Goldmund TELOS 1000 NextGen User manual

USER MANUAL
GOLDMUND TELOS 1000 NextGen
Universal Power Amplifier

Thank you for purchasing the GOLDMUND TELOS 1000 NextGen.
You have acquired the best Universal Power Amplifier ever made for professional and
domestic uses.
Please take some time to read this manual. It will provide you with useful information to
make your pleasure of listening to the TELOS 1000 NextGen even higher.
NTRODUCT ON
GOLDMUND TELOS 1000 NextGen Universal Power Amplifier
Goldmund was founded in 1978 and has ever since been dedicated to the accurate
reproduction of sound and image.
At Goldmund, we strive to lead in the creation, development and manufacture of the
industry’s most advanced technologies, including audio and video systems, home -
networking and music distribution.
The guiding principle at Goldmund is to produce a precise sound with the least possible
loss of quality through the different stages. Goldmund will never adopt a technology before
it is sufficiently developed to satisfy the high quality standards we set. This is why
Goldmund has often rejected mainstream technologies and developed its own.

GOLDMUND T1000 NextGen - Universal Power Amplifier - 3
Table of Contents
1 SETT NG UP THE TELOS 1000 NEXTGEN 5
1.1 PREL M NAR ES 5
1.2 UNPACK NG 5
1.3 AMPL F ER LOCAT ON & COOL NG 6
1.4 L NE VOLTAGE ADJUSTMENTS 7
2CONNECT ONS 8
3AMPL F ER CONTROLS 9
3.1 MANUAL OPERAT ON 9
3.2 NPUT SELECT ON 10
4 SOUND QUAL TY OPT M ZAT ON 11
5MA NTENANCE 12
6TECHN CAL SPEC F CAT ONS 13

GOLDMUND T1000 NextGen - Universal Power Amplifier - 4
W A R N N G
No connection or manipulation must be done
before reading these instructions. Damage to
the amplifier may result if the following
instructions are not consciously understood
and applied.
These extremely high quality amplifiers
possess new technical features which are a
necessity for accurate sound reproduction in
the best audio systems.
Only careful installation and use can provide
the satisfaction you are expecting.
The installation instructions must be carried
out in full and the mentioned precautions
taken to get the expected result and to avoid
impairing the amplifier’s performance.
MPORTANT
PLEASE DO NOT CONNECT ANY CABLES
OR MOVE ANY PARTS BEFORE READING
THE FOLLOWING INSTRUCTIONS.

GOLDMUND T1000 NextGen - Universal Power Amplifier - 5
1 SETT NG UP THE TELOS 1000 NEXTGEN
1.1 PREL M NAR ES
Please read the following instructions very carefully. This high-precision unit will provide the
best signal possible to your speaker thanks to its unique technology.
For exacting technicians, musicians, and all high-fidelity music purists who demand the
very best in musical reproduction, we strongly recommend the use of top quality analog
pre-amplifier or acoustic processor such as the Mimesis 22H or Mimesis 32.5 with analog
or digital input.
The connection between the analog and digital sources and the acoustic processor as well
as between the pre-amplifier and the power amplifiers are critical. Ultra low reflection
interconnect cables are absolutely mandatory in analog and precise impedance SPDIF
cables in digital to keep the time integrity that the acoustic processor is designed to
provide. In all typical cases Goldmund recommends using the special Goldmund Lineal
interconnect and digital cables.
1.2 UNPACK NG
You will find in the GOLDMUND TELOS 1000 NextGen box:
- The amplifier
- The power cord
- This manual
Unpack the above-mentioned parts carefully, keep all packaging for future use.
WARN NG
If you need to return the TELOS 1000
NEXTGEN to the factory or to your local
representative for a warranty repair; please
note that it must be repacked in the
original packaging.
This packaging has been designed specifically
to protect your TELOS 1000 NEXTGEN in
transit. Use of alternative packaging is likely to
result in damage, invalidating warranty cover.

GOLDMUND T1000 NextGen - Universal Power Amplifier - 6
1 SETT NG UP THE TELOS 1000 NEXTGEN (Ctd.)
1.3 AMPL F ER LOCAT ON & COOL NG
The GOLDMUND TELOS 1000 NextGen amplifier, as all high quality amplifiers generates
a significant amount of heat when driven at high levels and must be vented properly. It is
mandatory to allow a proper cooling of the heat sinks. Do not put temperature sensitive
equipment on top of the amplifier.
Due to its weight, and to maximize the effect of the built-in "Mechanical Grounding"
construction, the TELOS 1000 NextGen is better located on the floor. Other very strong
supports can be used if they offer rigid transmission to the floor.
The TELOS 1000 NextGen is built on four very hard conical feet to ensure proper vibration
transmission to the amplifier support. This evacuates all detrimental vibrations inside the
amplifier, following the famous GOLDMUND "Mechanical Grounding" principle.
If you use more than one TELOS 1000 NextGen at any location, you may decide to stack
them. Be careful that the conical feet of the top amp are inserted properly on the top of the
steel bars of the amplifier located below. You may stack up to 3 amps provided extra care
is taken to ensure proper air circulation vents the rear heat-sinks.
Depending on the flatness of the surface where the amplifier will be located, you will adjust
the four round flat feet of the amplifier to allow full contact of the points with the support.

