GreenWorks Pro SNC405 User manual
2607902
SNC405
1 DESCRIPTION
1.1 PURPOSE
This machine is used to remove and clear away snow from
pavements, gardens, driveways and other ground-level
surfaces.
1.2 OVERVIEW
1Handle bar
2Bail lever
3Safety switch button
4Chute control rod
5Battery door
6Chute deflector
7Discharge chute
8LED lights
9Scraper
10 Impeller
11 Wheel
12 Quick-release lever
13 Lower handle
14 Upper handle
15 Middle handle
16 Knob
17 Bolt
18 Screw
19 Nut
20 Battery pack
21 Battery release button
22 Trigger
23 Chute-rotation box
24 Switch box
25 Slot
26 Groove
27 Side wear pad
28 Belt
29 Pulley
30 Skid plates
31 Spacer
32 Cam lock
33 Blue LED light
2 GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your battery-
operated (cordless) power tool.
2.1 TRAINING
• Do not allow children under the age of 14 to operate this
tool. Children who are 14 years of age or older must read
and understand the operating instructions and safety rules
in this manual and must be trained and supervised by a
parent.
• Read the operating and service instruction manual
carefully. Be thoroughly familiar with the controls and
the proper use of the power tool. Know how to stop the
unit and disengage the controls quickly.
• Never allow children to operate the power tool. Never
allow adults to operate the power tool without proper
instruction.
• Keep the area of operation clear of all persons,
particularly small children, and pets.
• Exercise caution to avoid slipping or falling, especially
when operating in reverse.
• Do not use on graveled surfaces.
• Dress Properly – Do not wear loose clothing or jewelry.
They can be caught in moving parts.
• Wear appropriate boots when operating the snow thrower.
• Operation of the snow thrower in the hand-held position
is unsafe, except in accordance with the special
instructions for such use provided in the operator’s
manual.
2.2 PREPARATION
• Thoroughly inspect the area where the power tool is to be
used and remove all doormats, sleds, boards, wires, and
other foreign objects.
4
English
EN
㸦㸧
㸪
WARNING
Discard all toxic materials in a specified manner to prevent
contamination of the environment. Before discarding
damaged or worn out Li-ion battery, contact your local
waste disposal agency, or the local Environmental
Protection Agency for information and specific instructions.
Take the batteries to a local recycling and/or disposal center,
certified for lithium-ion disposal.
WARNING
If the battery pack cracks or breaks, with or without leaks,
do not recharge it and do not use. Discard it and replace
with a new battery pack. DO NOT TRY TO REPAIR IT! To
prevent injury and risk of fire, explosion, or electric shock,
and to avoid damage to the environment:
• Cover the terminals of the battery with heavy-duty
adhesive tape.
• DO NOT try to remove or destroy any of the battery
pack components.
• DO NOT try to open the battery pack.
• If a leak develops, the released electrolytes are
corrosive and toxic. DO NOT get the solution in the
eyes or on skin, and do not swallow it.
• DO NOT put these batteries in your regular household
trash.
• DO NOT incinerate.
• DO NOT put them where they will become part of any
waste landfill or municipal solid waste stream.
• Take them to a certified recycling or disposal center.
6 PROPOSITION 65
WARNING
This product contains a chemical known to the state of
California to cause cancer, birth defects or other
reproductive harm. Some dust created by power sanding,
sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these chemicals
are:
• Lead from lead-based paints;
• Crystalline silica from bricks and cement and other
masonry products;
• Arsenic and chromium from chemically treated lumber.
Your risk of exposure to these chemicals varies depending
on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area,
and work with approved safety equipment, such as dust
masks that are specially designed to filter out microscopic
particles.
Save these instructions.
7 INSTALLATION
WARNING
Do not change or make accessories that are not
recommended by the manufacturer.
WARNING
Do not connect to power supply until you assemble all the
parts.
7.1 UNPACK THE MACHINE
WARNING
Make sure that you correctly assemble the machine before
use.
WARNING
• If the parts are damaged, do not use the machine.
• If you do not have all the parts, do not operate the
machine.
• If the parts are damaged or missing, speak to the service
center.
1. Open the package.
2. Read the documentation in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and package in compliance with local
regulations.
