Grizzly G0623X User manual

G0623X ONLY
MODEL G0623X/G0623X3
10" SLIDING TABLE SAW
OWNER'S MANUAL
(For models manufactured since 05/22)
COPYRIGHT © NOVEMBER, 2007 BY GRIZZLY INDUSTRIAL, INC., REVISED JULY, 2022 (KS)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR9147 PRINTED IN TAIWAN V6.07. 2 2
***Keep for Future Reference***

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.

Table of Contents
INTRODUCTION............................................... 2
Contact Info.................................................... 2
Manual Accuracy ........................................... 2
Identification ................................................... 3
Machine Data Sheets .................................... 4
SECTION 1: SAFETY....................................... 8
Safety Instructions for Machinery .................. 8
Additional Safety for Sliding Table Saws ..... 10
Preventing Kickback .................................... 11
Protecting Yourself From Kickback.............. 11
Glossary of Terms ....................................... 12
SECTION 2: POWER SUPPLY ...................... 13
G0623X3 440V Voltage Conversion ............ 16
SECTION 3: SETUP ....................................... 17
Needed for Setup ......................................... 17
Unpacking .................................................... 17
Inventory ...................................................... 18
Hardware Recognition Chart ....................... 20
Cleanup ........................................................ 21
Site Considerations ...................................... 22
Lifting & Placing ........................................... 23
Assembly ..................................................... 24
Power Connection........................................ 32
Test Run ...................................................... 33
SECTION 4: OPERATIONS ........................... 35
Operation Overview ..................................... 35
Workpiece Inspection................................... 36
Non-Through & Through Cuts ..................... 36
Blade Guard & Splitter/Riving Knife ............. 37
Safety Tips ................................................... 40
Blade Requirements .................................... 40
Blade Selection ............................................ 40
Changing Main Blade .................................. 42
Changing/Adjusting Scoring Blade .............. 43
Rip Cutting ................................................... 44
Crosscutting ................................................. 46
Miter Cutting................................................. 48
Dado Cutting ................................................ 49
Rabbet Cutting ............................................. 51
Resawing ..................................................... 53
SECTION 5: SHOP-MADE SAFETY
ACCESSORIES .............................................. 55
Featherboards .............................................. 55
Push Sticks .................................................. 58
Push Blocks ................................................. 59
Zero-Clearance Insert .................................. 60
Outfeed Table .............................................. 61
SECTION 6: ACCESSORIES ......................... 62
SECTION 7: MAINTENANCE......................... 66
Schedule ...................................................... 66
Cleaning ....................................................... 66
Unpainted Cast Iron ..................................... 66
Lubrication ................................................... 67
SECTION 8: SERVICE ................................... 68
Troubleshooting ........................................... 68
Belt Replacement......................................... 70
Blade Tilt Calibration .................................... 71
Sliding Table Parallel Adjustment ................ 72
Sliding Table Adjustment ............................. 73
Squaring Crosscut Fence to Blade .............. 74
Splitter/Riving Knife Mounting Block ............ 75
SECTION 9: WIRING...................................... 76
Wiring Safety Instructions ............................ 76
G0623X Wiring Diagram .............................. 77
G0623X3 7.5 HP 220V Wiring Diagram ...... 78
G0623X3 7.5 HP 440V Wiring Diagram ...... 79
SECTION 10: PARTS..................................... 80
Cabinet ......................................................... 80
Main Trunnion .............................................. 81
Main Motor ................................................... 82
Sliding Table ................................................ 84
Tables .......................................................... 86
Rip Fence..................................................... 87
Handwheels ................................................. 88
Scoring Trunnion.......................................... 89
Crosscut Table ............................................. 90
Swing Arm.................................................... 91
Miter Gauge ................................................. 92
Crosscut Fence ............................................ 93
Labels & Cosmetics ..................................... 94
WARRANTY.................................................... 97

