Goodmans GPS04BLK User manual

USER MANUAL
MODEL: GPS04BLK
CD BOOMBOX

Welcome1
Troubleshooting5
Technical Specifications6
Customer Support7
Your CD Boombox
2.1 In The Box
2.2 Front View
2.3 Top View
2
Quick Setup
3.1 Power On/Off and Function Selection
3.2 Standby & Auto Standby
3.3 Adjusting the Volume
3
Operation4
CD Operation
4.1 Load a Disc
4.2 Play a Disc
4.3 Skip Tracks And Search For A Specific
Point To Play
4.4 Programmed Play
4.5 Repeat Single/All Track(s)
Radio Operation
4.6 Tuning a Station
Aux-In Mode
4.7 Aux In Mode
2.4 Rear view
2.5 Control panel
3.4 Bass Enhancement
3.5 Fitting Batteries
3.6 Connecting Earphones
Bluetooth Operation
4.8 Pairing a Bluetooth Device
4.9 Operating a Connected Device

GPS04BLK
Welcome
Thank you for choosing this Goodmans product. We’ve been
making electronics for the British people for 70 years. Each of
our projects has been carefully designed to be great at what it
does and this one is no exception. We hope you enjoy your
new CD Boombox.
1
Your CD Boombox2
In The Box
Carefully remove your CD Boombox from the packaging.
Inside the box you will find:
• CD Boombox
• Mains Power Supply Lead
• Quick Start Guide
• Guarantee Booklet
If any of these items are missing, contact customer support.
Visit: www.goodmans.co.uk/support
2.1
Mains Power
Your CD Boombox requires a mains supply of 230-240V AC ~ 50Hz.
Please ensure that your mains supply is compatible before use.
Disconnect the Power Cord from the mains when not in use.
Position of CD Boombox
Place on a flat, stable surface that is not subject to vibrations. Avoid
the following locations:
• Where it is exposed to direct sunlight
• Where it is close to heat radiating sources
• Where the humidity is high and ventilation is poor
• Where it is dusty
Adjusting the Antenna
Fully extend the antenna to ensure good reception in both AM and FM
Radio modes. It may be necessary to alter the position of the CD
Boombox and/or the antenna to achieve the best signal.

GPS04BLK
Front View2.2
A SPEAKERS. Stereo speakers.
B BASS PORTS. Bass pressure
release ports.
C PHONES output. Connect
earphones to this socket.
D Carry handle.
E VOLUME control. Rotate to
increase or decrease the volume
output.
F FUNCTION switch. Enable RADIO /
CD /Bluetooth or AUX functions.
G BASS button. Press to enhance the
bass output.
H CD compartment. Press ‘OPEN’ to
release the CD compartment lid.
I STANDBY button. Press to wake or
enter STANDBY mode.
J RADIO BAND switch. Set the radio
band from AM, FM or FM STEREO.
K Telescopic antenna. Extend for the
best radio reception.
L RADIO TUNING control. Rotate to
scan up or down the selected band
frequencies.
M AUX INPUT socket. Connect
external audio sources with a 3.5mm
audio cable.
N AC mains input socket. Connect
the mains cable to this socket.
A B B A
AC IN ~
ANT.
N
C E FD HG I J LK M
Top View
Rear View
2.3
2.4

GPS04BLK
Control Panel2.5
O button. Press to skip to previous
CD tracks. Press and hold to fast
rewind CD tracks.
P PROG button. Press to enable
program function.
Q POWER LED. This will illuminate
when the power is on.
R button. Press to stop playback of a
CD.
S PAIR/ button. In CD mode press
to Play or Pause playback of a CD. In
Bluetooth mode press to initiate the
pair function.
T FM STEREO LED. Illuminates when
a station is tuned in the FM STEREO
mode.
U button. Press to skip to next CD
track(s). Press and hold to fast
forward CD tracks.
V REP button. Press repeatedly to
toggle the repeat functions.
W LCD DISPLAY. Displays all current
information releative to the mode
selected.
X BLUETOOTH LED. Indicates the
status of a bluetooth connection.
O P WX V U
RQ TS

