greenPRO GP1200 User manual

PROUDLY AUSTRALIAN
OWNED & OPERATED
GP1200
6-in-1 seeder
MANUAL

ADDRESS
Greenpro Solutions Pty Ltd
9 Research Street
Coolum Beach
QLD 4573
PHONE
1800 768 748
ONLINE
[e-mail]
www.greenpro.com.au
READ THIS OPERATION MANUAL CAREFULLY BEFORE
ATTEMPTING TO OPERATE THE UNIT
No part of this manual may be reproduced without
written permission.
All information in this manual is based on the latest
product information available at the time of printing.
Greenpro Solutions Pty Ltd
GP1200 6-IN-1 Seeder
Operations and Guidelines
Updated: July 2022
Original Instruction
All information, illustrations and specifications in this manual are based on the latest information at the time of publication.
The right is reserved to make changes at any time without notice.
COPYRIGHT© 2022
greenPRO
Greenpro Solutions Pty Ltd
All rights reserved
Previous Editions
COPYRIGHT© 2022
WARNING

On behalf of greenPRO we would like to thank you for
investing in the GP1200 6-IN-1 Seeder
Every greenPRO implement is manufactured to meet our
high Australian standards so that we can provide our owners
with the best product and service possible. Our aim is to
offer the right solutions to combat challenges so that you
can enjoy the lifestyle you’ve worked hard to create.
As an Australian owned business, your investment has
enabled our every success. Over 30 years combined active
involvement in this community has allowed our team to
provide solutions to combat challenges that Australian
farmers face in agriculture today.
We appreciate your patronage and hope you enjoy many years
of safe and satisfied use of your implement.
This manual should be considered a permanent part of your
greenPRO GP1200 6-IN-1 Seeder and stored in a safe place
for future reference.
Welcome to where the grass is greener.
CONGRATULATIONS,
YOU’RE A PRO.

SECTION 1
System Overview
SECTION 2
Set Up and Unpack
SECTION 3
Basic Operational Information
SECTION 4
Seed Flow Control Handle
SECTION 5
Available Attachments
SECTION 6
Dimensions and Specifications
SECTION 7
Maintenance
SECTION 8
Trouble Shooting Guide
SECTION 9
Helpful Planting Hints
SECTION 10
Your Notes
1
2
5
7
11
12
13
14
16
19
TABLE OF
CONTENTS
GP1200 6-in-1 Seeder
OPERATION MANUAL
SECTION 11
Warranty Policy
Warranty
Registration Form
Contact
20
24
25

1
GP1200 6-IN-1 SEEDER OPERATION MANUAL
1SYSTEM OVERVIEW
12v
Actuator
Rear seed
hopper
Seed ow
control handles
RollerDrawbar top
link levelling
adjustment
Drag bar
and mesh

2
GP1200 6-IN-1 SEEDER OPERATION MANUAL
1SYSTEM OVERVIEW
Disc plough
assembly
Electric seeder
brush motor
Optional extra
seed hopper
Wheels for moving
the seeder in
transport mode
Radio
Receiver
Standard
seeder box

2
GP1200 6-IN-1 SEEDER OPERATION MANUAL
2set up and unpack
The GP1200 will arrive with the tow
bar packed in the stowed position.
Pull both the drawbar and turnbuckle
down until the turnbuckle head
locates in the top link position on
the drawbar. When located correctly,
insert the top link & linch pins to
lock drawbar in position. Crank the
turnbuckle handle to adjust the
drawbar to your desired height.
To connect your GP1200 to your
tow vehicle, rstly, position tow ball
underneath the tow hitch. Lift the
hitch handle until it locks into the
open position and lower the drawbar
onto the tow ball by cranking the
turnbuckle. The handle on the tow
hitch should lock onto the tow ball
when located. If this does not occur,
raise drawbar, and repeat step until
locked correctly in position. You may
need to physically push down on the
tow hitch to force engage the tow
ball lock.