-2- Model G0623X/G0623X3 (Mfd. Since 05/22)
INTRODUCTION
We stand behind our machines! If you have ques-
tions or need help, contact us with the information
below. Before contacting, make sure you get the
serial number
and manufacture date
from the
machine ID label. This will help us help you faster.
Grizzly Technical Support
1815 W. Battlefield
Springfield, MO 65807
Phone: [phone]
Email: [email protected]
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: [email protected]
Contact Info
We are proud to provide a high-quality owner’s
manual with your new machine!
We
made every effort to be exact with the
instruc-
tions, specifications, drawings, and photographs
in this manual. Sometimes we make mistakes, but
our policy of continuous improvement also means
that
sometimes the machine
you receive is
slightly different than shown in the manual
.
If you find this to be the case, and the difference
between the manual and machine leaves you
confused or unsure about something
,
check our
website for an updated version. W
e post
current
manuals and
manual updates for free
on our web-
site at
www.grizzly.com.
Alternatively, you can call our Technical Support
for help. Before calling, make sure you write
down the
manufacture date and
serial number
from the machine ID label (see below). This
information is required for us to provide proper
tech support, and it helps us determine if updated
documentation is available for your machine.
Manufacture Date
Serial Number
Manual Accuracy
No list of safety guidelines can be com-
plete. Every shop environment is different.
Always consider safety first, as it applies
to your individual working conditions. Use
this and other machinery with caution and
respect. Failure to do so could result in
serious personal injury, damage to equip-
ment, or poor work results.
Like all machinery there is potential danger
when operating this machine. Accidents
are frequently caused by lack of familiarity
or failure to pay attention. Use this machine
with respect and caution to decrease the
risk of operator injury. If normal safety pre-
cautions are overlooked or ignored, seri-
ous personal injury may occur.

Model G0623X/G0623X3 (Mfd. Since 05/22) -3-
C
G
H
A. Crosscut Table: Provides a wide, stable
platform for supporting full-size panels during
crosscutting operations.
B. Flip Stops: Used for quick measurements
for crosscutting.
C. Crosscut Fence: Used during crosscutting
operations. Features a scale and multiple
flip-style stop blocks for precise, repeatable
crosscutting operations.
D. Sliding Table: Glides workpiece through
blade with effortless precision and ease.
E. Blade Guard: Fully-adjustable blade guard
maintains maximum protection around saw
blade, and a 2½" dust port effectively extracts
dust from cutting operation.
F. Rip Fence: Fully adjustable with micro-
adjustment knob for precision adjustments.
Fence face can be positioned for standard
cutting operations, or in lower position for
blade guard clearance during narrow ripping
operations.
G. Magnetic ON/OFF Switch: Green start but-
ton turns motor ON. Red Emergency Stop
button turns motor OFF; for safety purposes,
this button will remain depressed and prevent
restarting until reset. Reset by rotating clock-
wise until it pops out.
H. Blade Angle Handwheel: Adjusts angle of
saw blades.
I. Blade Elevation Handwheel: Adjusts height
of main saw blade.
A
D
E
BF
I
Identification

-4- Model G0623X/G0623X3 (Mfd. Since 05/22)
Model Number G0623X G0623X3
Product Dimensions
Weight 533 lbs
Width (side-to-side)/Depth
(front-to-back)/Height 76 x 125 x 46 in.
Foot Print (Width/Depth) 25-1/2 x 28 in. 25-1/2 x 28 in.
Shipping Dimensions
Carton 1
Type Wood Crate
Content Machine
Weight 570 lbs. 556 lbs.
Width (side-to-side)/Depth
(front-to-back)/Height 45 x 42 x 42 in.
Carton 2
Type Cardboard
Content Sliding Table & Fence
Weight 118 lbs.
Width (side-to-side)/Depth
(front-to-back)/Height 66 x 18 x 9 in.
Electrical
Power Requirement 230V, Single-Phase, 60 Hz 220V or 440V, 3-Phase, 60 Hz
Prewired Voltage 230V 220V
Full-Load Current Rating 19A 18A @ 220V, 9A at 440V
Minimum Circuit Size 30A 30A @ 220V, 15A @440V
Switch Magnetic with Thermal Overload Protection
Power Cord "S"-Type, 3-Wire, 12 AWG, 300 VAC Recommend "S"-Type, 4-Wire, 10 AWG, 300
VAC for 220V; Permanent Connection for 440V
Plug Included Yes No
Plug/Outlet Type L6-30 Recommend L15-30 for 220V; Permanent
Connection for 440V
Voltage Conversion Kit Not Applicable Requires Part# G440VG0623X3
Recommended Phase
Converter Not Applicable G5845
Main Motor
Type TEFC Capacitor-Start Induction TEFC Induction
Horsepower 5 HP 7.5 HP
Voltage 230V 220V/440V
Prewired Not Applicable 220V
Phase Single-Phase 3-Phase
Amps 19A 18A @ 220V, 9A @ 440V
Speed 3450 RPM
Centrifugal Switch/Contacts External
Power Transfer V-Belt Drive
Bearings Sealed and Lubricated
MODEL G0623X & G0623X3
10" SLIDING TABLE SAW SPECIFICATIONS

