Goldmund MIMESIS 37S User manual

USER MANUAL
GOLDMUND MIMESIS 37S
Analog Preamplifier

Thank you for purchasing the Goldmund MIMESIS 37S ANALOG PREAMPLIFIER. Please take
some time to read this manual. It will provide you with useful information to make your pleasure of
listening to the MIMESIS 37S even higher.
INTRODUCTION
GOLDMUND MIMESIS 37S Analog Preamplifier
Goldmund was founded in 1978 and has ever since been dedicated to the accurate reproduction of
sound and image.
At Goldmund, we strive to lead in the creation, development and manufacture of the industry’s
most advanced technologies, including audio and video systems, home-networking and music
distribution.
The guiding principle at Goldmund is to produce a precise sound with the least possible loss of
quality through the different stages. Goldmund will never adopt a technology before it is sufficiently
developed to satisfy the high quality standards we set. This is why Goldmund has often rejected
mainstream technologies and developed its own.

GOLDMUND MIMESIS 37S - Analog Preamplifier - 3
Table of Contents
1 SETTING UP THE MIMESIS 37S 5
2 POWER SUPPLY 9
3 CONTROLS & UTILIZATION 10
4 SOUND QUALITY OPTIMIZATION 11
5 SAFETY FEATURES & MAINTENANCE 12
6 TECHNICAL SPECIFICATIONS 13

GOLDMUND MIMESIS 37S - Analog Preamplifier - 4
W A R N I N G !
No connection or manipulation may be made
before reading these instructions and
observing all safety warnings.
This extremely high quality Preamplifier
possesses new technical features which are or
will become necessary for accurate power
amplification of high quality analog sources.
Observe general electrical safety precautions
particularly with regard to avoiding water,
moisture and heat. To reduce the risk of
electric shock do not remove the covers and
refer servicing to qualified personnel.
The installation instructions must be carried
out in full and the mentioned precautions taken
to provide the satisfaction the Mimesis 37S is
designed to provide and to avoid jeopardizing
personal and equipment safety or impairing
performance.
Nevertheless, in the Mimesis 37S Preamplifier,
Goldmund engineering excellence delivers
extreme performance in a simple and
convenient format that we hope you will enjoy
for many years to come.

GOLDMUND MIMESIS 37S - Analog Preamplifier - 5
1 SETTING UP THE MIMESIS 37S
1.1 PRELIMINARIES
For exacting technicians, musicians, and all high-fidelity music purists who demand the
very best in reproduction, we strongly recommend the use of top quality power amplifiers
with the Mimesis 37S. Most of the analog signal integrity delivered by the preamplifier can
be destroyed by using lower quality amplifiers.
For perfect analog amplification, Goldmund recommends the Goldmund Telos series of
power amplifiers.
The connection between the analog sources and the preamplifier as well as between the
preamplifier and the power amplifiers are also critical. Ultra low reflection interconnect
cables are absolutely mandatory to retain the time integrity that the preamplifier is designed
to provide. In all typical cases Goldmund recommends using the special Goldmund Lineal
interconnect cables.
1.2 UNPACKING
You will find within the two GOLDMUND MIMESIS 37 S transit boxes:
- The Analog Preamplifier.
- The Power Supply Unit.
- Preamplifier to Power Supply cable.
- The mains powercord.
- The remote control and batteries.
- This manual.
Please keep the packaging in case you need to transport the MIMESIS 37S any time in the
future.
This packaging has been designed specifically to protect the MIMESIS 37S in transit. Use
of alternative packaging is likely to result in damage, invalidating warranty cover.

GOLDMUND MIMESIS 37S - Analog Preamplifier - 6
1 SETTING UP THE MIMESIS 37S (Ctd.)
1.3 CHOICE OF PREAMPLIFIER LOCATION
The Goldmund Mimesis 37S preamplifier generates a significant amount of heat. It is
necessary to allow adequate ventilation for proper cooling of the heat sinks. Avoid any
location which is not properly ventilated. Avoid stacking equipment and do not locate the
preamplifier close to equipment that is sensitive to temperature.
The power unit has been especially designed to minimize transformer vibration effects on
the audio circuits. One consequence of this strategy is that the power supply unit is
physically separate, connected by only the 150mm cabling. The power supply and
preamplifier should be located as far apart as the cabling allows. The preamplifier should
ideally not be located above the power supply. The power supply most certainly should
never be located above the preamplifier as this would force transformer vibration
evacuation through the audio circuits on its way to ground.
The power supply also generates a significant amount of heat and the ventilation
requirements noted above also apply.
The preamplifier has been designed with four adjustable conical feet. These are used to
ensure proper vibration transmission to the preamplifier support in order to evacuate all
detrimental vibrations inside the unit, following the famous Goldmund "Mechanical
Grounding" principle. Depending on the flatness of the chosen location, you may have to
adjust one or more of these feet.