3
GP1200 6-IN-1 SEEDER OPERATION MANUAL
15 Amp blade fuse holder.
Plug your Anderson plug into the
Anderson plug attached to the
control box wiring harness.
Hook up your wiring harness to your
12 volt battery supply. Red wire is +
and black wire is -.
Before you tow your GP1200, connect
power to the unit using the supplied
battery extension cable, connected
through the Anderson plug located
near the drawbar pivot. Using the radio
remote supplied in your machine kit,
lower the wheels until the plough discs
are approximately 150mm clear of the
ground.
Note:
The axle legs are painted red to
indicate a maximum safe tow height.
2SET UP AND UNPACK

4
GP1200 6-IN-1 SEEDER OPERATION MANUAL
2SET UP AND UNPACK
13mm spanner / socket
Brush Cover
10mm spanner / socket / 5mm hex key & 1/8” hex key
Seed Brush
REQUIRED TOOLS:
AS OF OCT 2019:
CHANNEL 1 – ON/OFF switch for
auger brush system in the FRONT
seeder box.
CHANNEL 2 - Operation to LIFT
seeder wheels which in return drops
the cutting discs further into your
soil.
CHANNEL 3 - Operation to DROP
seeder wheels which lifts the cutting
discs further out of the soil.
CHANNEL 4 - ON/OFF switch for
auger brush system in the REAR
seeder box.
remote control for
Seeder Operations
RADIO TRANSMITTER
TIP: Always use a high quality 9volt battery to power your radio transmitter. Replace the
9volt battery at least every 3 months OR more often with continual use. As the battery
voltage drops, the effective radio range will drop accordingly.

5
GP1200 6-IN-1 SEEDER OPERATION MANUAL
PLEASE READ OPERATING INSTRUCTION CAREFULLY BEFORE USE.
› Do not turn GP1200 with plough discs engaged. Lower axle before turning to reset
for your next pass.
›Do not sit, stand or ride on the seeder while in use
› Maximum capacity of the seeder box seeder 1200 is 25kg per box
› Do not put hands in seed box while seeder motor is in the on position
› Do not put lime in seeder
› Only use granulated fertiliser
› Keep hands and feet clear when raising and lowering unit
› Keep hands and ngers clear when raising or lowering the drag and/or press
roll to avoid pinching
› The GP1200 tow hitch accommodates a 50mm, ensuring compatibility with most
standard tow vehicles, including ATVs, UTVs and Tractors. We do not recommend
using a car, as it impedes your view of the machine whilst in operation.
› Seeder is designed for off road use. DO NOT tow on public roadways.
› Make sure that the battery clips are connected to the proper terminals to avoid
damage to your electrical system and/or your UTV/tractor.
(Red = positive terminal. Black = negative terminal)
› Avoid coming in contact with any other metal parts on the vehicle when
connecting the battery clips to your battery.
› Adding lime or non-granular fertiliser to your seeder will void the warranty of
“all” parts associated with the seeding system.
› In addition the density of Lime is much greater than seed and can bind your
brush shaft causing the motor to “burn out”.
› Seed is far lighter and will not compact around your Seeder Brush and cause
damage to your seed motor like lime/non-granular fertiliser can.
› 10km max tow speed
DO NOT OPERATE YOUR SEEDER ON INCLINES
GREATER THAN 10°.
WARNING
BASIC OPERATIONAL
3INFORMATION

6
GP1200 6-IN-1 SEEDER OPERATION MANUAL
50MM BALL HITCH
The GP1200 comes with a hitch to t
a standard 50mm trailer ball. Ensure
that the tow hitch is rmly secured
in place before tilling to prevent
separation from tow vehicle.
TOP LINK HOOK-UP
The Down Pressure System is
designed so the user can apply
disc pressure to either the front
or the rear of the unit. (Unit is
recommended to be set level to plant
to get correct coverage with the
chain drag and/or press roller).
PRESS ROLLER
The roller is designed for compaction
of the soil over the seed thus
increasing seed to soil contact for
optimal germination of what has
been planted. The roller can also
be used for added weight during
tillage. This is achieved by
leaving the roller in the folded
position and resting it over the
front disc.
ELECTRIC LIFT
The Electric Lift serves many
purposes; one is the ability to rise
& lower your unit for transport,
the other is to gauge the depth
of discing and or planting. This is
activated by the UP/DOWN switch
that is located on the control box.
WHEEL ASSEMBLY
The Wheel Assembly is how the unit
travels when in transport mode, and
is connected to the Electric Lift to
raise and lower the unit.
DISC PLOUGH ASSEMBLY
The Disc Plough is set in a manner
that soil disturbance is minimal
and mimics a “cross cut” affect for
greater mixing of all types of the soil.
3BASIC OPERATIONAL INFORMATION