7.2 CAM LOCK ASSEMBLY
NOTE
Do not tighten the knob until the cam lock is in place.
1. Remove the knob (16) and spacer (31) from the cam lock
(32).
2. Insert the bolt (17) through the lower handle housing.
3. Slide the spacer (31) over the bolt (17).
4. Screw on the knob (16).
7
English EN
5. Fold the cam lock (32) to lock the handle into place.
7.3 UNFOLD THE MIDDLE HANDLE
1. Open the quick-release levers (12) on the two sides of the
middle handle (15).
2. Unfold the middle handle (15) until they come to a stop.
3. Close the quick-release levers (12).
4. Tighten the knobs (16) to hold the middle handle (15) in
position.
7.4 INSTALL THE UPPER HANDLE
1. Align the holes in the middle handle (15) and the upper
handle (14).
2. Put the bolts (17) through the holes.
3. Tighten the handle knobs (16) onto the bolts (17).
4. Do the same operation on the other side.
7.5 INSTALL THE CHUTE-ROTATION
BOX
1. Align the holes in the panel of the chute-rotation box (23)
and the switch box (24).
2. Put the chute-rotation box screws (18) through the holes.
3. Tighten the chute-rotation box screw nuts (19) with a
wrench (not included).
7.6 INSTALL THE CHUTE
DEFLECTOR
1. Align the grooves (26) of the discharge chute with the
slot (25) on the chute housing.
2. Push the discharge chute (7) into position.
3. Tighten the discharge chute screws (18) with a Phillips
head screw driver to lock the discharge chute.
7.7 INSTALL THE BATTERY PACK
8
English
EN
18
23
24
19
WARNING
• If the battery pack or charger is damaged, replace the
battery pack or the charger.
• Stop the machine and wait until the engine stops before
you install or remove the battery pack.
• Read, know, and follow the instructions in the battery
and charger manual.
NOTE
This machine has the dual-pack switch function that lets the
other battery pack continue to operate when the first one is
out of battery after 2-3 seconds. The machine can be
increased the double working time by the function.
1. Open the battery door (5).
2. Align the ribs on the battery pack (20) with the grooves in
the battery compartment.
3. Push the battery pack (20) into the battery compartment
until the battery pack (20) locks into place.
4. When you hear a click, the battery pack (20) is installed.
5. Close the battery door (5).
7.8 REMOVE THE BATTERY PACK
1. Open the battery door (5).
2. Push and hold the battery release button (21).
3. Remove the battery pack (20) from the machine.
8 OPERATION
WARNING
Wear eye protection during operation.
8.1 COLD WEATHER OPERATION
The safe battery operation temperature ranges from 1°F
(-17°C) to 113°F (45°C).
WARNING
Do not store or charge battery outside.
Battery must be charged and stored indoors prior to use of the
machine.
If the machine does not start：• remove the battery pack from the machine,
• charge the battery pack to 15 minutes in warm area, or
when the charging light turns green.
• Install the battery pack back in the unit.
8.2 BLUE LED LIGHT
33
1. LED light flashes blue if the battery voltage is low. Place
the battery in a room temperature area and charge until
the green charger light is flashing green.
2. Blue LED light (33) is always on if the battery
temperature is low. Bring the Battery and Charger in to a
warm area. Place the Battery in the charger and allow for
the battery to reach room temperature or when the light
on the charger is flashing Green. Once charger is flashing
green, take the battery and place it in the unit to begin
work.
8.3 START THE MACHINE
1. While holding the safety switch button (3), pull the bail
lever (2) to start the machine.
2. At the same time, the LED lights (8) can be turned on.
WARNING
Keep bystanders a safe distance from the machine.
9
English EN
2
3
8
WARNING
Examine the work area. Remove all stones, sticks, wire,
bones, and other debris that can ricochet because of the
rotating impeller.
8.4 STOP THE MACHINE
1. Release the bail lever (2) to stop the machine.
2. At the same time, the LED lights (8) can be turned off.
WARNING
Wait until the impeller fully stops before you start the
machine again. Do not quickly turn the machine off and on.
8.5 ADJUST THE DISCHARGE CHUTE
7
4
You can adjust the discharge chute 180° to change the snow
direction.
