Grizzly H6239 User manual

Introduction
The Model H6239 10 Ton Log Splitter (Figure 1)
features 10 tons of pressure for splitting firewood,
a 175⁄8" log capacity, an 81⁄4" ram stroke, and two
built-in mini wheels for easy mobility.
Inventory
A. Log Splitter ................................................ 1
B. Handles ...................................................... 2
Figure 1. Model H6239 handles installed.
This log splitter is only intended to be used
to split logs! Serious injury may occur if this
log splitter is used as a hydraulic press.
The Model H6239 is a
heavy machine (106 lbs.
shipping weight). DO
NOT over-exert yourself
while unpacking or mov-
ing your machine—get
assistance.
Wear ANSI approved safety glasses and
gloves at all times.
Figure 2. Model H6239 identification.
Advance
Pump
Handle
Splitting
Pump
Handle
Wedge
Release
Knob
Cradle
Piston
Rod
Keep hands and other body parts away
from wedge and piston rod when H6239 is
in operation to prevent serious injury. Keep
area around log splitter clear of bystanders
to prevent injury from ejected wood pieces.
Assembly
Insert a handle into each socket (Figure 1).
Operation
1. Cut the logs you want to split to 175⁄8" or less
to fit into the splitter.
2. Turn the release knob (Figure 2) counter-
clockwise to retract the piston rod fully into
the cylinder, then turn the knob clockwise.
10 TON LOG SPLITTER
MODEL H6239
INSTRUCTION SHEET
Sockets

Maintenance
Wipe down the log splitter to remove tree sap or
dirt. Occasionally you may need to add hydraulic
oil to maximize performance.
To add oil:
1. Fully extend the piston rod.
2. Remove the oil seal (Figure 3).
Figure 3. Oil Seal.
3. Turn the release knob counterclockwise to
expel air out of the oil seal hole.
4. Add hydraulic oil until the cylinder is 3⁄4 full.
5. Replace the oil seal.
If you need additional help with this procedure,
call our service department at: [phone].
3. Place a log on the cradle between the wedge
and piston rod.
4. Use the advance pump handle (Figure 1) to
quickly move the piston rod until it is close to
the log. Then use the splitting pump handle
(Figure 1) to split the log.
5. Turn the release knob counterclockwise to
return the piston rod to the cylinder, turn the
knob clockwise to start over, then remove the
split pieces.
Note—Cut your logs to the same length to
reduce log splitting time.
Storage
Store the log splitter in a dry location with the
release knob open, to relieve hydraulic pressure.
Oil Seal


























H6239 Parts Breakdown and List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PH6239001 FRAME 9 PH6239009 AXLE SLEEVE
2 PH6239002 RAM BRACKET 10 PH6239010 COTTER PIN
3 PH6239003 PIN SLEEVE 11 PH6239011 WHEEL
4 PH6239004 PIN 12 PB32M HEX BOLT M10-1.5 X 25
5 PH6239005 U-CLAMP 13 PW04M FLAT WASHER 10MM
6 PH6239006 EXTENSION SPRING 14 PLW06M LOCK WASHER 10MM
7 PH6239007 RAM 15 PN02M HEX NUT M10-1.5
8 PH6239008 AXLE 16 PH6239016 ADVANCE�PUMP�HANDLE
17 PH6239017 OIL SEAL
18 PH6239018 SPLITTING�PUMP�HANDLE
COPYRIGHT © FEBRUARY, 2005 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL6998 PRINTED IN CHINA