Grizzly H8100 User manual
MODEL H8100
8 TON LOG SPLITTER
INSTRUCTION SHEET
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
EYE INJURY HAZARD!
Always wear ANSI approved
safety glasses when using
this log splitter!
Inventory & Identification: (Figure 1)
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
Assembly
Note: Refer to the Parts Breakdown for
additional assembly details.
1.
2.
3.
This log splitter is only intended to be used
to split logs! Serious injury may occur if this
log splitter is used for any other purpose.
If you need help with your new log splitter, call our
Tech Support at: (570) 546-9663.
Introduction
Figure 1.
Operation
1.
2.
Note: Make sure the wedge release pins are
firmly seated in the post holes before continu-
ing.
4.
5.
6.
7.
8.
Storage
Maintenance
To add oil to the hydraulic pump:
Note: Refer to the Parts Breakdown to iden-
tify parts named below.
1.
2.
3.
4.
5.
1. Read and understand this entire instruc-
tion sheet before using this log splitter.
2. Always wear ANSI approved safety
glasses when using this log splitter to
avoid damage to eyes from flying wood
pieces.
3. Never place your hands or other body
parts on or near the log, wedge, hydrau-
lic ram, or splitter workbench when
splitting the log.
4. Do not use this log splitter for any other
purpose other than splitting logs. Do
not use this log splitter beyond its 8 ton
capacity.
5. Never leave the log under pressure.
6. Keep the area around log splitter clear
of bystanders to prevent injury from
ejected wood pieces.
7. Always clear away wood pieces from the
log splitter and the area around it before
starting on another log.
If you need help with this procedure, call our Tech
Support at: (570) 546-9663.
1
2
3
4
20V2
21
38
33 34 35 36
39
5V2
10
7
8V2
9
10
11
12
13
14
15
18 17
22
23
25
24
29
31
28
26
30
16V2
16V2
37
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PH8100001 THREADED PIN HOUSING 20V2 PH8100020V2 HYD. FOOT PEDAL V2.05.09
2 PH8100002 WEDGE RELEASE PIN 21 PB83M HEX BOLT M6-1 X 16
3 PH8100003 RING 22 PH8100022 SPECIFICATION LABEL
4 PH8100004 COMPRESSION SPRING 23 PH8100023 GENERAL WARNINGS LABEL
5V2 PH8100005V2 SPLITTER BODY V2.05.09 24 PH8100024 ENTANGLEMENT LABEL
6 PH8100006 WEDGE ASSEMBLY 25 PH8100025 EYE INJURY LABEL
7 PH8100007 SPLITTER WORKBENCH 26 PH8100026 CRUSHING HAZARD LABEL
8V2 PH8100008V2 HYDRAULIC PUMP V2.05.09 28 PH8100028 HANDLE
9 PH8100009 RETURN SPRING 29 PLW06M LOCK WASHER 10MM
10 PCAP14M CAP SCREW M8-1.25 X 20 30 PN02M HEX NUT M10-1.5
11 PH8100011 WHEEL 31 PH8100031 HANDLE SLEEVE
12 PH8100012 BUSHING 33 PH8100033 TORSION SPRING SLEEVE
13 PW10M FLAT WASHER 14MM 34 PH8100034 TORSION SPRING
14 PR02M EXT RETAINING RING 14MM 35 PH8100035 EXTENSION ROD
15 PB32M HEX BOLT M10-1.5 X 25 36 PH8100036 THIN HEX NUT M16
16V2 PH8100016V2 STABILIZER BAR V2.05.09 37 PH8100037 RELEASE PEDAL
17 PLW06M LOCK WASHER 10MM 38 PN01M HEX NUT M6-1
18 PN02M HEX NUT M10-1.5 39 PSS04M SET SCREW M6-1 X 12
Parts Breakdown ~ Version 2.05.09
NOTICE
Safety labels warn about machine
hazards and ways to prevent injury.
The owner of this machine MUST
maintain the original location and
readability of the labels on the
machine. If any label is removed
or becomes unreadable, REPLACE
that label before using the machine
again. Contact Grizzly at (800) 523-
4777 or www.grizzly.com to order
new labels.
Buy Direct and Save with Grizzly® –Trusted, Proven and a Great Value!
~Since 1983~
ORDER
24 HOURS A DAY!
1-800-523-4777
Visit Our Website Today For
Current Specials!
Other Grizzly Log Splitter manuals
