Specifications:
Input voltage: 6V to 28V (2S - 6S) VBat
Power Output:5V for Camera @ 0.5A max
Remote software protocol:SmartAudio V2.0
Output Power:14dBm (25mW) 23dBm (200mW*)
Pit mode:
Activate: press button during powered up.
LED: red
Deactivate:
press button during powered up.
LED: blue
( red & blue when unlocked)
Pit mode-> flight mode:
After boot up, press button for 8sec
Channels:
Band A (8ch), B (8ch), E(5ch)
Fatshark 8ch
Race Band 8ch
Low Race Band 8ch **
Power consumption:
25mW: 250mA
200mW: 320mA
Range:Up to 2 km
Video Transmitter
There are categories in the menu, and settings. Pressing the button for 3 seconds will toggle between
categories, pressing it for a short (1 second) press toggles between settings. To enter the menu, hold the
button for 3 seconds. LED colors will signal the state of the menu, for an overview see the following table.
Channel select mode
Enter menu by pressing the button for 3s. Red LED will flash 1 time. Select channels by simple short
presses.
Band select mode
Press button for an additional 3s. Red LED will flash 2 times. Select band by simple short presses.
Unlock & power select mode
(FOR HAM USERS ONLY!) Press button for 20 to 25 seconds. The Red LED will flash 3 times to confirm. You
have unlocked the video transmitter for use with all frequencies (see frequency table below).
NOTE : Unlock only works if you are inside the band selection menu
The power select mode is now accessible. Once unlocked, you can select the power level according to the
table below. To lock the transmitter, go back into band select menu and press the button for 20 to 25
seconds again.
PitMode
While in PitMode you can change channels and set power levels without affecting other pilots signal.
Pit mode function explained HERE
Save and exit
Press button for 3 seconds. Blue LED will turn on, settings are saved and it will exit the menu.
Button menu structure
LED Flash C o des fo r C h an n el,B an d an d P ow er
The TB S U N IFY PRO 5G 8 signals selected channel,band an d pow er levels using a startup sequen ce ofLED
cod es.Th e sam e sequence is also repeated in the m enu to m ake it unified.Firstth e RED LED flashes to
ind icate the item being show n .O ne flash fo r channel,tw o flashes for band,three flashes for pow er level.
Subsequently,the B LU E LED w illin dicate the value.
R ed LED : Indicate item -C hannel,b and or pow er settin g
Blu e LED : Indicate value
For exam ple,Channel6,Band B ,Pow er of 500m W ,w illh ave the follow ing startup LED code:
●1x Red and 6x Blue = C hannel,6
●2x Red and 2x Bl
u
e = Ban d,2 (=B )
●3x Red and 3x Blue = Pow er,3 (= 500m W )
O nce the Video transm itter has successfu lly b ooted up,it w illshow a con stan tB LU E for locked state,and a
con stantRED + BLU E for un locked state.
For reference,see the follow ing m enu table.
Me n u Table
R ED LE D B LU E LED
1x2x3x4x5x6x7x8x
1xC h a n n el12345678
2xB a n dABEA irw aveRaceLow R ace
3xPow er Level25200
Freq u en cy Table
C h a n n el12345678
B a n d A 58655845582558055785576557455725M H z
B an d B 57335752577157905809582858475866M H z
B a n d E57055685566556455885590559255945M H z
A irw a ve57405760578058005820584058605880M H z
R a ce B a n d 56585695573257695806584358805917M H z
Lo w R a ce B a n d *
56215584554755105473543653995362M H z
Pow erLevel25200 m W
