Graco 3250281 - Lauren Drop Side Convertible Crib User manual

ASSEMBLY INSTRUCTIONS
PRINTED IN CHINA
HARDWARE AND TOOLS DIAGRAM
1
LaJobi Industries. - 257 Prospect Plains Rd. Cranbury,NJ 08512-Phone: [phone]
Bulletin No. A-RTAUPS01-00
Convertible Crib
Adult assembly required. Small parts may present prior to assembly.
PARTS LIST
REF. PART NAME QUANTITY
A. Crib Ends(Top) 2
B. Crib Ends(Bottom) 2
C. Front Leg 2
D. Dropside Rail 1
E. Back Rail Top 1
F. Back Rail Middle 1
G. Back Rail Bottom 1
H. Back Rail Leg 2
I. Wooden connecting block 3
J. Bottom Stretcher 1
K. Metal Spring support platform 1
L. 3 1/4 " Bolt 14
M. 2 1/4" Bolt 2
N. 1 1/2" Bolt 4
O. 3/4" Bolt 4
P. Barrel Nuts 16
Q. Allen Wrench 1
R. Wood Dowels 30
S. Casters 4
T. Block brake 2
U. Wood Screws 3/4″ 12
M
L
Enclosed please find simple step-by-step instructions to help you quickly assemble your product. Before you begin we
recommend that you follow the steps below:
1. Please read the instructions thoroughly
2. Identify all parts and hardware.
3. You will need the following tools:
Philips Head screw driver
Flat head screw driver
Hammer.
To protect your parts during assembly please place them on a soft surface. To clean surface use only water on a damp cloth.
Do not use window cleaners or cleaning abrasives as it will scratch the surface and could damage the protective coating.
3 1/4" Bolt
Barrel Nuts Allen Wrench
Casters
Block brake
Wood Dowel
2 1/4" Bolt
3/4" Bolt
NO
Model shown is example only.
Styles may vary.
Wood Screw 3/4″
T
P Q
RS
1 1/2" Bolt
U

BULLETIN NO. FCI00-00 2
Furniture Care Instructions
Room Climate Control
Wood, when first cut contains more than 50 percent water. When it is prepared for furniture
construction it is placed in a Kiln and the moisture content is brought down to 8 to 10 percent. Wood
is porous and responds to its environment. If the room has high humidity it will absorb it and expand
and if the humidity is low it will lose moisture and shrink.
It is important that the humidity levels in the room be controlled from extremes of too much
humidity or too little. Furniture should not be placed close to air-conditioning outlets, fire places,
radiators, space heaters, humidifiers or dehumidifiers. Exposure to extreme variations of
temperature and humidity can damage any fine wood product.
The Ideal Environment for Fine Furniture
Fine wood furniture will have fewer problems when its environment is controlled at a temperature
between 65 and 75 degrees and a relative humidity between 35 and 40 percent. Wood placed in an
environment out side of those limits can and will shrink or expand and may develop some small
cracks which are not material or structural defects.
Sticking Doors and Drawers
With the minor changes in temperature and humidity doors and drawers may swell and be
difficult to open or close. Tolerances have been built into the units but extreme conditions may still
cause sticking. This will adjust back to normal over time but until it does consider using a
dehumidifier or rub candle wax or paraffin on the sides that stick.
Avoid Direct Sunlight
Keep the furniture out of direct sunlight. Ultraviolet rays will fade colors and in some cases
darken them. It can also cause crazing or hair line cracks in the finish. White finishes will yellow
naturally over time and exposure to direct sunlight will hasten this natural process along with some
woods darkening naturally over time; this is not considered to be a quality defect.
Proper Storage
If you need to put your furniture in storage for any period of time do not store them in a damp
basement or hot dry attic. Allow air movement around the furniture and do not stack anything on it.
In General
Protect furniture surface from hot or extremely cold items.
Use coasters under hot or cold beverages
Do not use synthetic fabric under accessories or lamps
Protect tops from pens, makers and crayons
Oils from potpourri and other scented items can damage the furniture finish.
Do not drag items across the surface of the furniture.
Allow the surface to breath by rotating your accessories and lamps.
Do not over polish the furniture, do it only two or three times a year. Over polishing can
distort the natural finish of the product.
Do not wax the furniture as wax build up can destroy the natural finish of the product.
When moving furniture always lift the unit. Do not push or drag it to avoid damage to legs
Keep the furniture level so doors and drawers open and close freely.
Clean with a damp, not wet, cloth. Use only a mild soap. Do not use abrasive cleaners.

BULLETIN NO. PAP00-00 3
STOP
IF YOU EXPERIENCE ANY
ISSUES WITH THIS PRODUCT
BEFORE YOU
RETURN THIS TO
THE RETAILER
PLEASE FOLLOW
PROCEDURES ON THE
REVERSE SIDE OF THIS FORM.

