Good Display GDE060BAFL-T User manual

6.0 inch
E-paper Display Series
GDE060BAFL-T
Dalian Good Display Co., Ltd.
GOOD DISPLAY

Product Specifications
Customer Standard
Description 6.0” E-PAPER DISPLAY with
Touch Panel and Frontlight
Model Name GDE060BAFL-T
Date 2019/04/26
Revision 2.0
Design Engineering
Approval Check Design
No.17 Gonghua Street, Shahekou District, Dalian 116021 China
Tel: [phone] Fax: [phone]-810
Email: [email protected]
Website: www.e-paper-display.com
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY

Contents
1 General Description ........................................................................ 5
2 Features ....................................................................................... 5
3 Application .................................................................................... 5
4 Pin Assignment. ............................................................................. 6
5 Electrical Characteristics .................................................................. 7
6 Power On/Off Sequence ................................................................... 10
7 Mechanical Specifications ................................................................. 11
8 Optical Characteristics ..................................................................... 13
9 Handling, Safety and Environment Requirements ................................. 14
10 Reliability Test .............................................................................. 15
11 Block Diagram .............................................................................. 16
12 Packaging .................................................................................... 17
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY

Version Content Date Producer
1.0 New Release 2019/04/26
GDE060BAFL-T
GOOD DISPLAY

1 General Description
GDE060BAFL-T is an Active Matrix Electrophoretic Display(AM EPD) with touch panel and
frontlight, High-Resolution AM TFT Black/White display module which can be used in portable
electronic devices, such as E-book Reader.
The module is a TFT-array driving electrophoretic display, with integrated circuits including
source and gate drivers. The resolution of the module is 600×800（SVGA），and the active area
is 6 inch diagonal.
2 Features
With Touch Panel and Frontlight
600×800 display
White Reflectance above 35%(0 minute)
Contrast Ratio above 8:1(0 minute)
3:4 aspect ratio
Wide viewing angle
Ultra low power consumption
Reflective mode
Bi-stable display
Commercial temperature range
Landscape, portrait modes
Hard-coat antiglare display surface
3 Application
E-book reader
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY

4 Pin Assignment
No. Pin Name Description
1 VNEG Negative power supply source driver
2 VGL Negative power supply gate driver
3 VSS Ground
4 NC NO Connection
5 NC NO Connection
6 VDD Digital power supply drivers
7 VSS Ground
8 CLK Clock source driver
9 VSS Ground
10 LE Latch enable source driver
11 OE Output enable source driver
12 SPH Start pulse source driver
13 D0 Data signal source driver
14 D1 Data signal source driver
15 D2 Data signal source driver
16 D3 Data signal source driver
17 D4 Data signal source driver
18 D5 Data signal source driver
19 D6 Data signal source driver
20 D7 Data signal source driver
21 VCOM Common connection
22 NC NO Connection
23 NC NO Connection
24 NC NO Connection
25 NC NO Connection
26 VSS Ground
27 NC NO Connection
28 CPV Shift clock input
29 STV Start pulse gate driver
30 NC NO Connection
31 VBORDER Border connection
32 VSS Ground
33 VPOS Positive power supply source driver
34 VGH Positive power supply gate driver
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY

5 Electrical Characteristics
5.1 Module Interface Description
This module can be driven by ASIC AVT6201A Timing Controller(T-Con).
5.2 Module DC Characteristics
Parameter Symbol Conditions Min Typ Max Unit
Signal ground VSS - 0 - V
Logic Voltage supply VDD 3.0 3.3 3.6 V
IVDD VDD=3.3V - 3.0 - mA
Gate Positive supply
VGH 21 22 23 V
IVGH - 0.35 - mA
Gate Negative supply
VGL -21 -20-19 V
IVGL - -3.0 - mA
Source Positive supply
VPOS 14.6 15 15.4 V
IPOS VPOS=15V - 20 - mA
Source Negative supply
VNEG -15.4 -15-14.6 V
INEG VNEG=-15V - -20 - mA
Asymmetry source VASYM VPOS+VNEG -800 80 mV
Common voltage
VCOM -2.5 Adjusted -1.5V
ICOM - -1.5 - mA
Standby power module PSTBY - 0.4 mW
Typical power module PTYP - 600 1100 mW
Operating temperature 0 50 ℃
Storage temperature -20- 70 ℃
Maximum image
update time at 25℃ 960 1200 ms
Notes:
1. The maximum power and maximum current are specified for the worst case power
consumption.
2. The typical power is measured when “typical images” are displayed.
3. The standby power is the consumed power when the module controller is in standby
mode.
4. The listed electrical/optical characteristics are only guaranteed under the controller &
waveform provided by . GoodDisplay
Humidity range -70 %RH
- 40
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY

5.3 Module AC Characteristics
Note:VDD=3.0V to 3.6V, unless otherwise specified
Parameter Symbol Min. Typ. Max. Unit App Pin
Clock frequency fcpv - - 200 kHz
CPV Clock CPV high time tCPVh 0.5 - - us
Clock CPV low time tCPVl 0.5 - - us
Data setup time tSU 100 - - ns CPV
STV
Data hold time tH 300 - - ns
Clock CLK cycle time tclk 40 - - ns
Below
table
D0 .. D7, SPH setup time tsu 8 - - ns
D0 .. D7, SPH hold time th 8 - - ns
LE on delay time tLEdly 40 - - ns
LE high-level pulse width tLEw 40 - - ns
LE off delay time tLEoff 40 - - ns
SHR setup time tMsu 100 - - ns
SHR hold time tMh 10 - - ns
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY

Clock & Data Timing
tclk
tsu th
D0~D7, SPH
CLK
Output Latch/Control Signals
tLEw
tMh
tMsu
tLEdly tLEoff
CLK
SPH
LE
SHR
tCPVh
tCPVl
tSU tH
CPV
STV
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY

6 Power On/Off Sequence
To prevent the device from damage due to latch up, the power on/off sequence shown below
must be followed. When power on: VDD -> VGL -> VNEG/VGH/VPOS -> Vcom
When power off: Vcom -> VNEG/VGH/VPOS -> VGL -> VDD
VGH
VPOS
VDD
VNEG
VGL
Logic Signal Input
VSS
Vcom
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY

7 Mechanical Specifications
7.1 Dimension
PARAMETER VALUE UNIT Remark
Display Resolution 600×800 dots
Active Area Dimensions
Horizontal
Vertical
90.6
122.4
mm
mm
Screen Size 6.0（ 3:4 diagonal） Inch
Pixel Pitch
Horizontal
Vertical
0.151
0.153
mm
mm
Pixel Configuration Rectangle
Overall Dimensions
Width
Height
Thickness
101.8
138.4
2.40
mm
mm
mm
Mass of the Module 51±0.5 g
7.2 Electrical Connector
SERVICE CONNECTOR NUMBER OF PINS
Interface FPC pitch=0.5mm 34
7.3 Mechanical Drawing of EPD Module
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY




7


 Vl. 0






文件编号：
F




横向10: 1
1: 1
E

 




 


 
  
  

Nd。。－
N．。忖。的
时．OG－－
N．O忖O∞．O




前扭国
 P[饨’，士也回
2．SN．O料o．NS
（写丘）时－O。由·何时间
20）时－O料。由·由2
〈J民）N－D。∞·国内H
（旦）N－O料o－HS
（白岛）N．D料$62
Nd。。－E
N－－忖。·口
时．O．
Nd忖O∞．H


B
6

8


3

 A
DRAWN BY: 绘 图：
CHECKED BY: 审 核：
APPROVED BY: 批 准：
Standard tolerance: 公 差：
PRODUCT MODEL: 产品型号：
CUSTOMER ID: 客户编号：
DATE: 日 期：
WEBSITE: 网 址：
投影方式:第三角投影法
VIEW:
UNITS: 单 位：
SCALE: 比 例：
mm
1:1
大连佳显电子有限公司
DALIAN GOOD DISPLAY CO., LTD.
客户确认签字
：
TP Pin define
1 2 3 4 5 6 7 8
GND
VDD
RST
INT
SDA
SCL
NC NC
GDE060BAFL-T
2019.04.12
www.e-paper-display.com
GDE060BAFL-T
Technical Parameters： 1. Structure:F+F 2. Channels:16*22 IC:FT5436 3. Power Supply: 2.8V-3.6V 4. Transmittance: ≥83% 5. Surface hardness: ≥2H 6. Working Temp&Humidity: 0℃~+50℃ 7. Storage Temp&Humidity: -20℃~+70℃，40%RH~70%RH 8. Tolerances unless otherwise specification±0.2mm
GOOD DISPLAY

8. Optical Characteristics
Parameter Conditions
Values
Units Notes
Min. Typ. Max
White Reflectivity 0 minute 35 - - %
Contrast Ratio (CR) 2 minute 8:1 - - 1
Image Update Time:
GC16(T=0℃) - 1500 1600
ms
GC16(T=25℃) - 960 1200
GC16(T≥35℃) - 760 960
DU (T=0℃) - 500 540
DU(T≥20℃) - 300 360
(Tamb=25℃, fv=50Hz. Measurements are made with Eye-One Pro Spectrophotometer.)
Notes:
1. CR=Surface Reflectance with all white pixel/Surface Reflectance with all black pixels
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY

9. Handling, Safety and Environment Requirements
Warning
The display glass may break when it is dropped or bumped on a hard surface. Handle
with care. Should the display break, do not touch the electrophoretic material. In case
of contact with electrophoretic material, wash with water and soap.
Caution
The display module should not be exposed to harmful gases, such as acid and alkali
gases, which corrode electronic components.
Disassembling the display module can cause permanent damage and invalidates the
warranty agreements.
Observe general precautions that are common to handling delicate electronic components.
The glass can break and front surfaces can easily be damaged. Moreover the display is
sensitive to static electricality and other rough environmental conditions.
Precautions
(1) Do not apply pressure to the EPD panel in order to prevent damaging it.
(2) Do not connect or disconnect the interface connector while the EPD panel is in
operation.
(3) Do not touch IC bonding area. It may scratch TFT lead or damage IC function.
(4) Please be mindful of moisture to avoid its penetration into the EPD panel, which
may cause damage during operation.
(5) If the EPD Panel / Module is not refreshed every 24 hours, a phenomena known as
“Ghosting” or “Image Sticking” may occur. It is recommended to refreshed the
ESL /EPD Tag every 24 hours in use case. It is recommended that customer ships or
stores the ESL / EPD Tag with a completely white image to avoid this issue
(6) High temperature, high humidity, sunlight or fluorescent light may degrade the
EPD panel’s performance. Please do not expose the unprotected EPD panel
to high temperature, high humidity, sunlight, or fluorescent for long periods of
time.
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY

10. Reliability Test
No. TEST CONDITION METHOD REMARK
1
High-
Temperature
Operation
T = +50°C, RH = 30% for
168 hrs
IEC 60
068-2-2Bp
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
2
Low-
Temperature
Operation
T = 0°C for 168 hrs IEC 60
068-2-2Ab
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
3
High-
Temperature
Storage
T = +70°C, RH=23%
168 for hrs
IEC 60
068-2-2Bp
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
4
Low-
Temperature
Storage
T = -25°C for 168 hrs IEC 60
068-2-1Ab
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
5
High-
Temperature,
High-Humidity
Operation
T = +40°C, RH = 90%
for 168 hrs
IEC 60
068-2-3CA
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
6
High
Temperature,
High- Humidity
Storage
T = +60℃, RH=80%
for 168 hrs
IEC 60
068-2-3CA
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
7 Thermal Shock 1 cycle:[-25℃
30min]→[+70 ℃ 30 min] :
50cycles
IEC 60
068-2-14
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
8 Package
Vibration
1.04G, Frequency:10~500Hz
Direction: X,Y,Z
Duration:1 hours in each
direction
Full packed
for
shipment
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
9 Package
Drop Impact
Drop from height of 122 cm
on concrete surface.
Drop sequence: 1 corner,
3edges, 6 faces
One drop for each
Full packed
for
shipment
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
10
Electrostatic
Effect
(non-operating)
Machine model
+/- 250V, 0Ω,
200pF
IEC 62179,
IEC 62180
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
11 Stylus Tapping
POLYACETAL Pen:Top
R0.8mm Load: 200gf
Speed: 30times/min
Total 13,500times
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY

10. Reliability Test
No. TEST CONDITION METHOD REMARK
1
High-
Temperature
Operation
T = +50°C, RH = 30% for
168 hrs
IEC 60
068-2-2Bp
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
2
Low-
Temperature
Operation
T = 0°C for 168 hrs IEC 60
068-2-2Ab
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
3
High-
Temperature
Storage
T = +70°C, RH=23%
168 for hrs
IEC 60
068-2-2Bp
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
4
Low-
Temperature
Storage
T = -25°C for 168 hrs IEC 60
068-2-1Ab
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
5
High-
Temperature,
High-Humidity
Operation
T = +40°C, RH = 90%
for 168 hrs
IEC 60
068-2-3CA
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
6
High
Temperature,
High- Humidity
Storage
T = +60℃, RH=80%
for 168 hrs
IEC 60
068-2-3CA
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
7 Thermal Shock 1 cycle:[-25℃
30min]→[+70 ℃ 30 min] :
50cycles
IEC 60
068-2-14
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
8 Package
Vibration
1.04G, Frequency:10~500Hz
Direction: X,Y,Z
Duration:1 hours in each
direction
Full packed
for
shipment
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
9 Package
Drop Impact
Drop from height of 122 cm
on concrete surface.
Drop sequence: 1 corner,
3edges, 6 faces
One drop for each
Full packed
for
shipment
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
10
Electrostatic
Effect
(non-operating)
Machine model
+/- 250V, 0Ω,
200pF
IEC 62179,
IEC 62180
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
11 Stylus Tapping
POLYACETAL Pen:Top
R0.8mm Load: 200gf
Speed: 30times/min
Total 13,500times
At the end of the test, electrical,
mechanical, and optical
specifications shall be satisfied.
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY

12. Packaging
www.e-paper-display.com 6.0 inch Series
GDE060BAFL-T
GOOD DISPLAY