Model G0623X/G0623X3 (Mfd. Since 05/22) -5-
Model Number G0623X G0623X3
Operation Information
Main Blade Size 10 in.
Main Arbor Size 5/8 in.
Scoring Blade Size 3-1/8 in.
Scoring Blade Arbor Size 22mm
Maximum Width of Dado 13/16 in.
Main Blade Tilt 0 - 45 deg
Main Blade Speed 4000 RPM
Scoring Blade Tilt 0 - 45 deg
Scoring Blade Speed 8000 RPM
Cutting Capacities
Max Depth of Cut At 90 Deg 3-1/8 in.
Max Depth of Cut At 45 Deg 2-1/4 in.
Table With Rip Fence Max Cut
Width 33 in.
Sliding Table With Cross Fence
Max Cut Width 78-1/2 in.
Sliding Table With Cross Fence
Max Cut Length 63 in.
Miter Fence Cut Width At 45 Deg 63 in.
Table Information
Floor To Table Height 33-5/8 in.
Table Size Length 27 in.
Table Size Width 14-3/8 in.
Table Size Thickness 2 in.
Table Size With Ext Wings Length 47 in.
Table Size With Ext Wings Width 40 in.
Table Size With Ext Wings
Thickness 2 in.
Sliding Table Length 63 in.
Sliding Table Width 12-1/4 in.
Sliding Table Thickness 3-1/2 in.
Sliding Table T-Slot Top Width 5/8 in.
Sliding Table T-Slot Height 1/2 in.
Sliding Table T-Slot Bottom Width 1-1/4 in.
Fence Information
Fence Type Single Lever Locking, Extruded Aluminum
Fence Size Length 33-1/2 in.
Fence Size Width 2 in.
Fence Size Height 4-1/4 in.
Fence Stops 2

-6- Model G0623X/G0623X3 (Mfd. Since 05/22)
Model Number G0623X G0623X3
Construction Materials
Table Precision-Ground Cast Iron
Sliding Table Aluminum
Cabinet Steel
Rip Fence Rails Extruded Aluminum
Guard Plastic
Spindle Bearing Type Sealed & Permanently Lubricated
Cabinet Paint Type/Finish Powder Coated
Other Related Information
No of Dust Ports 2
Dust Port Size 4, 2-1/2 in.
Other Specifications
Country of Origin Taiwan
Warranty 1 Year
Approximate Setup Time 1-1/2 Hours
Serial Number Location ID Label
ISO 9001 Factory Yes

Model G0623X/G0623X3 (Mfd. Since 05/22) -7-
MODEL G0623X 10" SLIDING TABLE SAW
Customer Service #: [phone] • To Order Call: [phone] • Fax #: [phone]
SLIDING TABLE
SAW CAPACITIES
Ripping Width
Miter Cut 90º
(push cut)
Miter Cut 45º
Miter Cut 45º
(push cut)
Cross Cut
(fence not extended)
Miter Cut 45º
(push cut, fence not extended)
Miter Cut 45º
(fence not extended)
Cross Cut
33"
78-1/2"
63"
111-1/2"
50"
63"
48"
48-3/4"
63"
78-1/2"
44-1/2"
31-1/2"
48-3/4"
44-1/2"
31-1/2"
78-1/2"
63"
48"
78-1/2"
37"
MODEL G0623X/G0623X3 10" SLIDING TABLE SAW
model g0623X3 10" SlIdINg TABle SAW
Customer Service #: [phone] • To Order Call: [phone] • Fax #: [phone]
SlIdINgTABle
SAW CAPACITIeS
Ripping Width
Miter Cut 90º
(push cut)
Miter Cut 45º
Miter Cut 45º
(push cut)
Cross Cut
(fence not extended)
Miter Cut 45º
(push cut, fence not extended)
Miter Cut 45º
(fence not extended)
Cross Cut
33"
78-1/2"
63"
50"
63"
48"
48-3/4"
63"
78-3/4"
44-1/2"
31-1/2"
48-3/4"
44-1/2"
31-1/2"
78-3/4"
63"
48"
78-3/4"
37"

