Gomax EX-57IP-W User manual

HDMI over IP Multicast System
with PoE support
User Manual
Safety and Notice
The EX-57IP-W HDMI over IP Mulcast System with PoE
support has been tested for conformance to safety regulaons
and requirements, and has been cerfied for internaonal use.
However, like all electronic equipments, the EX-57IP-W should
be used with care. Please read and follow the safety instrucons
to protect yourself from possible injury and to minimize the risk
Follow all instrucons and warnings marked on this unit.
Do not aempt to service this unit yourself, except where
explained in this manual.
Provide proper venlaon and air circulaon and do not use near
water.
Keep objects that might damage the device and assure that the
placement of this unit is on a stable surface.
Use only the power adapter and power cords and connecon
cables designed for this unit.
Do not use liquid or aerosol cleaners to clean this unit. Always
unplug the power to the device before cleaning.
CONNECTION DIAGRAM
Definition of IR Earphone Jack
IR PASS-THROUGH
IR Extenders
IR ReceiverIR Blaster
IR ReceiverIR Blaster
IR Sockets
IR BLASTER: plug in the IR blaster to emit all IR command signals
received from the IR receiver from the other end to control the devices
corresponding to the IR signals.
IR RECEIVER: plug in the IR receiver to receive all IR command signals
from the IR remote controls of the corresponding devices.
!
Incorrect placement of IR Blaster and Receiver may result in the
failure of the IR extenders. Please check carefully before plugging in
the IR extender to the respecve IR sockets. Warranty will not cover
the damage.
You can buy any IR extension cables in the market that are
compable to the definion of the IR sockets for the matrix if
necessary for replacement use. However, IR cables longer than 2m
(6-) may not work.
1. IR Signal
2. Grounding
1. IR Signal[20-60 kHz]
2. Grounding
3. Power
i
Transmitter Receiver
WARRANTY
The SELLER warrants the EX-57IP-W HDMI over IP
Mulcast System with PoE support free from defects in the
material and workmanship for 1 year from the date of purchase
from the SELLER or an authorized dealer. Should this product fail
to be in good working order within 1 year warranty period, The
SELLER, at its opon, repair or replace the unit, provided that the
unit has not been subjected to accident, disaster, abuse or any
unauthorized modificaons including stac discharge and power
surge. This warranty is offered by the SELLER for its BUYER with
direct transacon only. This warranty is void if the warranty seal
on the metal housing is broken.
Unit that fails under condions other than those covered
will be repaired at the current price of parts and labor in effect at
the me of repair. Such repairs are warranted for 90 days from
the day of reshipment to the BUYER. If the unit is delivered by
mail, customers agree to insure the unit or assume the risk of
loss or damage in transit. Under no circumstances will a unit be
accepted without a return authorizaon number.
The warranty is in lieu of all other warranes expressed or
implied, including without limitaons, any other implied
warranty or fitness or merchantability for any parcular
purpose, all of which are expressly disclaimed.
Proof of sale may be required in order to claim warranty.
Customers outside Taiwan are responsible for shipping charges
to and from the SELLER. Cables and power adapters are limited
to a 30 day warranty and must be free from any markings,
scratches, and neatly coiled.
The content of this manual has been carefully checked and
is believed to be accurate. However, The SELLER assumes no
responsibility for any inaccuracies that may be contained in this
manual. The SELLER will NOT be liable for direct, indirect,
incidental, special, or consequenal damages resulng from any
defect or omission in this manual, even if advised of the
possibility of such damages. Also, the technical informaon
contained herein regarding the EX-57IP-W features and
specificaons is subject to change without further noce.

The EX-57IP-W HDMI over IP Mulcast System with PoE
support boosts up your video/audio transmission distance up to
100m(330) in HDTV 1080p format. With cost effecve Ethernet
cable, users can readily extend HDTV sources from DVD players,
Blu-ray Disc player, PS3, PC, and any other HDMI sources
broadcasng to distant display monitors including HDMI or DVI
enabled TV sets or LCD PC monitors. Besides EX-57IP-W is HDCP
compliant, and supports PoE, IR and RS-232 pass-through path.
