Goodmans CDMP3722K User manual

support@71 230177
[e-mail]

1. Open the battery compartment cover and insert two of the recommended rechargeable
batteries (NI-MH TYPE 1.2V 1200mAH), ensuring polarity markings are observed.
All batteries must be of rechargeable
NI-MH type, otherwise the batteries
may explode suitable or leak.
2. Plug in the AC adaptor(4.5V 600mA)( Not Included).
3. In power off mode, press the STOP / RECHARGEbutton once, the display will show
“ C ” ( The battery mark will flash), and the charging will start.
* Press the STOP / RECHARGE button again to stop the charging, the display will
disappear.
4. When charging is full or after 20 hours, the charging will stop automatically, and the
display will disappear.
5. If the operating time decreases drastically even when the rechargeable NI-MH batteries are
properly recharged, purchase a new set of rechargeable NI-MH batteries.
6. When charging for the first time or after a long time, playing time may be reduced. In this
case, charge and discharge the batteries several times.
Important: Never recharge the non-rechargeable batteries, like ZINC/CARBON,
ZINC/CHLORIDE, ALKALINE etc, otherwise the batteries may explode suitable or leak.
Charging Rechargeable batteries
The charging current for this player is 120mA and has been optimised for over night
charging of Ni-MH batteries.
using earphones. Always switch the power off before
making any connections between the
player and another unit.
Note

4. EXTERNAL SPEAKER CONNECTION4. EXTERNAL SPEAKER CONNECTION
5. PLAYER MAINTENANCE5. PLAYER MAINTENANCE
66
For listening with speaker, you may connect a speaker box to this unit.
Connect the 3.5mm plug of the speaker box into the EARPHONE JACK of the unit.
Important: Impedance of the speaker box must be more than 8 ohm.
Otherwise, the amplifier of the unit may damage.
In the unlikelyevent of requiring spare parts, please contact our spare parts department on:
Tel: [phone]
Email: [email protected]

142mm(W) x 155mm(D) x 26mm(H)
Hold Switch
Set the HOLD switch(In bottom side) to
“ON” position, all the buttons will be
locked. Before operation, be sure to set
the switch to “OFF” position, for normal
operation.
7788

1. Slide OPEN knob to open the CD door.
2. Insert the CD with the printed side facing upwards and push the disc gently until locks
into place.
3. Press the CD door to close.
4. Press button to play.
When button is pressed at initial start up, the disc will begin to spin and after several
Seconds, then it will proceed to start playback automatically from track 1.
To review the total number of tracks on the disc, press button once.
During PLAY mode
The track number of the current selection is displayed.
the No. of track being played
During PAUSE mode
The elapsed time of the current track will flash.
The elapsed time of the current track will fash.
If no disc is inserted into the player and the button is pressed, the display will show “dISC ”.
:
:
:
dISC
1. EQ BUTTON
2. DIR.UP / ASP BUTTON
3. FR /SKIP DN BUTTON
4. FF /SKIP UP BUTTON
5. MODE / PROG. BUTTON
6. LCD DISPLAY
7. PLAY / PAUSE BUTTON
8. STOP / RECHARGE BUTTON
9. VOLUME-
10.VOLUME+
11.OPEN KNOB
12.PHONE JACK
13.DC JACK
14.BATTERY COMPARTMENT
15.HOLD SWITCH (BOTTOM)
991010
1 2 3 4 5
6
7 8 9 10 11 12 13
14 15

This unit can read audio CDs and MP3 CDs.
1. Place an MP3 disc with the printed side facing upwards, and push the CD centre
lightly to lock it in position.
2. Press to start playback.
• When playback starts, the “MP3 ” icon, current directory number and file number and its
elapsed playing time is shown in the display.
• To skip through the directories (albums) on the disc press the DIR.UP/ASP button
repeatedly.
11. MP3 - CDS PLAYBACK11. MP3 - CDS PLAYBACK
During playback, each time the MODE/PROG. button is pressed, the playback mode will
be changed as follows:
In CD mode: In MP3 mode:
NORMAL play -> NORMAL play ->
( 1 ) Repeat One -> ( 1 ) Repeat One ->
( ALL) Repeat All -> ( ) Repeat DIR ->
(Int) Intro Scan -> ( ALL) Repeat ALL->
(Rnd) RANDOM -> (Int) Intro Scan ->
NORMAL Play (Rnd) RANDOM ->
NORMAL Play
12. PLAYBACK MODES12. PLAYBACK MODES
13. REPEAT AND INTRO SCAN PLAY13. REPEAT AND INTRO SCAN PLAY
Repeat Play (Repeat One/Repeat All/Repeat Dir)
Repeat play (Repeat One/Repeat All/Repeat Dir)
1 To repeat the same track
Press MODE/PROG. button repeatedly
during playback until “ 1Repeat One” is shown in the
display. Select the desired track to be repeated by pressing
Or button.
2 To repeat the whole disc
Press MODE/PROG. button repeatedly during
Playback until “ ALL Repeat All ” is shown in the display.
3. To repeat directory (for MP3 mode only)
Pres MODE/PROG.button repeatedly during playback
until “ Repeat Dir ” is shown in the display.
• The current directory being listened to will be played
Repeatedly.
INTRO Play - Listen to First Ten seconds of each track
1. Press MODE/PROG.button repeatedly During playback until
Int is shown in the display, then press button to starting
INTRO play.
2. Each track is played for 10 seconds.
• INTRO play will start from the track that immediately follows
the current track.
To return to normal playback, repeatedly press the MODE /
PROG.button repeatedly until no lcon is shown in the
Display.
:
MP3
:
MP3
1
MP3
:
ALL
:
MP3
DIR
:
MP3
:
CD
INT
:
CD