-8- Model G0623X/G0623X3 (Mfd. Since 05/22)
ELECTRICAL EQUIPMENT INJURY RISKS.
You can be shocked, burned, or killed by touching
live electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
DISCONNECT POWER FIRST.
Always discon-
nect machine from power supply BEFORE mak-
ing adjustments, changing tooling, or servicing
machine. This prevents an injury risk from unin-
tended startup or contact with live electrical com-
ponents.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are NOT approved safety glasses.
OWNER’S MANUAL. Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY. Untrained oper-
ators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, dis-
connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make your workshop kid proof!
DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machin-
ery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.
For Your Own Safety, Read Instruction
Manual Before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Alerts the user to useful information about proper operation of the
machine to avoid machine damage.
NOTICE
Safety Instructions for Machinery
SECTION 1: SAFETY

Model G0623X/G0623X3 (Mfd. Since 05/22) -9-
WEARING PROPER APPAREL. Do not wear
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to reduce
risk of slipping and losing control or accidentally
contacting cutting tool or moving parts.
HAZARDOUS DUST. Dust created by machinery
operations may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece mate-
rial. Always wear a NIOSH-approved respirator to
reduce your risk.
HEARING PROTECTION. Always wear hear-
ing protection when operating or observing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
REMOVE ADJUSTING TOOLS. Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!
USE CORRECT TOOL FOR THE JOB. Only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. Never make unapproved modifica-
tions—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!
AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
Do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.
GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly BEFORE
operating machine.
FORCING MACHINERY. Do not force machine.
It will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement dur-
ing operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for rec-
ommended accessories. Using improper acces-
sories will increase the risk of serious injury.
UNATTENDED OPERATION. To reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
DAMAGED PARTS. Regularly inspect machine
for damaged, loose, or mis-adjusted parts—or
any condition that could affect safe operation.
Immediately repair/replace BEFORE operating
machine. For your own safety, DO NOT operate
machine with damaged parts!
MAINTAIN POWER CORDS. When disconnect-
ing cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the cord
may damage the wires inside. Do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intend-
ed operation, stop using the machine! Contact our
Technical Support at [phone].

