Gorenje Simplicity DT6SY2W User manual

1
2
3
min 650 mm
A
FB
C
F
E
H
90°
335
205
600 / 900
G

o 150
4
a
b
5
K
C
B
M
EN 4
BASIC TECHNICAL DATA
Type
DT6SY2W
DT6SY2B
Quantity of motors
1
Max. motor capacity
200W
Lighting - halogen
2 x 20W
Total power consumption of
cooker hood
240W
Electric voltage
230V AC
Protection class against
electric shock
I.
Dimensions (mm):
w x d x h (Fig. 8)
600 x 420 x 352
Noise level
65dBA
Color –version
Inox –glass
Grease filter
2 pc –metal
Control
SWITCH
Number of capacity levels
3
Exhaustion
Exhaustion with reduction
150mm
120mm
Exhaustion
- UPPER
-RECIRCULATION
ACCESSORIES OF COOKER HOOD
Dowels and screws fro mounting of cooker hood on
a wall and screws for fastening of decoration
chimney
Screws 5 x 50mm (4 pieces)
Screw 3,9 x 8mm (2pc)
Dowels H 8 (4 pieces)
Upper cover of decoration chimney for recirculation
Console for fastening of decoration chimney
Decoration chimney (2 pieces)
Backflow valve –is integral part of ventilator motor
Reduction 150 / 120mm
*The declared noise emission level of this appliance
is 62 dB(A), what represents the A level of acoustic
power in comparison to reference acoustic power
1pW.
ACCESSORIES OF COOKER HOOD FOR
ORDERING
Carbon filter –set - SAP 428642
Exhaustion hose
120 or150 mm + fastening clip
Recirculation set - SAP 431926
435005en
BASIC TECHNICAL DATA
Type
DT9SY2W
DT9SY2B
Quantity of motors
1
Max. motor capacity
200W
Lighting - halogen
2 x 20W
Total power consumption of
cooker hood
240W
Electric voltage
230V AC
Protection class against
electric shock
I.
Dimensions (mm):
w x d x h (Fig. 8)
900 x 420 x 352
Noise level
65dBA
Color –version
Inox –glass
Grease filter
3 pc –metal
Control
SWITCH
Number of capacity levels
3
Exhaustion
Exhaustion with reduction
150mm
120mm
Exhaustion
- UPPER
-RECIRCULATION

EN 3
NOTICE!
The caught fat in the filter has influence not only to
the effectiveness of cooker hood but at neglected
maintenance could cause also a fire! Therefore we
recommend the observation of instructions for
cleaning and changing of filters.
LIQUIDATION OF CARBON FILTERS
AFTER FINISHED LIFETIME
The used filters can be put to normal household
waste.
The liquidation should be provided in
concordance with the corresponding national
standards and regulations.
LIGHTING
The cooker hood has halogen bulbs 2 x 20 W
(type 12V/20W - G4).
REPLACING OF HALOGEN BULB (FIG. 7)
Disconnect the cooker hood from the power net.
Shift a flat piece (a small screwdriver or flat knife)
carefully between the rings of halogen lighting.
With slight lever action make free the internal ring
with the glass cover of lighting.
Provide the replacement of halogen bulb.
Return back the ring with the glass cover of
lighting to original location.
CAUTION!
Do not touch the halogen bulbs with your naked
fingers
CLEANING
Clean regularly the internal and external parts of
cooker hood with soft cleaning agents.
Never use abrasive cleaning means.
Clean the glass surfaces with special means for
glass, mirrors and windows.
METHOD OF USE AND LIQUIDATION OF
PACKAGING
Grooved cardboard, packaging paper
- sale to waste collecting company
- to collecting vessels for used paper
- other reuse
Polystyrene
- to corresponding collecting vessels
Packaging foil and PE backs
- to collecting vessels for plastic
LIQUIDATION OF APPLIANCE AFTER
FINISHING OF USE
This appliance is marked in accordance with
Directive 2002/96/EC on manipulation with waste
from electric and electronic equipment –WEEE.