With broadcasng management soware and Gigabit
Ethernet network switch (supported IGMP), EX-57IP-W is a
complete HD video broadcasng soluon for digital signage. It
can transmit Full HD 1080p HDMI video broadcasng over IP
network. The broadcasng format can be Point to Point, Point to
Many, and Mul-Casng. Mul-casng is based on Managed
Gigabit Switch with 802.1Q VLAN funcon which provides
control remotely, so mul video and source allowed and
supported.
Supports resoluon up to 1080p60
HDMI v1.3 compliant
HDCP 1.4 compliant
Supports audio extracon via stereo & toslink on both
transmier and receiver
Supports POE funcon
Sample rates of 32~192KHz and sample sizes of 16~24 bits
Transmits video and audio signal over a network
Supports HDMI loop through
Easy distribute mul scalable Full HD video to different
locaons based on IP network
Supports full frequency IR signal pass-through from 20KHz
to 60KHz
Full Duplex RS-232 control up to 115,200 bps through
connector
Up to 1,063 Groups Mul-Casng
Encoder: MPEG4 AVC part10 & MPEG audio layer (1/2/3) &
Planar: 4:2:0 (YUV)
Supports Protocol: IP, TCP, UDP, RTP, IPv4, DHCP, HTTP,
IGMP, ICMP, MULTICAST, UNICAST
Ethernet: 10/100 BASE-T RJ45
Supports Streaming Bit rate up to 15Mbps (+-10%)
Enable Protocol compable with any soware player (such
as VLC® or others)
Latency: 720P60: 190~240ms / 1080P60: 380~430ms.
Wall mounng housing design for easy and robust installaon
1x EX-57IP-W-TX
1x IR blaster cable
1x User Manual
INTRODUCTION SPECIFICATIONS
FEATURES
PACKAGE CONTENTS
PANEL DESCRIPTIONS
EX-57IP-W[TX]
1x EX-57IP-W-RX
1x IR receiver cable
1x User Manual
EX-57IP-W[RX]
PANEL DESCRIPTIONS
Transmitting unit ► EX-57IP-W[TX]
+5V DC: Connect to 5V DC power supply(optional)
RS-232: Connect to PC serial port with a DSUB-9 male-male cable here
Mini USB: for F/W update
S/PDIF Output (TOSLINK)
Stereo Output (3.5mm)
HDMI IN: Connects to a HDMI source with a HDMI male-male cable
IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of
IR blaster
LED Indicator: Power and signal LED indicator
HDMI LOOPOUT: Connect to a HDMI display with a HDMI male-male cable
Dip Switch: Video channel setting (Please refer to “Notes”)
HDMI Signal OUT: RJ-45 Network connector
7 8 9
10 11
1 2 3 4 5 6
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Receiving unit ► EX-57IP-W[RX]
LED Indicator: Power and signal LED indicator
IR Receiver: Infrared 3.5mm socket for plugging in the extension cable
of IR receiver
HDMI OUT: Connect to a HDMI display with a HDMI male-male cable.
S/PDIF Output (TOSLINK)
Stereo Output (3.5mm)
+5V DC: Connect to 5V DC power supply(optional)
RS-232: Connect to PC serial port with a DSUB-9 male-male cable here
Mini USB: for F/W update
HDMI Signal IN: RJ-45 Network connector
17 18 19 2012 13 14 15 16
12.
13.
14.
15.
16.
17.
18.
19.
20.