14. RANDOM PLAYBACK14. RANDOM PLAYBACK
Enables all the tracks on a disc to be played in a Random sequence.
1. Random (for CD)
Press MODE/PROG. button repeatedly during playback
until “Rnd” is shown in the display.
After all tracks are played, the player will stop automatically.
2. Random (for MP3 only)
Press MODE/PROG. button repeatedly during playback
until “Rnd” is shown in the display. All tracks of the disc will
be played in a random order repeatedly.
After all files are played, the player will stop automatically.
NOTES:
• To skip to the next track: press button. However, you can not skip to a previous track.
This allows selected tracks on the disc to be played in a specified
order.
During CD playback
1. For audio CDs in stop mode, press MODE/PROG. button
And the “ ” icon appears in the display.(Press STOP/
RECHARGE button for cancel)
2. Press or button to select the desired track, then
press MODE/PROG.button to store the selected track in
memory and the “ 02 ” icon will appear to the right of the
Selected track.
3. Repeat step 2 to store other tracks.
4. Press button to start playback and the
“ ”Icon appears in the display.
5. To stop program playback, press button.
During MP3 playback
1. For audio MP3 in stop mode, press MODE/PROG. button
The “ ” icon appears in the display.
2. Press ASP/DIR. UP button to select the desired directory.
3. Press or button to select the desired file, then press
MODE/PROG. Button to store the selected file in memory
and the “00 000 P-02 ” icon will appear to the right of the
Selected file.
4. Repeat steps 2 to 3 to store other files.
5. Press button to start play and the “ ”
Icon appears in the display.
6. To stop program play, press button.
Notes:
• The program is also erased when the disc compartment is opened or the auto power off
Function turns the power off.
• To cancel program operation, press button once whilst in stop mode.
PGM
PGM
PGM
PGM
CD
:
CD PGM
CD PGM
CD PGM
MP3
MP3
PGM
MP3
PGM
15.PROGRAMMED TRACK PLAYBACK15.PROGRAMMED TRACK PLAYBACK
MP3
PGM
CD
RND
:
MP3
RND
:
MP3
PGM

The DIGITAL ANTI SKIP PROTECTION system incorporates a special electronic
circuit that prevents sound from skipping when the unit is subject to shocks and vibration
during playback.
When the unit receives a physical shock which prevents the laser pick-up from “READING”
the CD, this system immediately starts playing the sound stored in its memory and
continues
until the laser pick-up recovers.
If the unit is subject to continuous shocks and all the data stored in memory is used up the
sound will start to skip.
When playback is started, the SKIP PROTECTION system turns on automatically and the
protection function is activated.
• During CD disc playback, “ASP” is shown in the display.
16. DIGITAL ANTI SHOCK OPERATION16. DIGITAL ANTI SHOCK OPERATION
Your hearing is very important to you and to us, so please take care when operating this
equipment. It is strongly recommended that you follow the listed guidelines in order to
prevent possible damage or loss of hearing.
ESTABLISH A SAFE SOUND LEVEL
• Over time your hearing will adapt to continuous loud sounds and will give the impression
that the volume has in fact been reduced. What seems normal to you may in fact be
Harmful.
To guard against this BEFORE YOUR HEARING ADAPTS set the volume at a low level.
• Slowly increase the level until you can hear comfortably and clearly and without
distortion.
• Damage to your hearing is accumulative and is irreversible.
• Any ringing or discomfort in the ears indicates the volume is too loud.
Once you have established a comfortable listening level, DO NOT INCREASE THE
SOUND LEVEL FURTHER.
The following list of typical sound levels may assist you in recognizing just how loud you
have set the volume level.
DECIBEL
Level dB Example
30dB Quiet library, soft whisper
40 Living room, fridge freezer bedroom away from traffic
50 Normal conversation, quiet office, light traffic
60 Electric sewing machine
70 Vacuum cleaner, hair dryer, noisy restaurant.
THE FOLLOWING NOISE CAN BE HARMFUL UNDER CONSTANT EXPOSURE
80dB Average city traffic, alarm clock buzzer at 2 feet, food mixer.
90dB Motorcycle, heavy goods vehicle, petrol lawn mower.
100 Pneumatic drill, chain saw, garbage truck, disco / night-club.
120 Rock band concert, thunderclap.
PERMANENT LOSS OF HEARING
140 THRESHOLD OF PAIN Gunshot 2 feet away.
180 Rocket Launching pad.
Press the EQ button activates 4 kinds of sound effect as follows:
P(POP) J(JAZZ) R(ROCK) C(CLASSIC)
17. PRESET EQUALIZER FUNCTION