BULLETIN NO. PAP01-00 4
Product Assistance Procedures
You have purchased a quality piece of furniture. Our international team has
spent many hours designing and engineering this piece and packaging to ensure you
will be satisfied with your purchase. But if for any reason you need help with your
purchase please contact us at any time.
Procedures to follow should you have any questions:
For best and most timely service please contact us by e-mail at [email protected]
Please provide the following information in your e-mail.
1. Your Name__________________________________________________
2. Address_____________________________________________________
_____________________________________________________
3. Phone number________________________________________________
4. Place and date of purchase_____________________________________
_________________________________________________________
5. Item number and description of your product. ____________________
_________________________________________________________
_________________________________________________________
The item number can be found on the back of the case or on the foot/headboard
of the crib. Please include all numbers found on that label including the PO# and
production date.
6. Short description of the issues and attach a photo if possible.
____________________________________________________________
____________________________________________________________
____________________________________________________________
Someone will contact you via e-mail or phone to help you with your issues.
If you do not have internet access, please fax the above information to
609-409-5809
If you do not have internet or fax access, please call us at 888-266-2848 and be sure
to have all the above information ready to give to your Client Service Specialist.

WARNING!
• FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR DEATH.
• READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS FOR
FUTURE USE.
•UPON COMPLETION OF ASSEMBLY BE SURE ALL SCREWS, BOLTS AND FASTENING
DEVICES HAVE BEEN SECURELY TIGHTENED. A FREQUENT CHECK SHOULD BE MADE.
• BEFORE
•
EACH USAGE OR ASSEMBLY, INSPECT CRIB FOR DAMAGED HARDWARE,
LOOSE JOINTS, MISSING OR BROKEN PARTS AND SHARP EDGES. DO NOT USE THIS
CRIB IF ANY PARTS ARE MISSING OR BROKEN. ASK YOUR DEALER OR WRITE TO
LAJOBI INDUSTRIES, INC, 257 PROSPECT PLAINS ROAD, CRANBURY, NJ 08512. FOR
REPLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED. DO NOT
SUBSTITUTE PARTS OF ANY KIND.
AFTER RAISING SIDE, MAKE SURE LATCHES ARE SECURE.
• WHEN THE CHILD IS ABLE TO CLIMB OUT OR REACHES THE HEIGHT OF 35 INCHES
(90 CENTIMETERS), THE CRIB SHALL NO LONGER BE USED. THE CHILD SHOULD
BE PLACED IN A YOUTH BED OR TODDLER BED.
• DO NOT
• DO NOT LEAVE CHILD IN CRIB WHEN SIDE IS LOWERED. BE SURE SIDE IS IN RAISED
AND LOCKED POSITION WHENEVER CHILD IS IN CRIB.
PLACE CRIB NEAR WINDOW WHERE CORDS FROM BLINDS OR DRAPES
MAY STRANGLE A CHILD.
• IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN’S PRODUCTS.
• WHEN CHILD IS ABLE TO PULL TO STANDING POSITION, SET MATTRESS TO LOWEST
POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS THAT
COULD SERVE AS STEPS FOR CLIMBING OUT.
• NEVER USE PLASTIC SHIPPING BAGS OR ANY PLASTIC FILM AS MATTRESS COVERS,
BECAUSE THEY CAN CAUSE SUFFOCATION.
• ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES (69 CENTIMETERS)
BY 51-5/8 INCHES (131 CENTIMETERS), WITH A THICKNESS NOT EXCEEDING 6 INCHES
(15 CENTIMETERS), THE DIMENSIONS OF THE MATTRESS SHALL BE TAKEN FROM
SEAM TO SEAM OR EDGE TO EDGE WHERE APPROPRIATE.
• DO NOT USE A WATER MATTRESS WITH THIS CRIB.
• WARNING. STRINGS CAUSE STRANGULATION! DO NOT PLACE ITEMS WITH A STRING
AROUND A CHILD’S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. DO NOT
SUSPEND STRINGS OVER A CRIB OR ATTACH STRINGS TO TOYS.
• WHEN STORING CRIB USE CAUTION AS EXTREME CHANGES IN TEMPERATURE OR HUMIDITY
CAN COMPROMISE THE CRIB MAKING IT EXTREMELY DANGEROUS TO YOUR CHILD.
• USE CAUTION WHEN A VAPORIZER OR HUMIDIFIER IS IN USE. ALWAYS AIM VAPOR AWAY
FROM THE CRIB AS WELL AS ANY OTHER WOODEN FURNITURE. PROLONGED PERIODS
OF HUMIDITY IN STORAGE AS WELL AS THE HOME CAN COMPROMISE THE CRIB.
• AVOID USING VAPORIZERS AND HUMIDIFIERS FOR PROLONGED PERIODS OF TIME.
5
!
BULLETIN NO. A-RTAUPS01-00
ASSEMBLY INSTRUCTIONS(continued)
LaJobi Industries. - 257 Prospect Plains Rd. Cranbury,NJ 08512-Phone: [phone]

