Gold Standard Games Shelti Foos 200 User manual

1
Foos 200 – Assembly Instructions
GS-A-DC-1 / GS-A-DC-1-BK
Thank you for purchasing a Shelti product. All of us at Shelti want to be completely satisfied with your Foos 200 game, so feel free to
contact us for help with the assembly of your product, Shelti parts or other information you may require.
Tools Required:
2- Allen Wrenches (included)
Open End Wrench (included)
Hammer
Phillips screwdriver
Level
Step -1
Remove the following parts from the Pro Foos Box.
Description Part Number Quantity
Right Leg GS-SSR-0 2
Left Leg GS-SSL-0 2
Leg Levelers 201-0074-0 4
Playfield GS-PFA-0 1
Side Apron GS-SAA-0 2
End Apron/Ball Box Assembly GS-EAA-0 2
Goalie Rod Assembly (3 Holes Shorter in Length) ES-GRA-1 2
5- Man Rod Assembly (5 Holes) ES-5RA-1 2
3- Man Rod Assembly (3 Holes Longer in Length) ES-3RA-1 2
2- Man Rod Assembly (2 Holes) ES-2RA-1 2
Rubber Bumpers 203-0002-0 16
Red Soccer Man 201-0064-0 13
Black Soccer Man 201-0068-0 13
Spirol Pin 205-0006-0 26
Score Posts 201-0006-0 4
Score Rods 205-0007-0 2
Red Score Beads 003-0002-0 5
Black Score Beads 003-0003-0 5
#8 x 2” Wood Screws 304-0005-0 4
Spirol Pin Punch 210-0012-0 1
Super Lube Tube 210-0002-0 1
Balls 201-0007-0 3
Rod Block 102-0070-0 1
Field Trim AS-PTA-0 2
Foosball Bearings 201-0011-1 16

2
Step -2
Leg Assembly
•Unbolt legs from the bottom board inside the cabinet with a 9/16” wrench and remove.
•Place legs in the corners as below. Please note that there is a left and right legs so the holes
need to be aligned correctly. The (2) legs with the welded piece of metal at the top of the leg
should be placed on the ball return side. 0
Step – 2
Install The Four Legs. Note Legs Come In
Right and Left. Install As Picture. Also Note
That The Bolts Without Any Nuts Are Used
Through The Side Of The Game Into The Leg
& The Bolts With The Nuts Are Installed
Through The End Of The Game Into The Leg
Step – 3
Once The Four Legs Are Installed The
Game Can Be Flipped Over & The Rods &
Men Can Be Assembled To The Game.

3
STEP 4 – Rods, Bumper and Men Assembly
•Once the table legs are secure, (using two people) pick the table up and turn it over onto its legs.
•Locate the five man rods…. These two rods will be located in the center of the game as illustrated on next page . Note…
The men are designed with a slight press fit onto the rods in order to maximize playability.
oPlace the five man rod through the bushing in one wall… Slide on the first bumper making sure that the larger hole
in the bumper is away from the wall and toward the man. This will allow the bumper to snap onto the shoulder of
the outside man.
oSlide on the five man and the second bumper and slide the rod through the bushing hole in the far wall… Note
that the red and black men face in opposite directions as shown in the illustration (on the next page). In some
cases you may need to add a small amount of lubricant inside the shoulder hole of the man to ease the sliding of
the man onto the rod.
oAlign each man over a hole in the rod and drive in a spirol pin. Note: place the rod block under the rod before
hammering in the spirol pins.
oSnap the bumper onto the shoulder of the outside men. This can be done by pulling/pushing the men into the
side walls until the bumpers are securely seated.
•Repeat these operations for the 3-man, 2-man, and goalie rods. Note: the 3-man and goalie rods both have three holes. The
goalie rod is the shorter rods.
Red Man
Red Man
Three Man Rod – Longer
Than the Goalie Rod
Red Man
Five Man Rod
Red Man
Two Man Rod – Longest
Rod
Goalie Rod – Shorter
Than Three Man Rod
Goalie Rod-shorter
Than Three Man Rod
Two Man Rod – longest
Rod
Black Men
Five Man Rod
Black Men
Three Man Rod – Longer
Than the Goalie Rod
Black Men
Black Men
Ball Return
Insert Field Trim

4
Step 6-Level the Game
•Turn the leg levelers in or out of the leg until the ball rolls true in the play surface.
•For more precise leveling, use a level. Place the level horizontally on the playing surface pointing toward the
goal openings. Be sure all the levelers are screwed all the way in as a starting point. Turn the leg levelers up
equally on one end until you are horizontally level. Then turn your level 90 degrees so it is pointing toward the
ball server holes. Now turn the levelers up on side of the table until you are vertically level.
Step 7- Lubricate the Rods / Bearings
•Push the rod away from you until the bumper hits the opposite wall. Apply two or three drops of lubricate on
the face of the bearing and rod using the Super Lube Tube furnished with the game. Rotate the rod while pulling
the rod toward you to evenly spread the lubricant on the rod. Perform the same operation on the opposite
bearing face and rod. Repeat as needed.

5
Step 8- Rotating the Bushings
•Once a year the bushings should be rotated 180 degrees to assure an even wear of the bushing surface. To
accomplish this rotation remove the rods from the game and push a 7/8” socket head over the bushing fingers
(Drawing – A). Push the bushing out of the hole and rotate the bushing 180 degrees (Drawing – B). Snap the
bushing back into place and return the rod and man to the game.
7/8 " 7/8 " 7/8 "
Drawing – A
Drawing – B
333 Morton Street
.
Bay City, Michigan 48706
Tel: [phone] . Fax: [phone] .www.gold-standard-games.com