This directive determines the unified European (EU)
frame for collection and recycling of used
equipment.
The appliance contains valuable materials which
should be reused after finishing of their use. Please
give your used appliance to waste processing
company.
CLAIMS
If there is any defect on the appliance within the
guarantee period, do not repair it self. Apply a claim
in the shop in which you bought the appliance or at
service representatives, mentioned in the Guarantee
conditions.
At applying of claim observe the text of Guarantee
sheet and Guarantee conditions.
REMARK:
The producer reserves the right for providing of
minor changes, resulting from innovations or from
technologic modifications of the product.
67
L
1L
2L
3L
3
2
1
0
250
95
349
420
600 / 900
270
min 485
max 955
150
8

EN 1
OPERATION AND MAINTENANCE
MANUAL
Dear customer,
You have purchased a product of our new series of
cooker hoods. We hope that our product will serve
you well and for long time. We recommend you to
study these instructions and to operate this product
according to them.
IMPORTANT INFORMATION AND
RECOMMENDATIONS
The cooker hood should not be connected to
smoke flue, which is used for combustion exhaust
The appliance can be used in exhaust mode (the
exhaustion of exhalations into waste air stack) or,
after additional buying of carbon filter and
recirculation set in recirculation mode (circulation
through carbon filter).
If there is in operation simultaneously with the
cooker hood (in exhaustion mode) appliance of
type B in the same room - heat source (for
instance with gas, oil, diesel fuel or with solid
fuel), which draw combustion air directly from the
room, then it should be taken into account, that
these appliances create at combustion a certain
level of under-pressure. Therefore it is necessary
to provide a sufficient inflow of air (from the
outside environment).
Do not handle with open flame under the cooker
hood (for instance at flambéing etc.)!
The big fat deposits from roasting on the grease
filter should be regularly removed.
Follow the below determined instructions at
replacing of filters.
This appliance should be operated with adults
only.
This appliance is designed for normal household
use.
This appliance is not designed for use with
persons (including children), their physical,
sensual or mental disability or lack of experience
and knowledge hinders the safe use of appliance,
except when they are under supervision or they
were introduced concerning use of appliance with
the person responsible for their safety. The
children should be supervised for ensure, that
they would not play with the appliance.
The accessible parts could be hot at using of
cooking devices.
The cooker hood is an electric appliance with Y –
type connection. If the power cord is damaged, it
should be replaced with the producer, his/her
service technician or with similarly qualified
person, for to prevent the creation of dangerous
situation.
The producer is not responsible for damages
caused with faulty installation or faulty using of
appliance.
ATTENTION
Plug in cooker hood to the net before fixing on the
wall and check function of motor (all speeds) and
function of lights.
Check whether motor is not too noisy, whether
have regular running.
Do not remove protection foil from cooker hood
and decoration chimney.
Check if carton box is not demaged, check
sufrace of cooker hood if there are not scratches
or dishing.
IN CASE OF FAILS DO NOT FIX COOKER
HOOD ON THE WALL AND CLAIMED IT AT
YOUR SALER!!!
Fix the cooker hood on the wall with protection
foil. After fixing and setting right height
of decoration chimney remove protection foil.
Do not move with decoration chimney without
protection foil. In other case there will be
scratches on surface.
Following these instructions you avoid useless
claiming.
DESCRIPTION (FIG.1)
A –Cooker hood
B –Lower part of decoration chimney
C –Upper part of decoration chimney
E –Carbon filter (for recirculation only)
F –Grease filter –metal cassette
M - Cover of decorative chimney
H - Switch
ELECTRIC CONNECTION
Check before installation of appliance that the
voltage in your power net corresponds to data
given on the production sheet inside of the
appliance.
The appliance is provided with a power cord is
ended with a plug –class I. of protection against
electric shock.
Connect the appliance to a socket corresponding
to valid national standards.
INSTALLATION
The distance between the cooker hood and the
hotplate should not be less as 650mm (fig.2).
