Green Star Avenger User manual

Document Name
Avenger Installation Instruction
Template Number
GSPDPAD46
Document Number
PDPAD460000607
Document Owner
ESS Department
Template Rev
01
Document Rev
AA001
GSRD | Company Confidential Page 1 of 2
PRODUCT DIMENSIONS
W ARNING
Risk of electrical shock. Disconnect power before
servicing or installing luminaire.
W ARNING
Risk of injury. Wear safety glasses and gloves during
installation and servicing.
W ARNING
Risk of injury or damage. Luminaire will fall if not installed
properly. Follow installation instructions.
Important Notice
These instructions are not intended to cover all details or variations
in the products nor do these instructions provide for every possible
contingency concerning the installation, operations, or maintenance
of the luminaire. Should additional information be required, contact
your Green Star Research & Development (India) Pvt Ltd.
The contents of this manual shall not become a part of or modify any
prior or existing agreement, commitment, or relationship. The sales
contact contains the entire obligation of Green Star Research &
Development (India) Pvt Ltd. Green Star Research & Development
(India) Pvt Ltd.’s standard limited warranty is the sole warranty
obligation of Green Star Research & Development (India) Pvt Ltd.
and any statements contained herein do not create new warranties
or modify the existing warranty.
Any electrical or mechanical modifications to the luminaire without
the prior written consent of Green Star Research & Development
(India) Pvt Ltd. may void all warranties or other safety certifications.
Unauthorized modifications may also result in safety hazards or
damage to the luminaire. Misuse of the luminaire could result in
injury and equipment damage. In no event will Green Star Research
& Development (India) Pvt Ltd. be responsible or liable for direct,
indirect, special, or consequential damage or injury that may result
from the misuse of the luminaire.
BEFOREYOU BEGIN
Read these instructions completely and carefully.
Save these instructions for future
use.
254 mm (10")
109 mm (4.3")
635 mm (25")
163 mm (6.42")

Document Name
Avenger Installation Instruction
Template Number
GSPDPAD46
Document Number
PDPAD460000607
Document Owner
ESS Department
Template Rev
01
Document Rev
AA001
GSRD | Company Confidential Page 2 of 2
Inspection
 The packaging has been designed to protect the luminaire from damage during
transit. Inspect luminaire for damage before installation.
Mounting the Luminaire on the Pole
 Open the wiring compartment door using the quick release screw. Do not remove
the screw completely. (see figure a).
 Slide the luminaire onto the pole and rest it on the cast leveling steps as required to
properly level the luminaire. Use optional bubble leveler to achieve the proper side
to side position of the luminaire. After final adjustments are made, tighten the
mounting bracket bolts to prevent any movement or rotation. (see figure b and c).
 Wiring
o NOTE: Make sure that all electrical connections are in accordance with the
National Electrical Code (NEC), and any applicable local code requirements.
o NOTE: Check the rated input voltage on the luminaire product label, and
verify that the supply voltage meets the product requirements.
o Connect the wire to terminal block according to the wiring diagram.
(see figure d).
o For Dimming Option – Connect external DC supplied positive wire to the
Purple Dimming wire and negative DC supplied wire to Grey Dimming wire.
o When making electrical connections, make sure that the ground wire on the
supply side is connected to the ground wire of the luminaire. Under no
circumstances the ground wire should be left disconnected. This will cause
the luminaire to fail, and the luminaire will not be covered under warranty.
 After all connections have been made, close the wiring compartment door, and
make sure it is securely fixed. (see figure e).
 Optional: For NEMA base Positioning - Loosen the 2 fasteners and Rotate NEMA
base to point NORTH. Do NOT over-loosen fasteners to get dislodged from base.
Do NOT leave base untightened to avoid malfunctioning and ingress
Maintenance
 Depending on environmental conditions it may be necessary to clean the lens in
order to maintain a high-efficiency lens. (Use solvent-free cleaners)
Storage
 Prior to installation, the luminaire should be placed in a covered, dry storage. The
storage location should not exceed the normal operating temperature of the
luminaire.
Figure a
Figure b
Figure c
Figure e
Figure f
Figure d