Grainfather Sparge Water Heater 40L User manual

Instructions
Sparge Water Heater 40L

THANK YOU FOR CHOOSING THE
GRAINFATHER SPARGE WATER HEATER 40L
Get familiar with your equipment by following these quick and easy steps. We recommend reading the following safety
information before use. Please also find enclosed, advice for cleaning and storing your Sparge Water Heater 40L.
SAFETY INFORMATION
• Read all instructions carefully.
• Before use, check the rating label and make sure that the Sparge Water
Heater voltage is t for your outlet voltage.
• The earth terminal of the plug should be connected to the earth block
of the power supply.
• Do not use the Sparge Water Heater if the cord or plug is damaged.
If damaged, please replace before use.
• Switch the o button and the power outlet, before unplugging.
• Do not move the product while in use.
• Grasp the plug when you remove it. Do not pull the cord.
• Do not let the power cord hang over the edge of a table or counter.
• Do not operate the unit without water.
• Do not place near a gas cooker, electric burner, heated oven, or other
re sources.
• Keep the power cord and plug away from water.
• Unplug the power cord from the outlet and let the plug cool before cleaning.
• Switch the unit o and unplug the power cord after use.
• Do not use this appliance outdoors.
• Do not use this product with a power extension cord as an
overload may occur.
• The appliance is only to be installed in locations where it can be overseen
by trained personnel.
• Never leave the unit unattended while in operation.
NOTE: Not following the safety information above may void your warranty.

Before assembling this product, you will need
a Phillips screwdriver.
INSTALLING THE LID
1. Place the handle on the top of the lid.
2. Take the screw and thread on the stainless-steel washer
then the silicone washer.
3. Using a Phillips screwdriver, tighten the screw through
the hole in the lid and into the threaded hole in the handle.
ASSEMBLING THE TAP
1. Remove the stainless-steel nut and rubber gasket
from the ball valve tap. From the inside, put the taps
threaded shank through the bottom hole on the Sparge
Water Heater.
2. Place the silicone washer on the threaded shank on the
inside of the Sparge Water Heater.
3. While holding the tap with one hand to ensure that you
keep the tap facing the right direction, install the nut onto
the threaded shank.
4. Tighten the nut to just beyond nger tight.
5. Test for leaks by lling the unit with enough water
to cover the shank.
6. If there are leaks, ensure that the silicone washer
is at and centred on the shank.
HOW TO USE
1. Remove the lid and ll the Sparge Water Heater with
tap water. Do not ll past the ‘max’ level indicator on
the inside of the unit.
2. Replace the lid and plug the unit into a power socket.
3. Press the ‘on’ switch. The heating light will illuminate
and the water will begin to heat.
4. Set the required temperature on the thermostat dial.
Once the temperature has been reached, the ‘keep
warm’ light will automatically switch on and the
water will be kept at the specic temperature
until required.
NOTE: The thermostat has a hysteresis of 5°C (10°F),
so it is important to have a thermometer to check the
temperature and to make sure that the water is at
75°C (167°F).
5. Use the tap to dispense the water.
DIAGRAM
ASSEMBLY
Thermostat
keep warm
and heating
lights
Easy to read water
level indicators
INSIDE with a dead
space of 2.5L.
on/off
switch
Ball valve tap

• Do not use a high-pressure washer when
cleaning. The product must not be immersed
in water or liquid.
ADVICE FOR CLEANING & STORAGE
• Always disconnect the appliance before cleaning.
• For the rst clean, rinse with clean water to
remove any dust and cardboard debris.
• After use, the appliance should be cleaned
immediately. If the remnants of wort and malt
appear on the surfaces, do not let these dry out as
this will signicantly complicate the
cleaning process.
• All stainless-steel components can be cleaned
using a conventional, unscented detergent.
Abrasive agents and sponges/brushes could cause
scratching, and are not suitable for use. Ideally,
use a dish brush to clean the base of the unit.
• Clean the valve and all components.
• After cleaning, allow the product to air dry
or use a towel.
• Do not store in a damp area as this could
cause damage to the product.
GET IN TOUCH:
Email: [e-mail]
NZ [phone]
AU [phone]
US [phone]
UK/EU [phone]
RESOURCES: Check out our YouTube Channel for helpful videos. For more information visit our FAQ’s page
shop.grainfather.com/index.php/faq.
6. Always make sure that approx. 3 cups of water
remain in the appliance to avoid it overheating.
NOTE: This device has a thermal cut o switch
to prevent dry boil. If the element overheats, the
thermostat will automatically turn o the machine.
If you experience overheating, please wait a few
minutes for the appliance to cool down and reset
the temperature.
INSTRUCTIONS FOR SAFE USE
• Do not remove the lid while boiling.
• Position the lid so that steam is directed away
from the handle.
• Do not carry the Sparge Water Heater while it
contains liquid.
• Do not overll the product as boiling water
may overow.
• If the power supply cord is damaged, it must
be replaced by the manufacturer or its service agent,
or a qualied person to avoid a hazard.
• This appliance should not be used by
children. Keep the product and its cord out
of the reach of children.
• This product is not intended for use by persons with
reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been
given supervision or instruction concerning
the use of the appliance by a person responsible
for their safety.
www.grainfather.com
Version: 2
IMPORTANT SAFEGUARDS:
READ AND FOLLOW ALL INSTRUCTIONS
CAUTION – Risk of res and electric shock.
– Replace only with genuine Grainfather cord set.
– Do not immerse in water.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR
FUTURE REFERENCE
FOR COMMERCIAL AND INDOOR USE ONLY
WARNING
AVERTISSEMENT
RISK OF ELECTRIC SHOCK . DO NOT OPEN.
RISQUE DE CHOC ÉLECTRIQUE. NE PAS OUVRIR
Download the FREE
Grainfather App
HOW TO USE CONT.
TECHNICAL SPECIFICATIONS
Volume: 40L
Voltage: 220V-240V (110V-120V US)
Power: 2300W (1500W US)
Frequency: 50Hz/60Hz
Dead space: 2.5L