7
GP1200 6-IN-1 SEEDER OPERATION MANUAL
The Seed Control Handle allows you
to adjust the rate of seed dispensed
depending upon the size seed you
are planting.
Actual seed hole gauge size opening
in seed box and scale arrow pointer.
The 0-5 Scale helps in determining
the width of the opening. Smaller
seed will be the low end, 0-2, and
larger seed will be the high end, 3-5.
Please refer to seed chart on page 18.
IT IS RECOMMENDED TO USE A LEAF BLOWER TO BLOW OUT
THE SEED BOXES AFTER EACH BOX OF SEED IS DISPENSED,
AND AFTER FERTILISER DISPENSE.
CAUTION
4sEED FLOW CONTROL HANDLE
The electric seed box motor is
activated by the remote ON/OFF
switch. This motor drives the brush
auger that dispenses the seed.
SEEDER MOTOR

8
GP1200 6-IN-1 SEEDER OPERATION MANUAL
This receiver is located on the rear of
the unit and is secured by a 1/2” x 3
hitch pin with clip. You can adjust the
height of the drag bar to allow more
or less metal grating to be in contact
with the ground.
Drag Bar Receiver
The drag bar and/or harrow mesh
is used for either leveling uneven
areas or for covering smaller seed
that only require a minimal amount
of coverage to germinate. You can
adjust the amount of harrow mesh
swing allowed by putting more or
less tension on the side chains.
Drag Bar with
Harrow Mesh
4SEED FLOW CONTROL HANDLE
The manual remote is used to raise
and lower the unit and to switch
the seeder/s motor ON and OFF.
Replacement Fuse—30 Amp Blade
Fuse.
Manual REMOTE

9
GP1200 6-IN-1 SEEDER OPERATION MANUAL
4SEED FLOW CONTROL HANDLE
The plates can be adjusted vertical/
horizontal or anywhere in between
for desired disbursement of seeds
being planted. The more vertical the
angle the seeds will drop directly
behind the Seeder. The more
horizontal the angle and the seeds
will scatter wider behind the Seeder.
Adjustment bolts for changing the
angle of the disbursement plate.
Plates for Seed
Disbursing
The GP1200 comes with a manual remote as well as a radio remote so you can operate to your
personal preference. The radio remote is tted standard as the primary controller for your unit.
To connect your manual remote, you will need to unplug the radio box connections near the
drawbar pivot, and connect the manual controller in their place.
Switch for lowering or raising the
height of the disc plough assembly.
Seeder control box.
ON/OFF switch for optional middle
seed box.
ON/OFF switch for rear seed box.

10
GP1200 6-IN-1 SEEDER OPERATION MANUAL
The roller is designed to pack the soil
for greater seed to soil contact. The
Spring/Chain is designed to add even
more compaction, if desired.
Compaction Roller
Make sure to grab the chain only
when adjusting the roller tension.
If you grab the spring you can
pinch your fingers.
CAUTION
4SEED FLOW CONTROL HANDLE
Remove the auger brush cover by
unscrewing the 4 wing nuts and
bolts to inspect the brush rotational
function. Check seed box controls on
radio remote/control box to ensure the
unit is functioning correctly.
Seed brush auger with brush cover
removed. The seed brush is designed
to move, mix, and dispense seed and
granular fertiliser to the tear drop
gate holes in the bottom of the seed
box hopper. This ensures an even
distribution of seed/fertiliser as well as
blending mixed sized seeds.

