gofanco PRO-PatternGen User manual

PRO-PaernGen
12G/6G/3G/HD/SD-SDI Paern Generator
®
Made in Taiwan
User‘s Guide

®
PRO-PaernGen
Congratulaons for owning a gofanco product. Our products aim to meet all your
connecvity needs wherever you go.
Have fun with our products!
Please read this manual carefully before rst use.
If you need more informaon about our products, please visit www.gofanco.com.
For technical support, please email us at [e-mail].
For drivers/manuals download, please go to hp://www.gofanco.com/download.

®
PRO-PaernGen
Please read all of these instructions carefully before you use the device. Save
this manual for future reference.
The PRO-PatternGen 12G/6G/3G/HD/SD-SDI Pattern Generator has been tested
for conformance to safety regulations and requirements, and has been certied
for international use. However, like all electronic equipments, the PRO-Pattern-
Gen should be used with care. Please read and follow the safety instructions to
protect yourself from possible injury and to minimize the risk of damage to the
unit.
• Follow all instructions and warnings marked on this unit.
• Do not attempt to service this unit yourself, except where explained in this
manual.
• Provide proper ventilation and air circulation and do not use near water.
• Keep objects that might damage the device and assure that the placement of
this unit is on a stable surface.
• Use only the power adapter and power cords and connection cables designed
for this unit.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the po-
wer to the device before cleaning.
1. Safety and Notice
Table of Contents
1. Safety and Notice ..................................................................3
2. Introduction .......................................................................4
3. Features...........................................................................4
4. Specication ......................................................................5
5. Package Contents ..................................................................6
6. Panel Description ..................................................................7
7. Connection Diagram ...............................................................8
8. Notice.............................................................................8
9. Appedix ...........................................................................9
10. Edid LearningWarranty ............................................................11
3

®
PRO-PaernGen
• Supported output resolution
NTSC 525@60, PAL 625@50,
[email protected]/50/59.94/60,
1080i@50/59.94/60,
[email protected]/24/25/29.97/30/50/59.94/60,
[email protected]/24/25/29.97/30/50/59.94/60
• Bit Rate
2.97 Gbps, 2.967 Gbps, 1.485 Gbps, 1.4835 Gbps, 5.94Gbps,
5.934Gbps, 11.88Gbps, 11.868Gbps,270 Mbps
• Video Patterns
100% Color Bars, Borderline, Random Noise, Check Field, Black, Verti-
cal Lines, Black / White alternate elds, Full Grey / Full White, Black to
White Gradient, Random Generator for all still patterns, moving squa-
res White noise, Inverse eect with still pattern, Scrolling Title (see
Appendix for illustrations)
• Save Settings to Memory Option
• ANC Data
EDH (RP-165), SMPTE 352M, SMPTE291M
• Control
By LCM & panel buttons
• Video Output
SDI output (SDI, HD-SDI, 3G-SDI, 6G-SDI, 12G-SDI)
3. Features
The PRO-PatternGen 12G/6G/3G/HD/SD-SDI Pattern Generator is an ad-
vanced SDI pattern generator with multi-format (12G/6G/3G/HD/SD) and
multi-pattern support. Besides still and moving video test patterns, other
features such as audio (SMPTE-291M) are also provided. PRO-PatternGen
can support up to 8 channel AES compliant audio with 48KHz sample rate.
PRO-PatternGen is equipped with four buttons and LCM screen to ease the
control. This device provides a cost eective way to calibrate and test SDI
enable video devices and displays.
2. Introduction
4

®
PRO-PaernGen
5
4.Specications
Item Description
Technical
Role of usage Pattern generator
SDI standards 12G/6G/3G/HD/SD-SDI
Auto SDI rate detection Yes
Supported protocols
SMPTE 259M (270Mbps / 360Mpbs)
SMPTE 292M / HDTV (1.485 & 1.485/1.001Gbps)
SMPTE 424/425M (2.97 & 2.97/1.001Gbps)
SMPTE ST-2081 (5.94&5.94/1.001Gbps)
SMPTE ST-2082 (11.88&11.88/1.001Gbps)
Video support 11.88Gpbs
Audio support 143 / 270 / 1483 / 1485 / 2967 / 2970 / 5934 / 5940 / 11868 / 11880 Mbps
Resolution support
[12G] 4K2K@50/59.94/60
[6G] [email protected]/24, 25, 30
[3G] 1080p@50/59.94/60 (4:2:2)
[HD] 720p@50/59.94/60, 1035i@50/59.94/60, 1080p@24/30,
1080i@50/59.94/60
[SD] [email protected], PAL@50Hz
PCB stack-up SMPTE-292M / 259M / 424M / ST-2081 / ST-2082
Input 75
Output [12G-SDI] up to 50m (165ft) / [6G-SDI] up to 100m (330ft) /
[3G-SDI] up to 200m (660ft)
HDMI Input selection Yes
IR remote control 6-layer board [impedance control — dierential 100 ; single 75 ]
HDMI connector 2x BNC [SDI]
RJ-45 connector 75 interlocking socket
RS-232 connector
Amplitude: Within 800mV <10%Long time jitter <1.0 UI
Rise overshoot: Less than 2% Timing jitter <1.0 UI
Fall overshoot: Less than 2% Alignment jitter <0.2 UI

®
PRO-PaernGen
Mechanical
Housing Metal enclosure
Dimensions
[L x D x H]
Model 340 x 123 x 44mm [1'1" x 4.8" x 1.7"]
Package 494 x 225 x 70mm [1'6" x 8.9" x 2.8"]
Carton 510 x 380 x 252mm [1'7" x 1'2" x 10"]
Weight Model 1181g [2.6 lbs]]
Package 1837g[4 lbs]
Fixedness Wall-mounting case
Power supply 5V 4A DC
Power consumption 12 Watts [max]
Operation temperature 0~40°C [32~104°F]
Storage temperature -20~60°C [-4~140°F]
Relative humidity 20~90% RH [no condensation]
6
• 1x PRO-PatternGen
• 1x 12V power supply unit
• 1x User Manual
5. Package Contents

®
PRO-PaernGen
6. Panel Description
1. POWER LED: Power LED indicator
2. SDI OUTPUT: Connect to a SDI device for SDI signal output either from the
chosen pattern or the SDI source signal
3. Mini-USB: F/W update
4. +12V DC: Connect to a 12V DC power supply unit
5. SDI INPUT: Connect to a SDI source
6. PUSH BUTTON:
7
2 3
5 64
1
Button Function
Menu Trigger the menu operation
Enter Enter the menu item
Up Choose the last menu item
Down Choose the next menu item

®
PRO-PaernGen
7. Connection Diagram
8. Notice
8
1. In HDMI bypass mode, users must be aware of that the jitters coming from HDMI
sources, such as DVD players, may be much higher than typical requirement
according to SMPTE request on HD-SDI signals. This will result in SDI output with
high jitters or even no SDI outputs!
2. Due to the high frequency bandwidth and low jitter requirement of 3G-SDI sig-
nals, it is strongly recommended to use just one SDI OUTPUT with one 75 ohm.
3. The features including new timings and patterns may increase without notice
after the rmware is updated! This may aect the menu items, but will keep the
same framework for users!

®
PRO-PaernGen
9
9. Appendix
ANC Data DID SDID/DBN
352M 0x41 0x01
RP-165-EDH*0xF4 0x00
DataIdenticationWordofAncillaryDataPacket
Built-in Video Patterns
* Data Type 1(SMPTE-291M)

®
PRO-PaernGen
10