GRD Systems Bliss User manual

BLISS
BLISS
User's Manual
Thank you for choosing
GRD products

BLISS
User's manual 21
Package
Monitor – 1pc.
Door panel - 1pc.
Wall mounting bracket with screws – 1pc.
Table mounting bracket – 1pc.
Power adaptors – 2pcs.
User's manual – 1pc.
Monitor keys
1. Microphone
2. Display
3. Contrast tuning
4. Brightness tuning
5. Talk volume tuning
6. ”Choose call melody” button
7. ”Answer” button
8. ”Open lock” button
9. „Call melody volume”button
10. „Monitor” button
11. Speaker
Door panel keys
1. Microphone
2. Infrared backlight
3. Camera
4. Speaker
5. ”Call” button
6. Name plate
1
4
3
2
6
5
1
4
3
2
6
5
7
8
9
10
11
Monitor Specication:
Display 4" LCD
Resolution 320 x 240 pixels
Input voltage ~100-240V (50-60 Hz)
Output adaptor voltage 5V, 1.0 A
Power consumption 5 W in working mode
0,1 W in standby mode
Door panel system wireless
Frequency range 2,402 - 2,483 GHz
Operating distance up to 300 m. open area
Image compression MJPG, up to 10-16 frames/sec.
Dimensions 190 mm(H)> х 125mm(W) х 26mm(T)
Temperature range -5˚С ~ 40˚С
Door panel specication:
Camera CMOS
Night mode Infrared backlight
Viewing angle 92˚
Input voltage ~100-240V (50-60 Hz)
Output adaptor voltage 13V, 1.2 A
Power consumption 10 W in working mode
0,1 W in standby mode
Dimensions 142 mm(H)> х 98mm(W) х 38m(T)
Temperature range -20˚С ~ 40˚С

Incoming calls answer
When a visitor prsses door panel buttton, the indoor monitor will chime. The screen will show the image
from the door panel. Press button to talk with the visitor . If you want to unlock the door for the
visitor during conversation, press button.
Door unlock icon will be shown on the left upper corner of the screen . The unlock delay time is 5 seconds if
jumper on the rear side of the panel have been installed. To end current call, press button.
If you don’t want to talk with the visitor, press button twice while monitor calls.
If you want to unlock the door but don’t want to talk with the visitor, press button while calling, then
press button to open lock and press button again to end current call.
Door panel viewing
To view the image from the door panel, shortly press button in standby mode. Press button again
to end viewing.
If you want to talk with the visitor while viewing door panel, just press button. To end current talk,
press button again.
BLISS
User’s manual 43
Schematic diagram:
GRD Bliss door phone connection diagram
Characteristics:
• 16 polyphonic melodies
• 2 types of monitor mounting: wall mounting and table mounting
• volume, contrast and brightness tuning
• current date and time screensaver
• mechanic and electronic door lock control directly from the door panel
• sensor keyboard
• additional ”open lock” button connection near the door panel
Installation instructions
• Choose monitor and door panel position (recommended installation height is
between 145cm and 160cm).
• Before installtion starts, make sure that the distance between monitor and door panel
covered by wireless signal: connect door panel and monitor power adaptors near
installation place, according to the schematic diagram on the next page and turn on the
power. Press call button on the door panel. Make sure that there are no noises on the
monitor's image. Now you can start installation process.
Door panel installation:
• Make sure that power supply of the monitor and door panel are disconnected.
• Disassemble one screw on the bottom of the door panel and unplug wall mounting
bracket. Fix the bracket on the wall by the screws.
• Connect 13V power adaptor plug to the door panel power connector according to the
schematic diagram.
• Install door panel into wall mounting bracket and assemble the screw on the bottom
side of the panel to x it.
Door panel installation:
• Disassemble metallic wall mounting bracket from the monitor by pushing it downside
and out from the back panel of the monitor.
• In case of using table mounting bracket you should connect two plastic parts of the
table bracket with each other and x it by two screws. Then insert table bracket under
plastic toothes near bottom assembly holes of the metallic bracket on the backside of
the monitor. Connect 5V power adaptor plug to the monitor power connector accord-
ing to the schematic diagram.
• In case of using wall mounting bracket, fix metallic bracket on the wall by three screws.
Connect 5V power adaptor plug to the monitor power connector according to the
schematic diagram and mount the monitor on the wall.
• Turn on the power of the monitor and door panel.
* Jumper installed - unlock time is 5 seconds
Jumper removed - unlock is active until user holds button on the monitor
Elec.-Mechanical lock
Open lock
button
12V
Power Button Lock Jumper*
OFF GND ON
VCC GND
Power adaptor
~100-240V
13V, 1.2A
Power adaptor
~100-240V
5V, 1.0A
Door panel
Monitor
Power
GND
VCC
2,4GHz

Brightness / contrast and talking volume adjust
Upper part of the monitor right panel has three adjustments. Upper adjustment
changes image contrast of the monitor. Middle adjustment changes image brightness
of the monitor. Bottom adjustment changes talk volume.
Date and time settings
Press and hold button for 3 seconds in standby mode to enter date and time
settings menu:
Shortly press or button to change current number under the marker. Use
button to move the marker between numbers. After all settings have been made,
press button to save and exit date and time settings menu.
Melody volume and ringtone settings
Press and hold button for 3 seconds in standby mode, melody will start ringing.
Shortly press button several times to adjust melody volume of the monitor or
press button to change current ringtone. 16 polyphonic ringtones are availble in
the monitor's memory. After all settings have been made, press button to save
and exit into standby mode.
Same way you can change melody volume and ringtone while monitor calling.
Date and time screensaver
In standby mode shortly press any button on the keyboard exept button, to view
sceensaver with current date and time.
BLISS
User's manual 65
Safety Instructions
1. Do not install near other electronic equipment such as computers, TV, video recorder as
this may cause radiated interference to the unit.
2. Do not disassemble the unit.
3. Do not spray water on the indoor unit. Do not keep the outdoor unit where it will be
exposed to extreme moisture.
4. Do not drop or shock the unit, dropping can result in failure to operate. Circuit boards can
crack and may not survive the impact.
5. Remove the power cord from the wall socket when unit is not used for long periods
6. Do not cover the ventilation holes with clothing, paper, curtains etc.
7. Keep minimum distance 5cm around the apparatus for sucient ventilation.
8. This apparatus is designed for middle climates. Do not use in high humidity, dusty or
dirty areas. The electronics may be contaminated.
9. To disconnect or isolate the unit, switch o at the socket or remove plug from wall socket.
Please ensure the plug and socket is easily accessible.
10. Do not use harsh chemicals, cleaning solvents or strong detergents. To clean, wipe with a
damp cloth from time to time.
Warranty
Warranty period is 12 months from purchaseing.
Warranty void if unit was damaged by the fault of the custumer.
Warranty void if the sticker on the backside of the unit was broken.
Life time of the unit depends on it's maintainance and carefull using.
Time: 14 : 47
Date:2012\09\07
Time and date
1