11
GP1200 6-IN-1 SEEDER OPERATION MANUAL
›The attachment mounts in place of the rear
box grain deector and come with the
capacity to adjust heights and proximity to
the plough discs for precision sowing.
› The addition of the direct seed drill
attachment allows for sowing of seed such
as corn, where greater seed sowing depth is
required.
Direct seed drill attachment
5AVAILABLE ATTACHMENTS

12
GP1200 6-IN-1 SEEDER OPERATION MANUAL
Dry Weight Single Seed Box 372 KG
Dry Weight Dual Seed Box 405 KG
Width 1200 mm
Height 1090 mm
Length completely folded 1800 mm
Length with tow bar folded down 2500 mm
Length with roller bar extended 3350 mm
System voltage 12 Volts
System wiring harness fuse 30 Amp
System wiring harness length 4000 mm
Tyre Pressure Max Pressure – 22 PSI
Remote control 9-volt battery
Maximum cutting width 1220 mm
Maximum cutting depth 135 mm
Heavy Duty Notched Discs with Sealed Bearings 12 x 406 mm
Maximum seed capacity per Seed Box 25 KG
Recommended ATV 500 cc or larger 4WD
6DIMENSIONS & SPECIFICATIONS

13
GP1200 6-IN-1 SEEDER OPERATION MANUAL
› Check tyre pressure every
10 hours of use. 22 PSI is the
recommended pressure.
› Clean Seeder Boxes and Seed
Brush often. If using granular
fertiliser the Seeder Boxes must
be hosed out after each use to
prevent the brush from jamming.
› Inspect seeder brushes for wear
when cleaning and replace as
necessary.
› Check for wear for hitch
7MAINTENANCE

14
GP1200 6-IN-1 SEEDER OPERATION MANUAL
PROBLEM POSSIBLE CAUSE & SOLUTION
Electric lift motor and Seeder Box
Motors are not working
Check the wiring loom to make sure
it is plugged in to the 12 volt power
source.
Check the wiring loom for damage.
Repair or replace as necessary.
Check the 12 volt power source to
make sure it is charged. Charge or
replace as necessary.
Check the 30 blade fuse in the wiring
harness. Replace if blown.
Radio box failure.
Electric lift motor is working but
Seeder Box motor is not working
Check wiring harness Deutsch plug to
seeder box motors. Plug in or replace
if necessary.
Possible failure of seeder box motor.
Replace if necessary.
Check fuses in seed box harnesses
(10 Amp)
Electric lift motor is not working but
Seeder Box motors are working
Check wiring harness Deutsch plug
to lift motor. Plug in or replace if
necessary.
Possible failure of lift motor. Replace if
necessary.
Seeder box stops dispensing seeds
Seeder box it empty. Rell with seed
as necessary.
Seeder box brush is jammed with seed.
Empty seeder box and free up seeds
around the brush.
8TROUBLE SHOOTING GUIDE

15
GP1200 6-IN-1 SEEDER OPERATION MANUAL
PROBLEM POSSIBLE CAUSE & SOLUTION
Seeder box stops dispensing
granular fertiliser
Seeder box is empty. Rell with
granular fertiliser.
Seeder box brush is jammed with
fertiliser. Only use granular fertiliser or
the brush will jam every time. Empty
Seeder box and free up fertiliser
around the brush.
Cutting discs have been damaged
Cutting discs have not been raised
when driving over concrete or
pavement. Only allow the rubber tyres
to be in contact when moving over
concrete or pavement.
Electric lift motor travelling guide
posts have become jammed not
allowing the motor to move the
Seeder up or down
The seeder has been driven over
uneven terrain with the cutting blades
too far off the ground causing the
travelling posts to have moved in a
way that they have jammed inside
the guide post. Call greenPRO for
assistance.
Always try to travel with the cutting
discs just above the ground or about
100mm clearance when moving the
Seeder from one location to another.
Travelling with them too high can
cause the travelling guide posts to
bind and jam in undulating terrain.
Seeder is not level or weight is too
far forward or backward on the unit
The gold top link is out of adjustment.
Rotate the top link adjustment handle
to level the unit or disperse the weight
in the desired direction.
SECTION 8 TROUBLE SHOOTING GUIDE