manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. ENSA
  6. •
  7. Lantern
  8. •
  9. ENSA LEDBT18WS2 User manual

ENSA LEDBT18WS2 User manual

ENSA Standard LED Batten - Use & Installation Guide Applicable Models: LEDBT18WS2, LEDBT36WS2, LEDBT18WSE, LEDBT36WSE For full product information, visit www.ensalife.com
1. Installation Instructions 2. Installation Procedure
Please read these instructions carefully before
installation and keep for future reference.
• Always turn o supplied power to the LED batten
before performing installation or maintenance.
• This LED batten must be earthed.
• This LED batten is complete without a ballast.
• Drilling into the batten body will void the
warranty - this batten should only be mounted
by surface mounting clips.
• Installation and wiring must only be performed
by a qualied, licensed electrician.
• Please ensure rated voltage and frequency of the
batten is compatible with the power supply.
• Clean with soft cotton cloth only, do not use any
chemical solvents when cleaning this batten.
• In case of tting failure, switch o power to the
batten and wait for the tting to cool. Perform
steps 2.3 - 2.8 in reverse to take down the tting.
The mounting centre points for the LED batten are
located on the included mounting clips. Choose
a suitable location and x the clips using included
wall plugs & screws.
Before tting the batten to the mounting clips,
ensure lock toggles are attached to the body.
Secure the array board with rotating locking clips.
Fit the cover to the body, close all lock toggles to
complete installation.
Switch on main power to test.
Please keep these instructions in a safe place for
future reference.
Insert main power supply through the gland then
tighten the lock nut to the batten body. Make sure
there is sucient cable to reach the terminal block.
Attach the safety cable to stop the array board from
falling; enables hands free use.
Mounting clips span can be slightly adjusted to t
to dierent installation tolerances. The light can also
be wall mounted.
2.1 Mounting Clips
2.4 Lock Toggles
2.8 Secure Array Board & Close Cover
2.9 Test & Complete
2.5 Running Power Cable
2.6 Array Board Safety Cable
2.3 Ceiling or Wall Mounting
See table and matching diagram below for
mounting information
Model Length (A) Fix Span (B) Clips
LEDBT18WS2 655mm 470mm 4
LEDBT36WS2 1260mm 900mm 8
LEDBT18WSE 655mm 470mm 4
LEDBT36WSE 1260mm 900mm 8
1.1 Important Notes
1.2 Installation Specications
Centre points (refer 1.2 table)
1
1
2
2
Connect as illustrated, ensuring the cable is secure
with no bare wires and correct polarity.
2.7 Connect Supply to Terminal Blocks
ENSA Standard LED Batten - Use & Installation Guide Applicable Models: LEDBT18WS2, LEDBT36WS2, LEDBT18WSE, LEDBT36WSE For full product information, visit www.ensalife.com
3.1 Detection Area (Sensitivity)
DIP Switches 1 & 2
Congure the 360° microwave motion sensor
sensitivity to tailor the motion detection area of the
batten to your exact specications.
Default setting: 100% (16m radius max. Detection)
3. Sensor Conguration 4. Emergency Mode Conguration
Tailor the ENSA Emergency LED Batten to a multitude of
environments & applications. Congure detection sensitivity,
on-time delay, dimming level and 2-stage dimming control via
DIP switches on the unit.
The backup battery provided with your ENSA Emergency LED Batten is designed to provide light uptime
in the event of an emergency. The battery ships disconnected to prevent battery discharge. See below for
default settings:
• LEDBT18WSE - 3000mAh LiFePO4 backup battery, set to 3.6W in emergency (5hr uptime)
• LEDBT36WSE - 3000mAh LiFePO4 backup battery, set to 3.6W in emergency (5hr uptime)
Below is the conguration panel for the backup battery, located in the middle of the batten.
3.2 Hold Time (On-time delay)
DIP Switches 3 & 4
Congure the duration that the light stays at maximum
brightness after the last detected motion.
Default setting: 90 seconds
3.3 Twilight Ratio (Dimming level)
DIP Switches 5 & 6
Congure the dimmed illumination level after the last
detected motion and after the hold time has expired.
Default setting: 20% (of maximum brightness)
3.4 Twilight Time (Dimmed-time delay)
DIP Switches 7 & 8
Congure the duration that the light stays at dimmed
brightness. It can be set to stay dimmed (never o) or
turn o instantly (never dim).
Default setting:
∞
s (stays dimmed, never o)
DIP Switch Conguration
1 2 Max. Detection
I ON ON 100% (16m)
II - ON 75% (12m)
III ON - 50% (8m)
IV - - 25% (4m)
DIP Switch Conguration
3 4 On-time Delay
I ON ON 5s
II - ON 30s
III ON - 90s
IV - - 180s
DIP Switch Conguration
5 6 Dimming Level
I ON ON 20%
II - ON 40%
III ON - 60%
IV - - 100%
DIP Switch Conguration
7 8 Dimmed-time Delay
I ON ON 0s (instant o, no dim)
II - ON 90s
III ON - 180s
IV - -
∞
s (light remains on)
Test
Charging Main Power
Set
4.1 Test Button
Allows for maintenance testing of backup battery
By pressing and holding TEST, the batten will switch to battery power to simulate emergency lighting,
even when main power is available. Release the test button to return the light to main power. Performing
regular battery maintenance checks is recommended.
4.2 Charging LED (Red)
Indicates that the backup battery is charging
• LED constant on: Battery on high rate current charge
• LED 1s on then 1s o: Battery on intermittent or trickle charge
• LED 2 ashes then 2s on: At last self-test, forecast battery uptime was less than 90 minutes.
Note: Upon full battery discharge, the batten light may icker momentarily while recharging.
4.3 Power Supply LED (Green)
Indicates that the batten has main power supply
LED On: Main power supplied
LED O: No main power available

