Grundig GCT-K0123T User manual

Thank you for purchasing our product. If there
are any questions, or requests, please do not
hesitate to contact the dealer.
This manual may contain several technical
incorrect places or printing errors, and the
content is subject to change without notice.
The updates will be added to the new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
Privacy Notice
Surveillance laws vary by jurisdiction. Check
all relevant laws in your jurisdiction before using
this product for surveillance purposes to ensure
that your use of this product conforms.

camera parameters and functions.
Disclaimer Statement
Underwriters Laboratories Inc. (”UL”)has not
tested the performance or reliability of the
security or signaling aspects of this product.

hazards as outlined in Ul’s Standard(s) for Saf-

the performance or reliability of the security or
signaling aspects of this product. UL makes no

regarding the performance or reliability of any
security or signaling related functions.

2 MEGAPIXEL
FULL HD INTEGRATED
HD-TVI CAMERA LED
User Manual
1 INTRODUCTION
1.1 Product Features
This series of camera adopts new generation
sensor with high sensitivity and advanced circuit
design technology. It features high resolution,
low image distortion and low noise, etc., which
makes it suitable for surveillance system and
image processing system.
• High performance CMOS sensor and
high resolution bring high-quality image;
• Low illumination;

• Support auto white balance, auto gain control,
electronic shutter control;
• Support image effect adjustment;
• Unit transmission control;

installation requirements.
1.2 Overview
Figure 1-1 Overview
2 INSTALLATION
Before you start:
• Please make sure that the device in the
package is in good condition and all the
assembly parts are included.
• Make sure that all the related equipment is
power-off during the installation.

installation environment.
• Check whether the power supply is matched
with your power output to avoid damage.
• Please make sure the wall is strong enough to
withstand three times the weight of the
camera and the mounting.
• If the wall is the cement wall, you need to
 
camera. If the wall is the wooden wall, you can
use self-tapping screw to secure the camera.
• If the product does not function properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.
Sun Shiel d
Mountin g Bas e
Power Cabl e
HD Video Cabl e
Lens
2.1 Ceiling Mounting
Steps:
1. Drill the screw holes in the ceiling according
to the supplied drill template.

into the screw holes.

 Route the cables to the cable hole and connect
the corresponding power cable and video cable.

screws.

5. Adjust the surveillance angle.

 


tilting position (0° ~ 90° ).

5).Loosen No.1 adjusting screw to adjust the
 
6).Tighten No.1 adjusting screw.

All Screw Holes: for
mounting bas e

Regulatory Information
EU Conformity Statement
This product and - if applicable - the
supplied accessories too are marked
with „CE“ and comply therefore with
the applicable harmonized European standards




Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European Union.
For proper recycling, return this product to
your local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated collecti-
on points. For more information see:
www.recyclethis.info.

This product contains a battery that
cannot be disposed of as unsorted
municipal waste in the European Union.

information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd),
lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your supplier
or to a designated collection point. For more informati-
on see: www.recyclethis.inf
FCC Information
FCC compliance: This equipment has been tested
and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio
communications. Operation of this equipment in
a residential area is likely to cause harmful inter-
ference in which case the user will be required to

FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.

received, including interference that may
cause undesired operation.

3 MENU OPERATION

-
tely) or calling the preset No.95 you can select the
menu and adjust the camera parameters.
3.1 Format

3.2 Setup
Move the cursor to SET UP, and press menu button
to enter the SET UP sub menu.
3.2.1 AE
Move the cursor to AE, and you can adjust the
image brightness by the BRIGHTNESS,
EXPOSURE MODE, and AGC.
Brightness:
Brightness refers to the brightness of the image.
Exposure Mode:

BLC. When

BLC mode can be adjusted,

 
AGC:
AGC optimizes the clarity of image in poor light
scene. AGC level can be set as OFF, LOW,
MIDDLE and HIGH.
3.2.2 WB
Move the cursor to WB, and you can set White
Balance mode as AWB and MWB in this menu.
VIDEO
SETTING

WB RESET
BRIGHTNESS MODE
INFRARED
SMARTI R
CONTRAST
SHARPNESS
SATURATION

AE
DNR
MIRROR

AGC

EXPOSURE
1.BRIGHTNESS
2.EXPOSURE MODE
LEVEL
3.AGC
4.RETURN
5
BLC
5
MIDDLE
WB
MODE MWB
RG IAN1 -|--10
BG AIN1 -|--10
RETURN
AWB: white balance is being adjusted automatically.
MWB: Set the R GAIN/B GAIN value from 1 to 100.

3.2.3 DAY & NIGHT
Move the cursor to DAY & NIGHT, and select
COLOR, B/W, or SMART as the DAY & NIGHT mode.
COLOR: The image is colored in day mode all the time.
B/W: The image is black & white all the time, and
the IR LED turns on in the low-light conditions.
SMART:
and to set the Smart IR level from 1to 16. As shown


3.2.4 VIDEO SETTING
Contrast:
Contrast enhances the difference in color and light
between parts of an image. You can set the value
from 1 to 10.
Sharpness:
Sharpness determines the amount of detail that
an imaging system can reproduce. You can set the
value from 1 to 10.
Saturation:
You can set the saturation level of the image. The
value is from 0 to 10.
DNR:
DNR decreases the noise effect, especially in low
light conditions and delivers more accurate and
sharp image quality. You can set the value from 0
to 7.
Mirror:
You can set the Mirror status as H, V, HV, or OFF.
3.2.5 Reset
Reset all the settings to the default.
3.2.6 EXIT

3.2.7 SAVE/EXIT


T
MODE SMART
INFRARED OFF
SMARTI R0 -|--5
RETURN
NOTE