GOLDMUND MIMESIS 37S - Analog Preamplifier - 7
1 SETTING UP THE MIMESIS 37S (Ctd.)
1.4 LINE VOLTAGE ADJUSTMENT
Warning! If the line voltage provided is not appropriate as supplied, please consult your
dealer.
ATTENTION: At the 220V position, the Goldmund Mimesis 37S preamplifier will function
properly for main line voltages between 200V and 240V. At the 110V position, the main line
must deliver between 105 and 125V. If your main supply operates out of these tolerances,
please consult your Goldmund dealer.
This fuse is located on the power cord receptacle and can be accessed by raising the cover
using a small screwdriver when the power cord has been removed (ensuring power is
disconnected before handling). Use a 2.5A slow-blow fuse.
Warning! Always ensure that the fuse cover is fitted. Fuses are for fire prevention and do
not protect against risk of electric shock.
1.5 CONNECTIONS
Warning! Always remember that a plug with bared connectors is dangerous if in contact
with a live socket. This appliance must be earthed.
Connect the non-rewireable power cord supplied to the back of the power supply and plug
it into the nearest wall plug. Use only a 3 lugs grounded plug, for safety and noise reasons.
Replacement mains leads can be obtained from your Goldmund retailer.
To get the best sound of the preamplifier, avoid any multiple plugs or extension cords.

GOLDMUND MIMESIS 37S - Analog Preamplifier - 8
1 SETTING UP THE MIMESIS 37S (Ctd.)
1.5 CONNECTIONS (Ctd.)
Warning! Take care to always handle the cable by the connectors. Never twist the cable
excessively or attempt to connect or disconnect the connector by handling the cable body
in place of the connector.
Connect the cabling from the power supply output to the preamplifier input point labeled
“Power”.
Warning! The next stage in setting up your Mimesis 37S is to connect your sources, power
amplifiers and other peripheral devices. All devices should be disconnected from mains
power until safe.
Connect the preamp analog output interconnects to the power amp using the RCA female
sockets labeled “analog outputs”.
Connect the interconnect cables from source devices to the line inputs numbered 1 to 7
labeled ‘IN1’ to ‘IN7’.
Connect tape machines to any inputs and to the Tape output plugs (except INS, no tape
out).

GOLDMUND MIMESIS 37S - Analog Preamplifier - 9
2 POWER SUPPLY
The main POWER switch is located on the back panel of the Goldmund Mimesis 37S
power supply. In regular use, this switch should be left permanently ON and the circuits of
the preamplifier activated or deactivated using the STANDBY ON/OFF.
When the POWER switch is switched ON, the preamp will become operative after few
seconds delay to ensure proper stabilization of all the circuitry and avoid any
unwanted noise. After this delay, the output of the preamplifier is connected to the
power amplifier.
The preamplifier can be powered off by switching the POWER switch to the OFF position. A
special safety circuit switches the preamp to MUTE to avoid any disturbance reaching the
power amplifier and the speakers, even if the preamplifier is disconnected from the mains
supply by accident. However, to optimize the sound quality of the preamplifier and ensure
the reliability, the M37S should remain powered ON continuously and is only deactivated
using the Standby function.

GOLDMUND MIMESIS 37S - Analog Preamplifier - 10
3 CONTROLS & UTILIZATION
The Goldmund Mimesis 37S is designed to capture, control, shape and nurture the fragile
source inputs, supporting adjustment of volume and balance to deliver your desired output
signal. The primary control functions supporting these processes are outlined below.
3.1 STANDBY
To activate stand by mode, use the remote control
3.2 INPUT SELECTION
To select the source you want to listen to, use the left-hand rotary switch or use the remote
control.
3.3 VOLUME ADJUSTMENT
The right-hand volume level adjustment knob (7) is used to adjust VOLUME. If volume is
set to a value of zero, outputs will be muted.
You can use also the remote Control.
3.4 BALANCE ADJUSTMENT
Balance adjustment by using the Remote Control.
3.5 MUTE
Press the MUTE/PWR button (3) to mute output on the Remote Control.

GOLDMUND MIMESIS 37S - Analog Preamplifier - 11
4 SOUND QUALITY OPTIMIZATION
4.1 WARM-UP SONIC EFFECT
If the preamplifier has been left un-powered for some time, the optimum sound quality may
only be attained after many hours. The critical circuits have to warm up to around +55
degrees Celsius (+131 degrees Fahrenheit) before achieving their optimal performances.
This is why Goldmund recommends that the MIMESIS 37S is always powered on.
4.2 ABSOLUTE PHASE
Your Mimesis 37S preamplifier has an absolute phase inverter switch.
Absolute phase optimization can be difficult to achieve with CD's since at the current state
of the technology, the phase coherency of this source is not sufficient to allow a sufficient
difference between the two positions.
Many vinyl recordings are made without care for the absolute phase and different LP's can
have different optimum positions. Trial and error is often therefore necessary.
4.3 GOLDMUND “MECHANICAL GROUNDING”
In the Goldmund Mimesis 22 Signature edition preamplifier, Goldmund has implemented its
renowned construction method to provide an optimized vibration evacuation path.
To get all the benefits of this improvement, the MIMESIS 37S must be located on a very
rigid support, directly coupled to the building. Avoid any decoupling material. If carpet
decouples the preamplifier and ground, use pin-point supports to couple the furniture to the
floor.