ASSEMBLY INSTRUCTIONS(continued)
PRINTED IN CHINA
Step 1
Attach the back rail legs(H) to the
Back Rail Bottom (G) using wood
dowels(R) & 3 1/4” Bolts(L) & Barrel
Nuts(P). See Figure 1.
Step 2
Attach the Back Rail Middle(F) to the
back rail using wood dowels (R), then
insert 3 1/4” bolts(L) ,through the
back rail legs into the threaded insets
onto the back rail middle as shown in
Figure 2.
6
Figure 1
Crib Assembly
Figure 2
LaJobi Industries. - 257 Prospect Plains Rd. Cranbury,NJ 08512-Phone: [phone]
Model shown is example only.
Styles may vary.
Model shown is example only.
Styles may vary.
Bulletin No. A-RTAUPS01-00
H
H
G
L
L
P
P
P
P
L
L
Q
R
R
F
R
L
L
Q
P

ASSEMBLY INSTRUCTIONS(continued)
PRINTED IN CHINA
Step 4
Use the wooden connecting blocks(I)
and wood screws(U) to tightly affix the
Back Rail Top to the back rail as shown
in the figure 4 & 4A.
7
Figure 3
Figure 4
Figure 4A
LaJobi Industries. - 257 Prospect Plains Rd. Cranbury,NJ 08512-Phone: [phone]
Model shown is example only.
Styles may vary.
Model shown is example only.
Styles may vary.
Bulletin No. A-RTAUPS01-00
R
G
F
E
Step 3
Attach the Back Rail Top(E) to the
back rail using wood dowels (R),see
Figure 3.
F
E
G
E
F
U
U
I
I
I

ASSEMBLY INSTRUCTIONS(continued)
PRINTED IN CHINA
Step 6
Attach the Crib End Top(A) to the Crib
end using wood dowels (R), then
insert bolts(N), through the top rail of
crib ends bottom into the threaded
insets onto the crib end top as shown
in Figure 6.Repeat on the other end.
8
Figure 5
Figure 6
LaJobi Industries. - 257 Prospect Plains Rd. Cranbury,NJ 08512-Phone: [phone]
Model shown is example only.
Styles may vary.
Model shown is example only.
Styles may vary.
Bulletin No. A-RTAUPS01-00
Step 5
Attach the Front leg(C) to the crib
end bottom(B) rail using wood
dowels (R) and Bolts(L) & Barrel
nuts(P),see Figure 5. Repeat on the
other end.
L
Q
R
B
C
L
P
A
R
N
Q

ASSEMBLY INSTRUCTIONS(continued)
PRINTED IN CHINA
9
Figure 7
Figure 7A
Figure 8
Figure 8A
N
Step 7
Attach crib ends to the Back Rail using
wood dowels(R) & bolts(L) & barrel
nuts(P). See Figure 7. Then attach the
bottom stretcher(J) to the crib ends
using wood dowels (R) & bolts (N) &
barrel nuts(P) as shown in the Figure
7A.
Step 8
Locate the metal spring (K) with tabs.
Be sure the smooth side of metal
spring is paced upward.Position the
tabs of metal spring to mount to the
selected position onto the legs. Insert
the 3/4” bolts(O), through the tabs and
into thread insets onto the legs,then
tighten securely with Allen wrench(Q)
See the Figure 8A.
LaJobi Industries. - 257 Prospect Plains Rd. Cranbury,NJ 08512-Phone: [phone]
Model shown is example only.
Styles may vary.
Model shown is example only.
Styles may vary.
Bulletin No. A-RTAUPS01-00
J
P
P
R
R
R
L
L
Q
N
Q
N
P
Q
R
J
P
B
Q
O
K
K

ASSEMBLY INSTRUCTIONS(continued)
PRINTED IN CHINA
10
Figure 9
Figure 9B
T
T
Figure 9A
Step 9
Attach the Dropside Rail (D) to cribs ends as
shown in Figure 9A, pull the drop rail up to the
highest position. Screw the (2) block brakes (T)
into the holes provided in the lower plastic drop
track as shown in Figure 9B, tighten block
brakes with a Philips screwdriver.
Insert the foot casters (S) as shown in Figure
9C and tighten all bolts.Inspect the crib to make
sure it is assembled correctly and all bolts are
tight.
LaJobi Industries. - 257 Prospect Plains Rd. Cranbury,NJ 08512-Phone: [phone]
Figure 9C
S
Bulletin No. A-RTAUPS01-00
Model shown is example only.
Styles may vary.
D
S
S
C
D