ATTENTION
The attached dowels and screws are designed for
fastening of cooker hood on a wall from concrete
or full bricks. For other wall material a
corresponding type and size of dowels and
screws should be used.
Leave the fastening of cooker hood to a
specialist!
EN 2
MOUNTING OF COOKER HOOD
Unpack the appliance from packaging.
Drill holes for fasteners according the drawing 3.
Tap the fasteners to drilled holes.
Fix the appliance with provided screws throu
holes “G”
IMPORTANT:
The horizontal location of cooker hood should
be observed.
THE EXHAUSTION VERSION
At use of exhaustion version (see fig. 4) the
exhalations are led into the exhaustion opening
with the exhaustion hose, which is connected to
the cooker hood with a flange. The exhaustion
hose and the fastening clips should be bought
additionally.
The exhaustion is provided through the upper
outlet of the cooker hood, on which the
exhaustion hose should be connected and the
other end of hose should be connected into the
exhaustion opening. The diameter of exhaustion
hose should be the same as the diameter of
connecting flange –e.g. Ø150mm, or Ø 120mm
with a reduction piece (if you use connection hose
Ø 120mm, you will decrease exhaust capacity
and increase noise level)
MOUNTING OF EXHAUSTION VERSION
AND OF DECORATION CHIMNEY
Fasten with help of a hose clip on the hinged on
cooker hood the one end of exhaustion hose,
fasten the other end into the exhaustion opening.
Both parts (the upper C and lower B) of
decoration chimney, shifted one to the other,
place on the hinged on cooker hood.
Shift the upper part C into the required height,
mark the upper location and mark the fastening
openings of console (K).
Remove the decoration chimney and bore the
marked openings for the dowels.
Screw on the console (K) together with cover of
decoration chimney (M).
Fasten once more the both parts of decoration
chimney, shift out its upper part and fasten to the
console with two screws.
IMPORTANT:
Remove protection foil from decoration chimney
not untill last assembly of decoration chimney!
IMPORTANT!
The carbon filter should not be installed in the
cooker hood at exhaustion version.
RECIRCULATION VERSION
A carbon filter and recirculation set should be
bought for the cooker hood in recirculation
version (fig. 9). The exhalations are exhausted
through the carbon filter.(fig. 1 (E)) The circulation
air with removed smell is led with exhausted hose
through air spreader to the ventilation openings in
upper part of decorative chimney to the room.
This version is used in cases, when there is no
waste air stack at disposal.
CAUTION!
The carbon filter should be installed in the
cooker hood at recirculation.
SETTING THE POWER LEVEL
Power level 1, 2, 3 is set by turning the control
knob.
If the control knob is set on 1L, 2L, 3L ventilation
and light is powered together.
TURNING ON THE LIGHTS
Light is ON when the control knob is in position “L”
TURNING OFF THE HOOD
The hood is OFF when the control knob is in position
“0”.
MAINTENANCE AND CLEANING
At cleaning or maintenance switch the appliance
off from the power and this with disconnecting
from the socket or with switching off of
corresponding circuit breaker.
The regular maintenance and cleaning ensure the
efficiency, reliability and longer lifetime of cooker
hood.
Pay special attention to grease filter and to
carbon filter.
For cleaning of cooker hood do not use cleaning
articles containing aggressive substances mainly
chlorine and dissolvents.
GREASE METAL FILTER
The grease metal filter (F) catches the fat
particles.
The metal filter should be cleaned manually or in
dishwasher (at 65C) with use of appropriate
detergents.
The filter can slightly change its color when
washed in dishwasher; nevertheless this fact has
no influence to its functionality.
Let the filter thoroughly dry after washing and
return it to cooker hood in dry state only.
CASSETTE CARBON FILTER
The carbon filter (E) absorbs the kitchen smell.
The carbon filter should be never washed!
INSTALLATION OF CASSETTE CARBON
FILTER
Disconnect the appliance from the power net.
Take out the grease filter (F) and fasten the
cassette carbon filter (E) to its internal side –see
the picture.