-10- Model G0623X/G0623X3 (Mfd. Since 05/22)
Additional Safety for Sliding Table Saws
Serious injury or death can occur from getting cut or having body parts, such as fingers,
amputated by rotating saw blade. Workpieces thrown by kickback can strike operators or
bystanders with deadly force. Flying particles from cutting operations or broken blades can
cause eye injuries or blindness. To minimize risk of getting hurt or killed, anyone operating
machine MUST completely heed hazards and warnings below.
HAND & BODY POSITIONING. Keep hands
away from saw blade and out of blade path dur-
ing operation, so they cannot slip accidentally into
blade. Stand to side of blade path. Never reach
around, behind, or over blade. Only operate at
front of machine.
BLADE GUARD. Use blade guard for all cuts
that allow it to be used safely. Make sure blade
guard is installed and adjusted correctly. Promptly
repair or replace if damaged. Re-install blade
guard immediately after operations that require its
removal.
RIVING KNIFE. Use riving knife for all cuts. Make
sure riving knife is aligned and positioned cor-
rectly. Promptly repair or replace it if damaged.
KICKBACK. Kickback occurs when saw blade
ejects workpiece back toward operator. Know how
to reduce risk of kickback. Learn how to protect
yourself if it does occur.
WORKPIECE CONTROL. Feeding workpiece
incorrectly increases risk of kickback. Make sure
workpiece is in stable position on tables and
supported by rip fence or crosscut fence during
cutting operation. Never start saw with workpiece
touching blade. Allow blade to reach full speed
before cutting. Only feed workpiece against direc-
tion of main blade rotation. Always use some type
of guide to feed workpiece in a straight line. Never
back workpiece out of cut or move it backwards
or sideways after starting a cut. Feed cuts all the
way through to completion. Never perform any
operation “freehand”. Turn OFF saw and wait
until blade is completely stopped before removing
workpiece.
FENCE ADJUSTMENTS. Make sure rip fence
remains properly adjusted and parallel with blade.
Never move fence while blade is rotating. Adjusting
fence during operation increases risk of crashing
fence and sending metal fragments flying with
deadly force at operator or bystanders. Only
adjust fence when blade is completely stopped
and saw is OFF. Always lock fence before using.
PUSH STICKS/BLOCKS. Use push sticks or
push blocks whenever possible to keep your
hands farther away from blade while cutting. In
event of an accident these devices will often take
damage that would have happened to hands/
fingers.
BLADE ADJUSTMENTS. Adjusting blade height
or tilt during operation increases risk of crash-
ing blade and sending metal fragments flying
with deadly force at operator or bystanders. Only
adjust blade height and tilt when blade is com-
pletely stopped and saw is OFF.
CHANGING BLADES. Always disconnect power
before changing blades. Changing blades while
saw is connected to power greatly increases
injury risk if saw is accidentally powered up.
DAMAGED SAW BLADES. Never use blades
that have been dropped or otherwise damaged.
CUTTING CORRECT MATERIAL. Never cut
materials not intended for this saw. Only cut natu-
ral and man-made wood products, laminate cov-
ered wood products, and some plastics. Cutting
metal, glass, stone, tile, etc. increases risk of
operator injury due to kickback or flying particles.

Model G0623X/G0623X3 (Mfd. Since 05/22) -11-
Below are ways to avoid the most common
causes of kickback:
• Only cut workpieces with at least one smooth
and straight edge. DO NOT cut excessively
warped, cupped or twisted wood. If the
workpiece warpage is questionable, always
choose another workpiece.
• Never attempt freehand cuts. If the workpiece
is not fed parallel with the blade, a kickback
will likely occur. Always use the rip fence or
crosscut fence to support the workpiece.
• Make sure the splitter/riving knife is aligned
with the blade. A misaligned splitter/riving
knife can cause the workpiece to catch or
bind, increasing the chance of kickback. If
you think that your splitter/riving knife is not
aligned with the blade, check it immediately!
• Ensure that your table slides parallel with the
blade; otherwise, the chances of kickback are
greatly increased. Take the time to check and
adjust the sliding table to be parallel with the
blade.
• Do not remove the splitter/riving knife. The
splitter/riving knife maintains the kerf in the
workpiece, reducing the chance of kickback.
• Keep the blade guard installed and working
correctly for all through cuts.
• Feed cuts through to completion. Anytime
you stop feeding a workpiece in the middle of
a cut, the chance of kickback is increased.
• Never move the workpiece backwards while
cutting or try to back it out of a cut while the
blade is moving. If you cannot complete a
cut for some reason, stop the saw motor and
allow the blade to completely stop moving
before backing the workpiece out. Promptly
fix the condition that prevented you from
completing the cut, before starting the saw
again.
Statistics show that most common acci-
dents among table saw users can be linked
to kickback. Kickback is typically defined
as the high-speed ejection of stock from the
table saw toward its operator. In addition to
the danger of the operator or others in the
area being struck by the flying stock, it is
often the case that the operator’s hands are
pulled into the blade during the kickback.
Even if you know how to prevent kickback, it
may still happen. Here are some tips to pro-
tect yourself if kickback DOES occur:
• Stand to the side of the blade during every
cut. If a kickback does occur, the thrown
workpiece usually travels directly in front of
the blade.
• Wear safety glasses or a face shield. In the
event of a kickback, your eyes and face are
the most vulnerable part of your body.
• Never, for any reason, place your hand
behind the blade. Should kickback occur,
your hand will be pulled into the blade, which
could cause amputation.
• Use a push stick to keep your hands farther
away from the moving blade. If a kickback
occurs, the push stick will most likely take
the damage that your hand would have
received.
• Use featherboards or anti-kickback devices
to assist with feeding and prevent or slow
down kickback.
Preventing Kickback Protecting Yourself
From Kickback

