Groz S3140 User manual

INSTRUCTION MANUAL
S3140, REV A
MTB-7
7 Drawer
Portable Workstation
CAT NR. DESCRIPTION
MTB/7 7 Drawer Portable Workstation
SPECIFICATIONS
Manufactured from heavy
gauge steel sheet
Rugged double wall
construction for enhanced
durability
Corrosion resistant powder
coated finish
Drawers with ball bearing
slides for 100% opening
All drawers lined with 2mm
vinyl sheet
Integrated centralized
locking system to lock/
unlock all drawers in a
single operations
4 heavy duty castors
5" × 2" (125 mm × 50 mm)
Rear castors with brakes
for safety
Ergonomic handle for ease
of movement
Rubber mat top for
protection from scratches
& damage
OVERALL DIMENSIONS (W xD xH) 27" ×18" ×39" (679 mm ×461 mm ×1000 mm)
CASTER SIZE (DIAMETER xWIDTH) 5" ×2"
OVERALL WEIGHT OF CABINET 54 Kg
CABINET TOP Rubber Mat
DOUBLE WALL
CONSTRUCTION
BALL
BEARING
TROLLEY LOAD
CAPACITY
450
KG
AVG. DRAWER
LOAD CAPACITY
45 KG
Double wall steel
construction
Heavy duty
side handle
Self locking ball
bearing drawer
slides
Castors feature
2 fixed and 2 swivel
with toe lock
Rubber mat to avoid
scratches
Centralized
locking system
Depth (D)
Height (H)
Width (W)

2
SAFETY INFORMATION
• Keep the work area clean and dry. Damp
or wet work areas can result in injury.
• When not in use, workstation should be
stored in a dry location to inhibit rust.
• Do not modify this workstation, and do
not use this workstation for a purpose for
which it was not intended.
• Check for damaged parts. Before using
this product, carefully check that it will
operate properly and perform its intended
function. Replace damaged or worn parts
immediately.
WARNING!
• Read and understand all instructions.
Failure to follow all instructions listed
above may result in serious injury.
PACKAGE CONTENT
DESCRIPTION QTY.
7 Drawer Portable Workstation 1
Side handle 1
Bolt & washer set (Size 10 mm) 4
Fixed Caster 2
Swivel Caster with toe lock 2
Bolt & washer set (Size 13 mm) 16
O.I.P.M. 1
TOOLS NEEDED
• 10 mm spanner
• 13 mm spanner / 1/2” spanner
BEFORE INSTALLATION
• Check that the product has not suered
any damage during transport or storage.
• Keep the workstation away from heat and
sharp edges.
INSTALLATION
1. Put the workstation up-side down on the
floor and attach the 4 castors on the base
of workstation using bolt & washer sets
(Size 13 mm)
Note: Swivel caster with toe lock should
be mounted on the same side as the
handle.
2. Now keep the workstation upright. Insert the
side handle into the cabinet wall and attach
with bolt & washer sets (Size 10 mm).
Note: The side handle should be mounted
on the same side as the swivel caster with
toe lock.
3. The workstation is ready to use.
4. To remove a drawer with roller slides, pull
the drawer completely out. Press down
the left tab and lift up the right tab on the
sliders, pull drawer o slides.
5. To reinstall the drawer, realign it with the
internal drawer slide and push in until locked
in place.
OPERATING INSTRUCTIONS
• To avoid tipping, open one drawer at a time.
• Close all drawers when moving the unit.
• Every workstation has a unique number written
on its lock. Only the key with that number can
be used to lock or unlock the drawers.
• Close all drawers before locking. If a drawer is
not locked, unlock the unit and push drawer
to the closed position and then lock the unit
again.
MAINTENANCE
Periodically lubricate casters and tighten all
hardware
DISPOSAL
The components or the used product must be
given to companies that specialize in the disposal
and recycling of industrial waste.

3

Groz Engineering Tools (P) Ltd.
Groz Net Industries
Village Kherki Daula, National Highway-8,
Gurugram-122001, Haryana, INDIA
Tel [phone]
Fax [phone]
E-Mail [e-mail]
Url www.groz-tools.com
The GROZ name, GROZ logo and the mark are
trademarks of GROZ Engineering Tools (P) Ltd., India
GROZ WARRANTY POLICY
GROZ makes all eorts to ensure that its products meet the highest standards of quality and durability and warrants to the original purchaser its
range of products for a period of 12 months from GROZ Invoice date, against defects in materials and workmanship. If the GROZ product is part of
a set, only the portion that is defective is subject to this warranty.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, wear and tear, negligence or accident, repairs or alterations
outside GROZ plants, or to lack of maintenance. GROZ shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special or consequential damages arising from the use of its products. It is upto the user to determine suitability and safety of the
product for their intended use, and the user assumes all risks and liability herewith.
In no event, shall GROZ’s liability exceed the invoiced cost of the product In case of identification of defect covered under this warranty, the same
must be notified in writing to GROZ /GROZ designated authorized service location. Proof of purchase date must accompany the complaint. GROZ
reserves the right to call back the faulty unit, all charges including transportation prepaid. On verification of the defect, the unit will be repaired or
replaced with a new or reconditioned product or part of equal utility or a full refund given at GROZ’s discretion. The repaired /replaced units will be
returned to the user freight prepaid, using most economical freight carrier. However if determined that the defect resulted from causes not within
the scope of the warranty, then the cost of returning the product would be to buyer’s account.