Grotime Changeover User manual

This product is covered by a number of registered designs, trademarks and patents pending
Two adults required to assemble this cot.
!
The manufacturer's assembly instructions must be followed
in detail to ensure the safety features to the cot are not compromised.
!
6 in 1 cot to full size single bed

x2
AllenKey
HG
x10
FeetPads
HF
x12 x8
16mmBolts
HB
70mm Bolts
HA
x4
GuidePins
HC
x4
WoodScrews
HD
HARDWAREINVENTORY
PRE-INSTALLEDHARDWARE
PARTSLIST
2
GrotimeBadges Locking Bolts Drawer Handles
2 x End Panels
PB
1x Fixed Side
PA
1 x Drop Side
PC
1xSpacer End
PD
2xDrawers
PH
11 xSingle BedSlats
PG
11xCot BedSlats
PF
x8
20mm Bolts
HE
4 x BILATERAIL Base Rails
PE
2x BILATERAIL
Bed Brackets
PG
TM TM
35mmBolt
HH
x1

STEP2
ASSEMBLETHEBASE USING THE COT BED SLATS
Lay one side rail down then slot all slats into the mortises.
Place the second side rail on top.
Working from one end slot all stats into the mortises.
Use the four wood screwsto
r.
x2 x11
Assembled base rails
PE
Cot Bed Slats
PF
x4
WoodScrews
HD
ScrewDriver
1.
2.
3.
3
Ensure the slat with thewarning labels is correctly positioned
in the middle and the “this way down” lable
is facing down as directed by the
warning lable on the rails.
!
x4 x2
BILATERAIL
TM BaseRails BILATERAIL
TM Base Brackets
PGPE
ASSEMBLEBILATERAIL TM BED RAILS x8
20mm Bolts
HE
Patent pending
STEP1

x8
70mm Bolts
HA
End Panels
PB
x2
STEP 3
ASSEMBLE THE TWO OUTERENDSTO THEBASE
ASSEMBLE THE FIXED SIDE BETWEEN
ONEEND AND THE SPACER END
STEP 4
Do not tighten bolts at this stage
!
Do not tighten bolts at this stage
!
Assembled base with cot slats
x4
70mm Bolts
HA
Spacer End
APDP
x1 x1
FixedSide
4

STEP 5
SCREW FOUR GUIDE PINS INTO
ONEEND AND THE SPACER END
x4
Guide Pins
HC
Screw Driver
ASSEMBLE DROP SIDE
STEP 6
Ensure correct side is facing out.
!
x1
Drop Side
PC
5

STEP 7
FULLY SCREW IN LOCKING BOLTS
Lift drop side up until it clicks
into the locking position.
b.
a.
STEP 8
TIGHTEN ALL BOLTS
6

To lower drop side, lift from centre of toprail, hold side in that position while using your leg to push inwardon
centre of bottom rail. Then allow to slide gently down.
1.
2.
3.
OPERATION
STEP10
PLACE TWO BEDSIDE DRAWERS
BACK TOBACKON THE END OF THE COT
STEP9
Ensure drawer handles are facing out.
!
x2
Drawers
PH
7
x1
35mm Bolt
HH
Connecting bolt to hold
drawers together.
Slide drawersout to bolt the 2 units
together through hole provided
!

Remove dropside by reversing to step 5.
DAY BED CONVERSION
Remove dropside guide pins (HC) from the ends to prevent injury.
!
Day Bed with Drawers
8

FULLSIZESINGLEBED CONVERSION
STEP1 Disassemble the cot following the
assemble instructions in reverse ord
er.
Roll over cot ends on theirsides
b.
a.
STEP2
REPOSITION FOUR GROTIME BADGES TO EXPOSE THE SINGLE BED BASE HOLES AND
COVER THE COT BASE HOLES
9
Grotime Badges
Rollover action Patent Pending

1.
2.
3.
STEP 3
ASSEMBLE SINGLE BED BASE
Lay one side rail down then slot all slats into the mortises.
Place the second side rail on top.
Working from one end slot all stats into the mortises.
STEP 4
Use the four wood screws to
x the rails and slats together.
x2 x11
Bed Base Rails (assembled)
PE
Single Bed Slats
PG
x4
Wood Screws
HD
Screw Driver
10