Notes: TX group ID dip-switch setting
1. For ID=1~63, please refer the table below to set up (Hardware control)
2. For ID=64~1063, please adjust the DIP switch to ID=0, and the real ID can
be decided by the external software (Software control)
ID Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 ID Pin1 Pin2 Pin3 Pin4 Pin5 Pin6
0 ↓↓↓↓↓↓ 32 ↓↓↓↓↓↑
1 ↑↓↓↓↓↓ 33 ↑↓↓↓↓↑
2 ↓↑↓↓↓↓ 34 ↓↑↓↓↓↑
3 ↑↑↓↓↓↓ 35 ↑↑↓↓↓↑
4 ↓↓↑↓↓↓ 36 ↓↓↑↓↓↑
5 ↑↓↑↓↓↓ 37 ↑↓↑↓↓↑
6 ↓↑↑↓↓↓ 38 ↓↑↑↓↓↑
7 ↑↑↑↓↓↓ 39 ↑↑↑↓↓↑
8 ↓↓↓↑↓↓ 40 ↓↓↓↑↓↑
9 ↑↓↓↑↓↓ 41 ↑↓↓↑↓↑
10 ↓↑↓↑↓↓ 42 ↓↑↓↑↓↑
11 ↑↑↓↑↓↓ 43 ↑↑↓↑↓↑
12 ↓↓↑↑↓↓ 44 ↓↓↑↑↓↑
13 ↑↓↑↑↓↓ 45 ↑↓↑↑↓↑
14 ↓↑↑↑↓↓ 46 ↓↑↑↑↓↑
15 ↑↑↑↑↓↓ 47 ↑↑↑↑↓↑
16 ↓↓↓↓↑↓ 48 ↓↓↓↓↑↑
17 ↑↓↓↓↑↓ 49 ↑↓↓↓↑↑
18 ↓↑↓↓↑↓ 50 ↓↑↓↓↑↑
19 ↑↑↓↓↑↓ 51 ↑↑↓↓↑↑
20 ↓↓↑↓↑↓ 52 ↓↓↑↓↑↑
21 ↑↓↑↓↑↓ 53 ↑↓↑↓↑↑
22 ↓↑↑↓↑↓ 54 ↓↑↑↓↑↑
23 ↑↑↑↓↑↓ 55 ↑↑↑↓↑↑
24 ↓↓↓↑↑↓ 56 ↓↓↓↑↑↑
25 ↑↓↓↑↑↓ 57 ↑↓↓↑↑↑
26 ↓↑↓↑↑↓ 58 ↓↑↓↑↑↑
27 ↑↑↓↑↑↓ 59 ↑↑↓↑↑↑
28 ↓↓↑↑↑↓ 60 ↓↓↑↑↑↑
29 ↑↓↑↑↑↓ 61 ↑↓↑↑↑↑
30 ↓↑↑↑↑↓ 62 ↓↑↑↑↑↑
31 ↑↑↑↑↑↓ 63 ↑↑↑↑↑↑
Technical
Role of usage
HDMI compliance
HDCP compliance
Video bandwidth
Video support
HDMI over UTP
transmission [24-bit]
Audio support
Input TMDS signal
Input DDC signal
ESD protection
PCB stack-up
IR pass-thru
RS-232 support
Input
Output
HDMI source control
IR remote control
HDMI connector
RJ45 connector
3.5mm connector
Model Name EX-57IP-W
EX-57IP-W[Tx]
Transmitter [TX]
EX-57IP-W[Rx]
Receiver [TX]
HDMI
Yes
Single-link 225MHz [6.75Gbps]
Up to 1080p60
Full HD (1080p)-100m(330ft) [CAT.X]
stereo digital audio
1.2 Volts [peak-to-peak]
5 Volts [peak-to-peak, TTL]
[1] Human body model - ±19kV [air-gap discharge] & ±12kV [contact discharge]
[2] Core chipset - ±8kV
4-layer board [impedance control — differential 100Ω; single 50Ω]
Yes
Yes
1x HDMI
1x RJ45 +1x HDMI +
2x 3.5mm + 1x TOSLink
1x HDMI +
1x 3.5mm + 1x TOSLink
1x RJ45 + 1x 3.5mm
Controllable via IR pass-through from RX to TX with IR extenders
Electro-optical characteristics: = 25° / Carrier frequency: 20-60kHz
Type A [19-pin female]
WE/SS 8P8C with 2 LED indicators
IR blaster, IR receiver, & Stereo out
Wall-mounting case with screws
PoE (Power over ethernet)
5 Watts
0~40°C [32~104°F]
-20~60°C [-4~140°F]
20~90% RH [no condensation]
τ
Housing Metal enclosure
Dimensions
[L x W x H]
Weight
Fixedness
Power supply
Power consumption
Operation temperature
Storage temperature
Relative humidity
Model
Package
Carton
Model
Package
135 x 97 x 28mm[5.3" x 3.8" x 1.1"] 133 x 96 x 27mm[5.2" x 3.8" x 1"]
264 x 170 x 77mm[10.3" x 6.7" x 3"]
430 x 358 x 291mm[1'4" x 1'2" x 11.5"]
264 x 170 x 77mm[10.3" x 6.7" x 3"]
430 x 358 x 291mm[1'4" x 1'2" x 11.5"]
428g [15oz]
652g [1.4lbs]
428g [15oz]
652g [1.4lbs]
Mechanical