Fisher-Price H4790 User manual

1
Instructions
Model Number: H4790
Please read these instructions before assembly and use of this product.
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Product features and decorations may vary from photo above.
www.fisher-price.com
WARNING
IMPORTANT! KEEP FOR FUTURE REFERENCE.

WARNING
This product contains small parts in its unassembled state.
Adult assembly is required.
Prevent serious injury or death from falls or sliding out:
• The child should at all times wear a safety harness correctly fitted and adjusted.
The tray is not designed to hold the child in the chair.
• Always keep child in view while in the high chair.
• Never leave child unattended.
• It is recommended that the high chair be used in the upright position only by
children capable of sitting upright unassisted.
2
2
CAUTION
Warning and Caution

3
3
Parts
Pad
3 Food Trays
2 Toys (Toys may be different)
Seat Back
Seat Bottom
Frame
Hinge Rod
2 Seat Bottom Tubes
4 Screw Retainers
Base Tray
Frame
Footrest
Headrest
Basket Storage Caddy
Front Base
Back Base
#10 x 2.2 cm
Black Screw
#10 x 2.2 cm
Black Screw
#10 x 2.2 cm Black Screw - 7
Shown Actual Size
#8 x 1.9 cm Screw - 8
Tighten and loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
#8 x 1.9 cm Screws
#8 x 1.9 cm Screws
#10 x 2.2 cm
Black Screw

4
2
• Slide a seat bottom tube through each set of plastic rings on
the seat bottom.
1
• Place the seat bottom face down on a flat surface.
• At an angle, fit the footrest on the seat bottom, as shown.
Assembly
Plastic Rings
Footrest
Seat Bottom
IMPORTANT! Before each use, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use
if any parts are missing or broken. Contact Mattel for replace-
ment parts and instructions if needed. Never substitute parts.
Seat Bottom Tubes
Plastic Rings
3
Seat Bottom Tubes
Plastic Rings
Plastic Rings
#8 x 1.9 cm Screw - 4
• Align the holes in the plastic rings and the seat bottom tubes.
• Insert a #8 x 1.9 cm screw through each plastic ring and into
the seat bottom tubes, as shown. Tighten the screws.
• Push the seat bottom tubes back and forth to be sure they are
secured to the seat bottom. If the seat bottom tubes move, you
have probably not fastened them properly. Remove the screws
and check to be sure the screw holes in the seat bottom tubes
and seat bottom plastic rings are aligned. Replace and tighten
the screws.

5
5
Assembly
4
Insert Screws Here
Footrest
• Insert two #10 x 2.2 cm black screws through the footrest and
into the seat bottom. Tighten the screws.
#10 x 2.2 cm Black Screw - 2
5
• Turn the seat bottom assembly upright.
• Fit the seat back pins into the openings in the top side of the
seat bottom assembly.
Seat Back Pin
Opening
Seat Bottom Assembly
Opening
Seat Back Pin
6
Hinge Rod
Hinge
• Turn the seat assembly face down.
• Insert the hinge rod through the hinge on the seat back and
seat bottom, as shown.
• Insert a #10 x 2.2 cm black screw into the hinge rod. Tighten
the screw.
• Set the seat assembly aside for Assembly step 9.
#10 x 2.2 cm Black Screw
7
• Pull the frame leg out on each frame to open. Make sure it
"clicks" into place.
Frame Leg

6
6
6
Assembly
8
• Identify the back and front base. The front base has tapered leg
tubes. You will use the back base for the next assembly step.
Tapered Leg Tube
Back Base
Front Base
9
Screw Retainer - 2
#10 x 2.2 cm Black Screw - 2
• Position a frame so that the decorated side is outward.
• Insert the back leg of a frame into the back base.
• Fit a screw retainer over the hole in the back base, as shown.
• Insert a #10 x 2.2 cm black screw through the screw retainer
and back base. Insert the back leg of a frame into the back
base. Tighten the screw.
• Repeat this procedure to attach the other frame back leg
to the other side of the back base.
Hint: The #10 x 2.2 cm black screws may have been assembled to the
screw retainers.
Frame Back Legs
Frame Decorated Side
Back Base Hole
Screw Retainers
Back Base Hole
10
• While pressing the levers on the seat height adjusters, lift them
to position 4 on the frame front legs, as shown.
Seat Height Adjusters
Position 4
Press Lever
11
• Fit the seat assembly between the two frames.
• Insert the seat bottom tubes into the sockets in each seat
height adjuster.
Hints:
•Be sure the seat height adjusters are in the same position (position 4).
•You may need to push the frames apart slightly to fit the seat bottom
tubes into the seat height adjuster sockets.
Seat Bottom Tubes
Sockets
Seat Assembly