This manual suits for next models

3

Other ENSA Lantern manuals

ENSA SSL-B Series User manual

ENSA

ENSA SSL-B Series User manual

ENSA LOL-A16 S Series User manual

ENSA

ENSA LOL-A16 S Series User manual

Popular Lantern manuals by other brands

GEV LPH 011014 manual

GEV

GEV LPH 011014 manual

Nave 52124 manual

Nave

Nave 52124 manual

Coleman 639C700 owner's manual

Coleman

Coleman 639C700 owner's manual

Jaykal JLS68103-G60-ACTR installation instructions

Jaykal

Jaykal JLS68103-G60-ACTR installation instructions

Dymond Solar Motion Light user manual

Dymond

Dymond Solar Motion Light user manual

StreamLight LITEBOX user manual

StreamLight

StreamLight LITEBOX user manual

SOLTRON XS-35 XTRA SERIES operating instructions

SOLTRON

SOLTRON XS-35 XTRA SERIES operating instructions

Makita BML184 instruction manual

Makita

Makita BML184 instruction manual

TP-Link Kasa Smart quick start guide

TP-Link

TP-Link Kasa Smart quick start guide

olympia electronics Double Easy Light GR-391/L quick start guide

olympia electronics

olympia electronics Double Easy Light GR-391/L quick start guide

Boyd Belvedere I installation instructions

Boyd

Boyd Belvedere I installation instructions

Lucetta Lighting CELESTE installation guide

Lucetta Lighting

Lucetta Lighting CELESTE installation guide

IDEAL INDUSTRIES CREE LIGHTING XSP Series manual

IDEAL INDUSTRIES

IDEAL INDUSTRIES CREE LIGHTING XSP Series manual

ETC IRIDEON AR500 Disassembly instructions

ETC

ETC IRIDEON AR500 Disassembly instructions

LiteXpress CAMP 33 user guide

LiteXpress

LiteXpress CAMP 33 user guide

Fusion 16148 quick start guide

Fusion

Fusion 16148 quick start guide

WE-EF RBL640 Installation and maintenance instructions

WE-EF

WE-EF RBL640 Installation and maintenance instructions

Wetelux 874256 instruction manual

Wetelux

Wetelux 874256 instruction manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.