1. Push the chute-rotation handle (4) forward to move the
discharge chute (7) to the left.
2. Push the chute-rotation handle (4) rearward to move the
discharge chute (7) to the right.
8.6 ADJUST THE CHUTE DEFLECTOR
You can adjust the chute deflector up and down to change the
throwing distance of the snow.
WARNING
Release the bail switch before you adjust the chute
deflector.
WARNING
Do not push the deflector so far forward that a gap shows
between the deflector and the chute.
1. Push and hold the trigger (22) on the chute deflector (6).
2. Move the chute deflector (6) up to increase the snow
distance.
3. Move the chute deflector (6) down to decrease the snow
distance.
8.7 OPERATION TIPS
• If it is possible, clear the snow with the direction of the
wind.
• In strong winds, lower the chute deflector to direct the
snow to the ground.
• When you complete the work, let the machine operate for
a while to prevent ice formation in the discharge chute.
• If the snow is deeper than 8", decrease the speed and let
the machine work at its own rhythm.
• Do not use the scraper to remove compact snow and ice.
9 MAINTENANCE
WARNING
Remove the battery pack from the machine before
maintenance.
CAUTION
Use only approved replacement parts.
10
English
EN
CAUTION
Do not let brake fluids, gasoline, petroleum-based materials
touch the plastic parts. Chemicals can cause damage to the
plastic, and make the plastic unserviceable.
CAUTION
Do not use strong solvents or detergents on the plastic
housing or components.
9.1 GENERAL MAINTENANCE
• Before each use, examine the machine for damaged,
missing, or loose parts such as screws, nuts, bolts and
caps.
• Tighten correctly all the fasteners and caps.
• Clean the remaining snow on the machine with a brush.
9.2 REPLACE THE SCRAPER
WARNING
Use only approved replacement scrapers.
WARNING
Wear heavy gloves around the blade when you touch the
blade.
WARNING
The scraper is located at the bottom of the impeller housing.
Ensure that the battery is not installed in the tool.
1. Turn the machine to its side.
2. Remove the 5 bolts (17) below the deck that attach the
scraper (9) to the machine.
3. Remove the worn scraper (9) from the machine.
4. Install the new scraper (9).
5. Install and tighten the bolts (17) that you removed.
9.3 REPLACE THE BELT
WARNING
Make sure to turn off the bail lever and remove the battery
pack(s) before performing any maintenance task on your
snow thrower.
1. Remove the screws (18) on the side wear pad (27).
2. Turn the large pulley (29) counterclockwise while you
remove the remaining belt (28).
3. Turn the new belt (28) onto the pulleys (29).
4. Install and tighten the screws (18) that you removed.
9.4 REPLACE THE IMPELLER
WARNING
Make sure to turn off the bail lever and remove the battery
pack(s) before performing any maintenance task on your
snow thrower.
11
English EN
1. Remove the 4 sets of nuts and bolts on the middle steel
plate.
2. Remove the 4 sets of nuts and bolts on each side.
3. Remove the impellers (10).
4. Install the new impellers (10).
5. Tigthen the 8 sets of nuts and bolts that you removed.
9.5 REPLACE THE SKID PLATES
NOTE
The range of adjustable height for skid plates is 1.5mm,
when putting the bolts through the U-hole on the skid
plates.
1. Loosen the 2 sets of bolts (17), spacers (31) and nuts (19)
that attach the skid plates (30) to the snow thrower
housing.
2. Remove the skid plates (30).
3. Install the new skid plates (30).
4. Do the same operation on the other side.
9.6 STORE THE MACHINE
• Clean the machine before storage.
• Make sure the motor is not hot when you store the
machine.
• Make sure that the machine does not have loose or
damaged parts. If it is necessary, do these steps/
instructions:
• Replace the damaged parts.
• Tighten the bolts.
• Speak to a person at an approved service center.
• Store the machine in a dry area.
• Make sure that children cannot come near the machine.
10 TROUBLESHOOTING
Problem Possible cause Solution
The handle is not
in position.
The bolts are not
engaged correctly.
Adjust the height
of the handle and
make sure that the
knobs and bolts
are aligned cor-
rectly.