7
7
7
Assembly
12
Front
Leg Holes
Screw Retainer - 2
#10 x 2.2 cm Black Screw - 2
• Insert the frame front legs onto the front base.
• Fit a screw retainer over a hole in the front leg.
• Insert a #10 x 7/8" (2.2 cm) black screw through the screw
retainer and front leg. Tighten the screw.
• Repeat this procedure to secure the other end of the front
base with the remaining screw retainer and #10 x 2.2 cm
black screw.
Hint: The #10 x 2.2 cm black screws may have been assembled to the
screw retainers.
Screw Retainers
13
Seat Bottom Tube Ends
Push Seat
Height
Adjuster
Push Seat
Height
Adjuster
#8 x 1.9 cm Screw - 2
• Push each seat height adjuster to be sure they are completely
on the seat bottom tubes.
• Insert a #8 x 1.9 cm screw through each seat height adjuster
and the ends of the seat bottom tube. Tighten the screws.

8
8
8
Assembly
Back and Bottom View
Seat Bottom Tube Ends
14
Seat Height Adjusters
• From the back and bottom of the assembly, insert a #8 x 1.9 cm
screw through both seat height adjusters and the ends of the
seat bottom tube. Tighten the screws.
#8 x 1.9 cm Screw - 2
15 Back and Bottom View
Hole
Pad
Hole
Elastic Loops
Elastic Loops
Front View
• Lift the assembly upright.
• From the front of the assembly, place the pad onto the seat.
• Lift the bottom of the pad. Insert the two elastic loops on the
pad through the holes in the seat bottom.
• From the back and bottom of the seat, hook the elastic loops to
the tabs on the seat.
Tabs

9
Assembly
Shoulder Portion
16
• Insert the crotch belt through the slot in the pad. Make sure
the crotch belt is not twisted.
• Fold the top of the pad down.
• Remove the shoulder portion of the waist/shoulder belts by
feeding them through the slots in the seat back.
17
• Lift the top of the pad.
• Thread the waist/shoulder belts through the bottom slots in the
back of the seat pad.
Bottom Slots



Slot
Crotch
Belt
18
• Fit the top of the pad over the seat back.
• Fold the bottom edge of the pad under the edge of the seat
bottom to fasten it.
• First, insert the shoulder portion of the shoulder/waist belt
through the slots in the headrest pad. Then, insert
the shoulder portion of the shoulder/waist belt through the
slots in the pad and seat back.
- Use the lower shoulder belt slots for a smaller baby.
- Use the upper shoulder belt slots for a larger baby.
Upper Shoulder Belt Slots
Shoulder Portion
Lower Shoulder
Belt Slots
Headrest Pad Slots

10
Assembly
• Fit the strap on the top of the headrest through the handle.
• Fit the pad strap through the handle and press it to the small
fastener on the back of the seat.
• Fit the headrest strap through the handle and press it to the
large fastener on the back of the seat.
19
Handle Pad Strap
Headrest Strap
Back View
Small Fastener
Large Fastener

Tab
20
Elastic Loop
Tab
Elastic Loop
Belt Ends
• From behind the seat, be sure the shoulder portion of the
waist/shoulder belts are secure in the seat back slots.
• Hook the elastic loops on each side of the pad onto the tabs
in the seat back.
Back View
21
• Fit the storage caddy onto either frame tab.
Frame Tab
Storage Caddy
22
• Fit the basket onto the other frame tab.
Assembly is now complete.
Basket