GPS04BLK
Quick Setup3
Power On/Off and Function Selection
1. This CD Boombox is supplied with a mains cable.
To connect the power insert the figure 8 shaped end in the
rear of the unit (N).
2. Insert the UK plug into a household power socket, and
switch the power on.
3. Press the STANDBY button (I) to wake from Standby mode
4. Set the FUNCTION switch (F) to either RADIO /CD /Bluetooth
or AUX.
Standby & Auto Standby
1. Press the STANDBY button (I) to wake from Standby mode.
2. Press the STANDBY button (I) again to enter Standby mode.
Due to new ECO regulation requirements this product
incorporates a power saving feature.
3. When in CD, Bluetooth or AUX mode, once audio playback
has ceased and the unit has stood idle for approximately 15
minutes, it will switch into a ‘power-down’ power saving
mode.
4. To wake the unit up, press the STANDBY button (I).
3.1
3.2
AC IN ~

GPS04BLK
Adjusting the Volume
Rotate the volume control (E) clockwise or anti-clockwise to
increase or decrease the volume output.
Bass Enhancement
Press the BASS button (G) to increase the bass output. Press
again to reduce.
Fitting Batteries
1. Open the battery compartment on the bottom of the unit by
pressing down on the OPEN symbol and sliding in the
direction of the arrow (see diagram below).
2. Insert 8 x D size batteries taking care to match the + & -
polarity symbols correctly.
3. Replace the battery compartment cover.
The mains cable must be detached from the AC socket of the
player for the batteries to power the unit.
Leaking batteries may damage the battery cabinet and the
player as a whole. If you are not going to use the CD Boombox
for an extended period, please remove the batteries to avoid
damage.
Caution: Danger of explosion if battery is incorrectly inserted.
Replace only with the same or equivalent type.
3.3
3.4
3.5

GPS04BLK
Connecting Earphones
You will require a 3.5mm adapter if your earphones /
headphones do not have this size plug.
Connect the 3.5mm jack into the PHONES output socket (C)
on the left of the unit.
• Listen at moderate volumes to avoid hearing damage.
• If you hear no sound during playing, do not turn the volume
up as the music may suddenly begin at a high volume.
• Excessive sound pressure from earphones and
headphones can cause hearing loss.
• To avoid damaging your ears, adjust the volume to the
lowest safe level before playing, and turn up to the desired
level when playback has started.
3.6

GPS04BLK
CD Operation
Operation4
4.1
4.2
4.3
Load a Disc
1. Open the CD lid using the OPEN button (H).
2. Load a disc onto the disc tray with the label side facing up.
3. Close the CD door.
Play a Disc
1. Slide the FUNCTION (F) switch to the CD position.
2. Follow the steps above to load a disc (if not already loaded).
3. The player begins to read the disc immediately.
4. When the disc is successfully read, the total number of
tracks on the disc will appear on the LED display (D).
5. Press the PAIR/ button (S) once to begin playback.
Press the button again to pause the music playback. The
play symbol ‘ ’ flashes to indicate the player is in Pause
mode; press the button (R) to cease music playback. The
LED shows the total number of tracks again.
Skip Tracks And Search For a Specific Point
To Play
1. Press the button (U) once during playback to skip to the
next track. To skip to a specific track ahead, press this
button several times until you reach the track number
required.
2. Press the button (O) once during playback to return to
the beginning of the current track. Press this button twice
repeatedly to skip to the previous track. To skip back to a
specific track, press this button several times.
3. Hold the button (U) during playback to fast forward the
current track.
4. Hold the button (O) during playback to fast rewind the
current track.

GPS04BLK
Programmed Play
To program an alternative playback order of up to 20 tracks
follow the below steps.
1. Make sure the unit is not playing a disc.
2. Press the PROG. button (P) once. The program sequence
“00” flashes on the LCD display.
3. Select the first track to be programmed using / (U,
O) buttons.
4. Press the PROG. button (P) again to store and advance to
the next programmed track. The program sequence
indication changes to “02” momentarily waiting for your next
input.
5. Repeat the steps above to program more tracks. A
maximum of 20 tracks can be programmed.
6. Press the button (B) to begin the programmed playback
in the preferred order. The PROG indicator appears in the
top left of the LCD display.
7. You can press the button (F) twice to terminate the
programmed playback or switch to a different input mode.
Repeat Single/All Track(S)
1. During playback press the REP. button (V), you will see the
repeat once icon ‘ ’ on the left of the LCD display. This
indicates the current track will repeat until the button (R) is
pressed.
2. During playback press the REP. button (V) twice, you will
see the repeat all icon ‘ & ALL’ on the left of the LCD
display. This indicates that all the tracks of the current disc
will repeat until the button (R) is pressed.
3. To turn off the REPEAT function press the REP. button (V)
until the repeat icons disapear or press the button (R).
4.4
4.5
PROG
PROG
1
ALL