12
English
EN
Problem Possible cause Solution
The machine does
not start.
The battery is not
charged.
Charge the battery
by following the
procedures in the
battery and charg-
er manual.
The switch is de-
fective.
Have the switch
replaced by an au-
thorized service
center.
Battery is too cold. Remove battery
from snow throw-
er. Place battery on
charger and allow
to charge for 10
minutes or until
the changing light
turns green. Re-
move from charger
and install in snow
thrower for use.
Blue LED light is
Flashing - Battery
is in Low Voltage
Protection.
Bring the Battery
and Charger in to a
warm area. Place
the Battery in the
charger and allow
for the battery to
reach room tem-
perature or when
the light on the
charger is flashing
Green. Once
charger is flashing
green, take the bat-
tery and place it in
the unit to begin
work.
Blue LED light is
always on - Bat-
tery Temperature
is Low.
Bring the Battery
and Charger in to a
warm area. Place
the Battery in the
charger and allow
for the battery to
reach room tem-
perature or when
the light on the
charger is flashing
Green. Once
charger is flashing
green, take the bat-
tery and place it in
the unit to begin
work.
Battery may re-
quire service or re-
placement.
Call toll free help-
line, at
1-855-345-3934 or
replace battery.
Problem Possible cause Solution
The engine is on,
but the impeller
does not turn.
The belt is dam-
aged.
Replace the belt.
A thin layer of
snow stays behind.
The scraper is
damaged.
Replace the scra-
per.
* If you cannot find the solution to these problems, call
1-855-345-3934 .
11 TECHNICAL DATA
Voltage 60 V
No load speed 1800 RPM
Clearing width 22 in (56 cm)
Clearing depth 13 in (33 cm)
Impeller size 18 in (46 cm)
Weight (without battery
pack)
25.8 kg (56.9 lbs)
Battery LB604 and other BAC series
Charger CH60DP00 and other CAC
series
12 LIMITED WARRANTY
Greenworks hereby warranties this product, to the original
purchaser with proof of purchase, for a period of four (4)
years against defects in materials, parts or workmanship.
Greenworks, at its own discretion will repair or replace any
and all parts found to be defective, through normal use, free
of charge to the customer. This warranty is valid only for
units which have been used for personal use that have not
been hired or rented for industrial/commercial use, and that
have been maintained in accordance with the instructions in
the owners’ manual supplied with the product from new.
13
English EN
ITEMS NOT COVERED BY WARRANTY:
1. Any part that has become inoperative due to misuse,
commercial use, abuse, neglect, accident, improper
maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in
accordance with the owner's manual; or
3. Normal wear, except as noted below;
4. Routine maintenance items such as lubricants, blade
sharpening;
5. Normal deterioration of the exterior finish due to use or
exposure.
HELPLINE:
Warranty service is available by calling our toll-free helpline,
at 1-855-345-3934 .
TRANSPORTATION CHARGES:
Transportation charges for the movement of any power
equipment unit or attachment are the responsibility of the
purchaser. It is the purchaser’s responsibility to pay
transportation charges for any part submitted for replacement
under this warranty unless such return is requested in writing
by Greenworks.
USA address: Canadian address:
Greenworks Tools
P.O. Box 1238
Mooresville, NC 28115
14
English
EN
Greenworks Tools Canada Inc.
P.O.Box 93095, Newmarket,
Ontario
L3Y 8K3
13 EXPLODED VIEW
15
English EN
No. Part No. Qty Description
1 R0201719-00 1 Impeller assembly
2 R0200650-00 1 Scraper Kit
3 R0200662-00 1 Wheel Assembly
4 R0200651-00 1 Chute Deflector Assembly
5 R0200652-00 1 Quick-Release Lever Assembly
6 R0200653-00 1 Knob
7 R0201802-00 1 PCB board
8 R0200655-00 1 Skid plates
9 1 Belt
R0200288-00
1 DESCRIPTION
1.1 BUT
Cette machine est utilisée pour enlever et déblayer la neige
des trottoirs, jardins, allées et autres surfaces au niveau du
sol.