GOLDMUND MIMESIS 37S - Analog Preamplifier - 12
5 SAFETY FEATURES & MAINTENANCE
5.1 PROTECTION CIRCUIT
The Goldmund Mimesis 37S preamplifier uses a special protection circuit to protect the
power amplifier and the speakers against a power supply failure or AC shut-down of the
preamplifier.
5.2 MAINTENANCE
To clean your Mimesis use only a soft, clean, dry or slightly damp cloth. Avoid using
domestic cleaning products.
Warning! Always turn the power off before cleaning your preamplifier.
There are no user serviceable parts inside the Mimesis 37S. Unauthorized servicing or
alteration invalidates the manufacturer’s warranty.
All inquiries relating to product servicing and operation should be referred to the local
authorized retailer supplying and supporting your Goldmund equipment.

GOLDMUND MIMESIS 37S - Analog Preamplifier - 13
6 TECHNICAL SPECIFICATIONS
INPUT
•Input impedance: 39 kOhms.
•Maximum input level (balanced) : 9.6 V RMS.
•Maximum input level (unbalanced): 4.8 V RMS.
•Separated input level adjustment for each of the 7 line inputs: -12 to 12 dB.
OUTPUT
•Output impedance: 50 Ohms.
•Maximum output level (balanced) : 19.2 V RMS.
•Maximum output level (unbalanced): 9.6 V RMS.
FREQUENCY RESPONSE
•These values for any level to maximum output level
•+/- 0 dB, 20 - 20 kHz.
•+/- 3 dB, 0.2 – 900kHz.
GROUP DELAY
•Propagation delay <300 ns stable with frequency from DC to 200 kHz.
DISTORTION
With 1 V rms output level, 80 KHz measurement bandwidth, 600 ohms termination
impedance
•- THD unbalanced in to unbalanced out 0.002%
•flat with frequency
•- THD balanced in to balanced out 0.001%
•flat with frequency
•- IMD unbalanced in to unbalanced out 0.002%
•- IMD balanced in to balanced out 0.001%

GOLDMUND MIMESIS 37S - Analog Preamplifier - 14
6 TECHNICAL SPECIFICATIONS (Ctd.)
SPEED
•Slew rate of the amplification stages: 200V/us
•Rise time: < 400 ns.
CROSSTALK
•- Separation: > 105 dB between channels. (20Hz – 20kHz)
NOISE
•Signal-to noise ratio on line input: > 120 dB (0.01 Hz - 10 Mhz).
•Weighted ASA A: > 130 dB.
OPERATING TEMPERATURE
•Room temperature: -30 to +40 degrees Celsius
•Internal temperature: +45 to +70 degrees Celsius
POWER
•Nominal line voltage: 117 or 234 V.
•Input voltage range: +/- 10 %.
•Maximum power consumption: 70 W.
GROUNDING
•Separated ground and earth signal.
•Connection optional between earth and ground to cancel all ground loops.
SAFETY FEATURES
•Automatic switching to MUTING if the AC line drops or is interrupted.
•Automatic protection against tape loops.

GOLDMUND MIMESIS 37S - Analog Preamplifier - 15
6 TECHNICAL SPECIFICATIONS (Ctd.)
FRONT PANEL CONTROLS
•MUTING/POWER switch with Led control.
•VOLUME control.
•BALANCE control.
•RECORD/MENU switch.
•PHASE/EDIT switch.
o7 INPUT CONTROL switches (with Led control).
REAR PANEL CONNECTORS AND CONTROLS
•Power connector.
•Earthing post (yellow-green).
•Output connectors RCA (right and left).
•Output connectors RCA (right and left) for Tape 1 and Tape 2.
•Signal grounding post (black).
•Input connectors RCA (right and left) for Tape and line inputs.
•Link float.
•RS232 Connector.
POWER SUPPLY CONTROLS
•POWER cord socket (3 lugs).
•MAINS FUSE (2.5A slow-blow).
•VOLTAGE SELECTOR 110/220 V.
SIZE AND WEIGHT
Preamplifier
•440 W x 380 D x 90 H. (mm)
Power Supply
•440 W x 280 D x 60 H. (mm).
Total Weight: 15 kg
WARRANTY
•3 years, parts and labor.