-12- Model G0623X/G0623X3 (Mfd. Since 05/22)
The following is a list of common definitions, terms and phrases used throughout this manual as they relate
to this table saw and woodworking in general. Become familiar with these terms for assembling, adjusting
or operating this machine.
Arbor: The metal shaft on which the blade is
mounted.
Bevel Edge Cut: A cut made along the edge of
a workpiece with the saw blade tilted between 0˚
and 45˚. Refer to Page 72 for more details.
Blade Guard Assembly: A safety device that
mounts over the saw blade to help prevent acci-
dental contact with the saw blade and to contain
flying chips and dust. Refer to Page 38 for more
details.
Crosscut: Cutting operation in which the miter
gauge is used to hold the workpiece while it is
cut across its shortest width. Refer to Page 47 for
more details.
Dado Blade: Blade or set of blades that are used
to cut grooves and rabbets.
Dado Cut: Cutting operation that uses a dado
blade to cut a flat bottomed groove into the face of
the workpiece. Refer to Page 50 for more details.
Featherboard: Safety device used to keep the
workpiece held firmly against the rip fence or table
surface. Refer to Page 56 for more details.
Kerf: The resulting cut or gap in the workpiece
after the saw blade passes through during a cut-
ting operation.
Kickback: An event in which the spinning blade
ejects the workpiece toward the front of the saw
at a high rate of speed.
Non-Through Cut: A cut in which the blade does
not cut through the top of the workpiece. Refer to
Page 37 for more details.
Parallel: Being an equal distance apart at every
point along two given lines or planes (i.e. the
rip fence face is parallel to the face of the saw
blade).
Perpendicular: Lines or planes that intersect and
form right angles (i.e. the blade is perpendicular to
the table surface).
Push Stick: Safety device used to push the
workpiece through a cutting operation. Used most
often when rip cutting thin workpieces. Refer to
Page 59 for more details.
Rabbet: Cutting operation that creates an
L-shaped channel along the edge of the workpiece.
Refer to Page 52 for more details.
Rip Cut: Cutting operation in which the rip fence
is used to cut across the widest width of the
workpiece. Refer to Page 45 for more details.
Splitter/Riving Knife: Curved metal plate locat-
ed behind the blade. Maintains kerf opening in
wood when performing a cutting operation. Acts
as a barrier behind blade to shield hands from
being pulled into the blade if a kickback occurs.
Refer to Page 40 for more details.
Straightedge: A tool used to check the flatness,
parallelism, or consistency of a surface(s).
Thin Kerf Blade: A blade with a kerf or thickness
that is thinner than a standard blade cannot be
used on this saw.
Through Cut: A cut in which the blade cuts com-
pletely through the workpiece (refer to Page 37).
Glossary of Terms

Model G0623X/G0623X3 (Mfd. Since 05/22) -13-
Availability
Before installing the machine, consider the avail-
ability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrician or
qualified service personnel in accordance with all
applicable codes and standards.
Electrocution, fire, shock,
or equipment damage
may occur if machine is
not properly grounded
and connected to power
supply.
Full-Load Current Rating
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid over-
loading the machine during operation and make
sure it is connected to a power supply circuit that
meets the specified circuit requirements.
For your own safety and protection of
property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.
Note: Circuit requirements in this manual apply to
a dedicated circuit—where only one machine will
be running on the circuit at a time. If machine will
be connected to a shared circuit where multiple
machines may be running at the same time, con-
sult an electrician or qualified service personnel to
ensure circuit is properly sized for safe operation.
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power sup-
ply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
Circuit Information
G0623X at 230V, 1-Ph......................... 19 Amps
G0623X3 at 220V, 3-Ph....................... 18 Amps
G0623X3 at 440V, 3-Ph......................... 9Amps
Grounding Requirements
This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is nec-
essary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.
Check with a qualified electrician or service per-
sonnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, discon-
nect it from power, and immediately replace it with
a new one.
SECTION 2: POWER SUPPLY