GOLDMUND T1000 NextGen - Universal Power Amplifier - 7
1 SETT NG UP THE TELOS 1000 NEXTGEN (Ctd.)
1.4 L NE VOLTAGE ADJUSTMENTS
A voltage selector is provided inside the amplifier.
If your line voltage is not adapted to the voltage indicated on the serial plate of the
amplifier, please consult your local GOLDMUND dealer for internal adjustment.
ATTENT ON
On the 220V position, the GOLDMUND TELOS 1000 NextGen amplifier will function
properly for main line voltage between 211V and 257V. On the 110V position, the main line
must deliver between 105 and 129V. If your main line is usually out of these tolerances,
please consult your GOLDMUND dealer.
Please check the value of the main line fuse. This fuse is located on the back panel of the
amplifier, above the two power cord receptacles.
Use a 4A delayed fuse for 220V area and 8A delayed fuse for 110V area.

GOLDMUND T1000 NextGen - Universal Power Amplifier - 8
2 CONNECT ONS
Connect the power cord to the back of the amplifier and plug it into the nearest wall plug.
Use only a 3 lugs grounded plug, for safety reasons. To get the best sound from the
amplifier, avoid any multiple plug or extension cord.
If used with an analog signal, connect the interconnect between the preamp and each
power amp and set the TELOS 1000 NextGen in analog mode. You may either use the
RCA female socket or the XLR. The XLR socket, especially useful in professional
installations, is wired as follows:
1. Grounding, Shielding
2. Hot
3. Cold
ATTENT ON
If you want to use a symmetrical 4 wire cable, never maintain the ground/earth
switch to "Float" or you may damage your amplifier.
When used with a digital input signal, connect the digital input cable to the digital input and
switch the amplifier into the digital mode. Since a digital Spdif cable carries 2 channels you
may link the digital output to the next amplifier to transfer the second channel.
Connect the speaker cable to one of the red and black terminals in the back of the
amplifier, or, if you use a Goldmund High Definition speaker cable, you can connect directly
from the speaker cable to one of the coaxial plugs on the back panel of the amplifier,
bypassing the amplifier adapter module of the speaker cable.
The 2 separate outputs (both 5 way post and coaxial) are connected internally in parallel.
They are provided to facilitate the connection in bi-wiring systems.
You may notice that the ground of the input plug and the black speaker terminal are the
same polarity. The amplifier is non-inverting in phase.

GOLDMUND T1000 NextGen - Universal Power Amplifier - 9
3 AMPL F ER CONTROLS
3.1 MANUAL OPERAT ON
On the front plate of the GOLDMUND TELOS 1000 NextGen amplifier you will find only two
POWER keys.
The two POWER keys have to be activated simultaneously to power the amplifier on.
This security feature is provided to avoid accidental POWER ON or POWER OFF.
As soon as the amplifier is connected to mains power, the orange indicator on the front
panel will blink briefly every 3 seconds.
Push both buttons of the front panel simultaneously in order to turn on the amplifier.
As soon as the amplifier is fully powered the green indicator will light steadily and the menu
will be displayed.
If the digital input is not used, the orange led is off, showing there is no lock and the
amplifier remains muted until a lock is found. The led will turn on as soon as the TELOS
1000 NextGen receives a digital input.
In analog mode (XLR & RCA) the orange led is always on.
By pressing the right key once, the amplifier is put in Operate mode “Unmute”, by pressing
the right key once again, the amplifier returns to the menu “Muted” state.
The amp may be POWERED OFF by pressing the two POWER keys simultaneously at
anytime.
Power On Process:
•Progressive charge of high power
capacitors to limit peak current on
AC line.
•Switch on high power supply on
output stage.
•Wait stabilization of high power
supply.
Power Off Process:
•Push both buttons simultaneously
in order to turn off the amplifier.
•As soon as the amplifier's
capacitor bank is fully discharged
the yellow indicator will blink briefly
every 3 seconds.

GOLDMUND T1000 NextGen - Universal Power Amplifier - 10
3 AMPL F ER CONTROLS (Ctd.)
3.2 NPUT SELECT ON
The menu is only available from the main screen when the amplifier is muted.
Use the left button (2) to enter the menu and cycle through the menu items.
Once the wanted menu item is shown on the screen, push the right button (1) to cycle
through the available settings of the given item.
Once the wanted setting is chosen, push the left button (2) to confirm your choice.
Push the left button again to continue to the next menu item or get back to the main
screen.
- Button 1: to navigate into the menu to select the digital left/right, analog input (RCA &
XLR) and brightness adjustment.
- Button 2: to select the input and mute/unmute the amplifier
On the input selection menu, one press on the button 2 moves the Input selection to the
right as follow: