 2.0 KVM with USB 2.0
allows you to control two 4K computers using one set of
keyboard, mouse, microphone, speaker, and displays.
Features
• 2-PortDual-HeadKVMSwitch with the latestHDMI
2.0 (Video), USB Keyboard/Mouse, with Stereo
Out and Mic In. All cables are included
• Supports2 independent (Extended)display outputs
• Supports up to 4K@60Hz resolution
• HDMI 2.0 and DisplayPort 1.2 compliant
• HDCP 2.2 compliant
• Includes a 2-port USB 2.0 hub
• Manual push button and keyboard hot-key device
switching
Installation Requirements
• HDMI or DisplayPort computers
• HDMI display
• HDMI cables (not included)
PackageContents
•2-Port Dual-Head HDMI 2.0 KVM with USB 2.0
•HDMI 2.0 cables (2pcs)
• DisplayPort 1.2 cables (2pcs)
•USB 2.0 cables (2pcs)
•Audio/Mic cables (2pcs)
•Power adapter (Output: 5V/2A)
•User's guide

4
Product Layout
Figure 1: Front Panel Layout
1. Microphone jack: Connects to your microphone
2. Speaker/Headphone jack: Connects to your
speaker/headphone
3. HDMI 2 out: Connects to your HDMI display.
Note: Receives video signal from the DisplayPort
in port.
4. Reset: Press to reset the system
5. HDMI 1 out: Connects to your HDMI display.
Note: Receives video signal from the HDMI in port.
6. USB Type-A (x2): Keyboard and mouse connection
7. USB Type-A (x2): Connects to your USB devices
8. PC 2 select LED: Lights up whe PC 2 is the selected
computer
9. PC 2 active LED: Lights up when PC 2 is up and
running
10. Switch button: Press to switch between the 2
computers
11. PC 1 select LED: Lights up whe PC 1 is the selected
computer
12. PC 1 active LED: Lights up when PC 1 is up and
running

5
Figure 2: Rear Panel Layout
1. Powerjack:Connects to theincluded power adapter
2. Microphone jack: Connects to PC 1's microphone
input jack
3. Audio input jack: Connects to PC 1's speaker/
headphone jack
4. HDMI in: Connects to PC 1's HDMI output port.
Note: Transmits video signal to HDMI out 1 port.
5. USB Type-B: Connects to PC 1's USB Type-A port
6. DisplayPort in: Connects to PC 1's DisplayPort
output port. Note: Transmits video signal to HDMI
out 2 port.
7. Microphone jack: Connects to PC 2's microphone
input jack
8. Audio input jack: Connects to PC 2's speaker/
headphone jack
9. HDMI in: Connects to PC 2's HDMI output port.
Note: Transmits video signal to HDMI out 1 port.
10. USB Type-B: Connects to PC 2's USB Type-A port
11. DisplayPort in: Connects to PC 2's DisplayPort
output port. Note: Transmits video signal to HDMI
out 2 port.
Note: Both HDMI in and DisplayPort in need to be
connected to PCs in order for the Dual Head outputs
(HDMI out 1 and HDMI out 2) to work.

6
Hardware Installation
Front Panel Connection
1. Connect your HDMI displays to the HDMI out of
the KVM using HDMI cables (HDMI cables not
included).
2. Connect your keyboard and mouse to the keyboard
and mouse ports of the KVM.
3. Connectyourmicrophone and speaker/headphone
to the corresponding jacks of the KVM (optional).
4. Connect your USB devices to the USB ports
(optional).
Rear Panel Connection
1. Using the included cables, plug the HDMI and/or
DisplayPort, USB, microphone, and speaker
connectors into their corresponding sockets on the
rear panel of the KVM.
2. At the other end of the cable, plug the HDMI
and/orDisplayPort, USB, microphone, andspeaker
connectors into their corresponding sockets on PC
1, then repeat for PC 2.
3. Plug the included power adapter into the KVM's
power jack, then plug the power adapter into a
reliable power outlet.
4. Power on all connected devices.

7
Connection Diagram
The application diagram shows the most typical input
and output devices used with the KVM.
Front Panel Connections
Rear Panel Connections
Note: Both HDMI in and DisplayPort in need to be
connected to PCs in order for the Dual Head outputs
(HDMI out 1 and HDMI out 2) to work.

8
Operating Instructions
PC Switching
There are two ways to switch between the computers,
manual push button and keyboard hot-key commands.
Manual Push Button
Press the front panel switch button to switch between the
connected computers.
Keyboard Hot-key
1. Press the [Scroll Lock] or [Ctrl] key twice within 5
seconds to enter Hot-key mode. While in Hot-key
mode the keyboard's Scroll Lock LED flashes
continuously or Ctrl LED flashes instead if Scroll
Lock is not available. Note: When entering or
exitingHot-key mode, theKVM's buzzer will sound
an audible beep.
2. Complete the Hotkey command within 10 seconds,
or the process will be aborted.
Hot-key Commands:
A. [Scroll Lock] + [Scroll Lock] + [Enter] OR [Ctrl] +
[Ctrl] + [Enter]: Switches between the connected
computers
B. [Scroll Lock] + [Scroll Lock] + [B] + [0/1] OR [Ctrl]
+ [Ctrl] + [B] + [0/1]: Disables [0] or Enables [1] the
KVM's buzzer.
C. [Scroll Lock] + [Scroll Lock] + [S] OR [Ctrl] + [Ctrl] +
[S]: Enables Auto Scan mode. Press any keyboard
key or the front panel switching button to disable
Auto Scan mode.
D. [Scroll Lock] + [Scroll Lock] + [I] + [5-99] + [Enter]
OR [Ctrl] + [Ctrl] + [I] + [5-99] + [Enter]: Sets Auto
Scan time interval. Default Auto Scan interval is 8
seconds.

9
Specifications
Storage temperature -20 to 60 C
Operating humidity 0 to 80% RH (no condensation)
HDMI compliance HDMI 2.0
DisplayPort compliance DisplayPort 1.2
HDCP compliance HDCP 2.2
Video format Ultra HD, 4K@60Hz (max)
Control Front panel buttons, keyboard hot-key
Power adapter Input: 100-240 VAC, 50/60Hz, 0.4A
Output: 5V, 2A
Dimensions (mm) 167 (W) x 84 (D) x 32 (H)

10
Blank Page

11
Disclaimer
The product name and brand name may be registered
trademarks of related manufacturers. TM and ® may be
omitted on the user's guide. The pictures on the user's
guide are just for reference, and there may be some slight
differences with the actual products.
We reserve the right to make changes without prior
noticeto a productor system describedherein to improve
reliability, function, or design.

Thank you for choosing gofanco
www.gofanco.com