-14- Model G0623X/G0623X3 (Mfd. Since 05/22)
G0623X3 Circuit Requirements 220V
This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:
No adapter should be used with plug. If
plug does not fit available receptacle, or if
machine must be reconnected for use on a
different type of circuit, reconnection must
be performed by an electrician or qualified
service personnel, and it must comply with
all local codes and ordinances.
Figure 2. Typical L15-30 plug and receptacle.
Grounding Prong
is Hooked
Current Carrying Prongs
GROUNDED
L15-30 RECEPTACLE
L15-30
PLUG
G0623X Circuit Requirements
This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:
No adapter should be used with plug. If
plug does not fit available receptacle, or if
machine must be reconnected for use on a
different type of circuit, reconnection must
be performed by an electrician or qualified
service personnel, and it must comply with
all local codes and ordinances.
Figure 1. Typical L6-30 plug and receptacle.
Grounding Prong
is Hooked
Current Carrying Prongs
L6-30 GROUNDED
LOCKING
RECEPTACLE
L6-30
LOCKING
PLUG
This machine is equipped with a power cord that
has an equipment-grounding wire and a grounding
plug. Only insert plug into a matching receptacle
(outlet) that is properly installed and grounded in
accordance with all local codes and ordinances.
DO NOT modify the provided plug!
The power cord and plug used on this machine
must have an equipment-grounding wire and
grounding prong. The plug must only be inserted
into a matching receptacle (outlet) that is prop-
erly installed and grounded in accordance with all
local codes and ordinances (see figure below).
Nominal Voltage ......... 208V, 220V, 230V, 240V
Cycle ..........................................................60 Hz
Phase ........................................... Single-Phase
Circuit Rating...................................... 30 Amps
Plug/Receptacle .......................................L6-30
Nominal Voltage ......... 208V, 220V, 230V, 240V
Cycle ..........................................................60 Hz
Phase .................................................... 3-Phase
Power Supply Circuit ......................... 30 Amps
Plug/Receptacle ..................................... L15 - 30
Cord ........"S"-Type, 4-Wire, 10 AWG, 300 VAC

Model G0623X/G0623X3 (Mfd. Since 05/22) -15-
G0623X3 Circuit Requirements 440V
This machine can be converted to operate on a
power supply circuit that has a verified ground
and meets the requirements listed below. (Refer
to Voltage Conversion instructions for details.)
Extension Cords
We do not recommend using an extension cord
with this machine.
If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.
Extension cords cause voltage drop, which can
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Any extension cord used with this machine must
be in good condition and contain a ground wire
and matching plug/receptacle. Additionally, it must
meet the following size requirements:
G0623X .............. 3 Wire, 10 AWG, 50 ft. or less
G0623X3 (220V) 4 Wire, 10 AWG, 50 ft. or less
G0623X3 (440V) .......................N/A (Hardwired)
A permanently connected (hardwired) power sup-
ply is typically installed with wires running through
mounted and secured conduit. A disconnecting
means, such as a locking switch (see following
figure), must be provided to allow the machine
to be disconnected (isolated) from the power
supply when required. This installation must be
performed by an electrician in accordance with all
applicable electrical codes and ordinances.
Figure 3. Typical setup of a permanently
connected (hardwired) machine.
Power
Source
Locking
Disconnect Switch
Machine
Ground Ground
ConduitConduit
In the event of a malfunction or breakdown,
grounding provides a path of least resistance
for electrical current to reduce the risk of electric
shock. A permanently connected machine must
be connected to a grounded metal permanent wir-
ing system; or to a system having an equipment-
grounding conductor. All grounds must be verified
and rated for the electrical requirements of the
machine. Improper grounding can increase the
risk of electric shock!
Nominal Voltage ............................. 440V, 480V
Cycle ..........................................................60 Hz
Phase .................................................... 3-Phase
Power Supply Circuit ......................... 15 Amps
Connection Type ......... Permanent (Hardwire)

-16 - Model G0623X/G0623X3 (Mfd. Since 05/22)
The Model G0623X3 is prewired for 220V 3-phase
operation, but can be rewired for 440V operation.
To complete this conversion procedure, you must
buy a 440V magnetic switch and rewire the motor
for 440V operation. The 440V magnetic switch,
Part P0623X30346A, can be purchased from
Grizzly by calling 1-800-523-4777.
This rewiring job must be inspected by a quali-
fied electrician before the saw is connected to the
power source. Also, the junction box on the motor
can be accessed easier for rewiring if the blade is
moved to 0˚ (90˚ to table) before beginning.
To rewire the machine for 440V operation:
1. DISCONNECT MACHINE FROM POWER!
2. Remove cover of magnetic switch.
3. Disconnect all wires from incoming power
cords.
4. Remove magnetic switch and install new
magnetic switch in same manner as old
switch was installed. Refer to wiring diagram
on Page 80 if you need help remembering
where wires are attached.
5. Remove cabinet cover from back of machine.
6. Rewire motor to 440V as shown in diagram
on Page 80.
7. Replace junction box cover, cabinet door
cover, and magnetic switch cover.
G0623X3 440V
Voltage Conversion

Model G0623X/G0623X3 (Mfd. Since 05/22) -17-
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu-
al to become familiar with
the controls and opera-
tions before starting the
machine!
Wear safety glasses during
the entire setup process!
HEAVY LIFT!
Straining or crushing injury
may occur from improperly
lifting machine or some of
its parts. To reduce this risk,
get help from other people
and use a forklift (or other
lifting equipment) rated for
weight of this machine.
This machine was carefully packaged for safe
transport. When unpacking, separate all enclosed
items from packaging materials and inspect them
for shipping damage.
If items are damaged
,
please
call us immediately at [phone].
IMPORTANT:
Save all packaging materials until
you are completely satisfied with the machine and
have resolved any issues between Grizzly or the
shipping agent. You MUST have the original pack-
aging to file a freight claim. It is also extremely
helpful if you need to return your machine later.
Unpacking
The following are needed to complete the setup
process, but are not included with your machine.
Items Needed Qty
• Additional People ....................................... 2
• Safety Glasses (for each person) .............. 1
• Heavy Leather Gloves .........................1 Pair
• Forklift (Rated for at least 800 lbs.) ............ 1
• Lifting Straps .............................................. 2
• Cleaner/Degreaser (Page 22) .... As Needed
• Disposable Shop Rags ............... As Needed
• Disposable Gloves ..................... As Needed
• Main Saw Blade (Page 41) ........................ 1
• Prybar ......................................................... 1
• Straightedge 4' ........................................... 1
• Level ........................................................... 1
• Phillips Screwdriver #2 ............................... 1
• Open-End Wrenches 8, 10, 13mm ......1 Ea.
• Hex Wrenches 3, 4, 5, 6, 8mm ............1 Ea.
• Dust Collection System .............................. 1
• Dust Hose 4" .............................................. 1
• Hose Clamps 4" ......................................... 2
• Branch Line 4" ............................ As Needed
• Y-Fitting 21⁄2" x 4" x 4" ................ As Needed
• NEMA L15-30 Plug (G0623X3) . . As Needed
Needed for Setup
SECTION 3: SETUP

-18- Model G0623X/G0623X3 (Mfd. Since 05/22)
Figure 4. Table saw.
Crate Inventory (Figure 4) Qty
A. Table Saw Body ......................................... 1
A
Inventory Items (Figure 5) Qty
B. Large Extension Table ............................... 1
C. Small Extension Table ................................ 1
D. Hose Support ............................................. 1
Inventory Items (Figure 6) Qty
E. Crosscut Fence .......................................... 1
F. Support Bar ................................................ 1
G. Crosscut Table ........................................... 1
H. Crosscut Table Support Leg ....................... 1
I. Flip Stops ................................................... 2
J. Lock Lever M12-1.75 x 55 ........................... 1
K. Flat Washer 12mm ..................................... 1
L. T-Nut M12-1.75 ............................................ 1
Figure 6. Crosscut table items.
EF
IG
L
K
J
H
Figure 5. Extension table items.
B
C
D
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
Inventory
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.