1.2 APERÇU
1Guidon
2Levier de verrouillage
3Bouton de sécurité de l’interrupteur
4Tige de commande de la goulotte
5Trappe de la batterie
6Déflecteur de la goulotte
7Goulotte d'éjection
8Lumière DEL
9Grattoir
10 Turbine
11 Roue
12 Levier à dégagement rapide
13 Poignée inférieure
14 Partie supérieure du guidon
15 Poignée du milieu
16 Bouton
17 Boulon
18 Vis
19 Écrou
20 Bloc-batterie
21 Bouton d’éjection de la batterie
22 Gâchette
23 Boîte de rotation de la chute
24 Boîtier de commutateur
25 Fente
26 Rainure
27 Usure de plaquette de frein
28 Courroie
29 Poulie
30 Disques de protection
31 Entretoise
32 Dispositif de blocage
33 Voyant DEL bleu
2 AVERTISSEMENTS
GÉNÉRAUX DE SÉCURITÉ
DES OUTILS ÉLECTRIQUES
AVERTISSEMENT
Lisez tous les avertissements de sécurité et toutes les
instructions. Le non-respect de ces avertissements et de ces
instructions peut entraîner un choc électrique, un incendie
et/ou des blessures graves.
Conservez tous les avertissements et instructions pour
référence ultérieure.
Le terme « outil électrique » dans les avertissements fait
référence à votre outil électrique (sans fil) fonctionnant sur
batterie.
2.1 FORMATION
• Ne laissez pas un enfant de moins de 14 ans utiliser cet
outil. Les enfants de 14 ans ou plus doivent lire et
comprendre les instructions d'utilisation et les règles de
sécurité contenues dans ce manuel et doivent être formés
et supervisés par un parent.
• Lisez attentivement le mode d’emploi et le manuel
d’utilisation. Familiarisez-vous parfaitement avec les
commandes et l’utilisation correcte de l’outil électrique.
Apprenez comment arrêter l'appareil et désengager
rapidement les commandes.
• Ne laissez jamais les enfants utiliser l’outil électrique.
N’autorisez jamais les adultes à utiliser l’outil électrique
sans instruction appropriée.
• Garder la zone d'opération à l'écart de toute personne, en
particulier les jeunes enfants et les animaux domestiques.
• Faites preuve de prudence pour éviter le glissement ou la
chute, surtout en opération en marche arrière.
• N’utilisez pas sur des surfaces caillouteuses.
• Habillez-vous correctement – Ne portez pas de vêtements
amples ou de bijoux. Ils pourraient se coincer dans les
pièces en mouvement.
• Portez des bottes adéquates lorsque vous utilisez la
déneigeuse.
• L’utilisation de la souffleuse à neige soutenue dans les
mains est dangereuse, sauf lorsqu'utilisée en conformité
avec les instructions spéciales pour cette utilisation
fournies dans le manuel de l’utilisateur.
17
Français
FR
Table of contents
Languages:
Other GreenWorks Pro Snow Blower manuals
GreenWorks Pro
GreenWorks Pro SSB403 User manual
GreenWorks Pro
GreenWorks Pro SN60L611 User manual
GreenWorks Pro
GreenWorks Pro SN60L02 User manual
GreenWorks Pro
GreenWorks Pro SNC403 User manual
GreenWorks Pro
GreenWorks Pro SNB403 User manual
GreenWorks Pro
GreenWorks Pro SN60L00 User manual
GreenWorks Pro
GreenWorks Pro GLSS80000 User manual
GreenWorks Pro
GreenWorks Pro SNC407 User manual
GreenWorks Pro
GreenWorks Pro 060-0799-6 User manual
GreenWorks Pro
GreenWorks Pro 2600402 User manual
GreenWorks Pro
GreenWorks Pro 2608402CO User manual
GreenWorks Pro
GreenWorks Pro SN60L522 User manual
GreenWorks Pro
GreenWorks Pro SNC406 User manual
GreenWorks Pro
GreenWorks Pro SN60L02 User manual
GreenWorks Pro
GreenWorks Pro 2601302 User manual
GreenWorks Pro
GreenWorks Pro SNB403 User manual
GreenWorks Pro
GreenWorks Pro SS60L00 User manual
GreenWorks Pro
GreenWorks Pro SN80L620 User manual
