Grundig GD-CI-BP2647P User manual

Quick Guide
About this guide
The guide includes instructions for using and managing the product.
Pictures, charts, images and all other information hereinafter are for
description and explanation only. The information contained in the
guide is subject to change, without notice, due to firmware updates
or other reasons. Please find the latest version at WWW.GRUNDIG-
SECURITY.COM
Limitation of Liability / Legal Disclaimer
Abetechs GmbH (Grundig Security) undertakes all reasonable efforts
to verify the integrity and correctness of the contents in this
document, but no formal guarantee shall be provided. Use of this
document and the subsequent results shall be entirely on the user’s
own responsibility. Abetechs GmbH (Grundig Security) reserves the
right to change the contents of this document without prior notice.
Design and specifications are subject to change without prior notice.
The product described herein, with its hardware, software and
documentation is provided “as is”, without any warranty, expressed
or implies, including without limitation, merchantability, satisfactory
quality, fitness for a particular purpose, and non-infringement of a
third party.
In no event will our company and its employees or agents be liable to
you for any special, consequential, incidental, or indirect damages,
including among others, damages for loss of business profits, business
QG-GD-CI-BP2647P-2021-07-27-V5-EN ©ABETECHS GMBH, DÜSSELDORF, GERMANY

2
interruption, or loss of data or documentation, in connection with the
use of this product, even if our company has been advised of the
possibility of such damages.
Regarding to products with internet access, the use of the product
shall be wholly at your own risks. Our company shall not take any
responsibilities for abnormal operation, privacy leakage or other
damages resulting from cyber-attack, hacker attack, virus inspection,
or other internet security risks; however our company will provide
timely technical support if required. Surveillance laws vary by
jurisdiction before using this product in order to ensure that your use
conforms to the applicable law. Our company shall not be liable in the
event that this product is used with illegitimate purposes.
In the event of any conflicts between this manual and the applicable
law, the later prevails.
Trademark
Each of trademarks herein is registered. The name of this product and
other trademarks mentioned in this manual are the registered
trademark of their respective company.
Copyright of this document is reserved. This document shall not be
reproduced, distributed or changed, partially or wholly, without
formal authorization.
OPEN SOURCE SOFTWARE LICENSE INFORMATION
The software components provided with Grundig products may
contain copyrighted software that is licensed under various open

3
source software licenses. For detailed information about the
contained open source software packages, the used package versions,
license information and complete license terms, please refer to the
product detail pages on our website. The complete open source
software license information is also included in firmware files of
affected products. Please also check your product’s CD-ROM and
manuals for additional information.
You may obtain the complete corresponding open source part of a
specific product from us for a period of three years after our last
shipment of this product by sending an email to: info@grundig-
security.com
Safety and Installation Instructions
Introduction
Please read these instructions carefully and keep them for future
reference. You must heed all the warnings and cautions as well as
follow all the safety and installation instructions.
The appearance of the products, functions and firmware or software
upgrade may differ from this manual.
GRUNDIG reserves the right to perform needed changes without prior
notice.
Safety Instructions
Make sure that you only use the power adapter that is specified in the
specifications sheet of the product. If you use any other adapter or

4
connect the power supply incorrectly, this may cause explosion, fire,
electric shocks or damage the product. Do not connect several devices
to one power adapter as this may cause an adapter overload and can
lead to over-heating and fire. Make sure that the plug of the power
adapter is firmly connected to the power socket.
Do not place containers with liquids on the product. Do not place
conducting items like tools, screws, coins or other metal items on the
product. These may fall from the product or can cause fire or electric
shocks or other physical injuries.
Do not push or insert any sharp items or any objects into the device as
this may cause damage to the product, fire, electric shocks and/or
physical injuries.
Do not block any ventilation openings, if there are any. Ensure that the
product is well ventilated to prevent any over-heating.
Do not subject the device to physical shock or drop the product.
If the product uses batteries, please use a battery type that is
recommended by the manufacturer. Improper use or replacement of
the battery may result in the hazard of explosion.
Do not use any accessories that are not recommended by GRUNDIG.
Do not modify the product in any way.
If the product starts to smell or smoke comes out of the device,
immediately stop using the product and disconnect it from the power
supply to prevent fire or electric shocks. Then contact your dealer or
the nearest service center.

5
If the product does not work correctly, contact your dealer or nearest
service center. Never open, disassemble or alter the product yourself.
GRUNDIG cannot accept any liability or responsibility for problems
caused by attempted and unauthorized repair and maintenance.
Installation Instructions
It is necessary to fix the device firmly if the product is installed on a
wall or ceiling. Do not install the product on surfaces or in places that
are vibrating. Do not install the product near radiation sources.
Do not install the product near heat sources, like radiators or other
equipment that produces some heat. If the product is not classified by
any IP class, do not install the product in very cold or hot temperatures
(please refer to the working temperature specified in the specification
sheet of the product), dusty, dirty or damp environment.
If the product is classified by any IP class, never touch the product
cover directly with your fingers, because the acidic sweat of the fingers
may damage the surface coating of the product cover. To clean the
inside and outside of the product cover, use a soft and dry cloth. In any
case, do not use alkaline detergents. The correct configuration of all
passwords and other security settings is the sole responsibility of the
installer and/or end-user (this applies especially to IP Cameras and
Recorders).
Special Installation Instructions for Cameras

6
Do not touch the sensor module with your fingers. Do not aim the
camera or camera lens at a strong light such as the sun or a bright
lamp. Irreversible damage to the camera can be caused by a strong
light.
Do not expose the sensor of the product to laser beams as this may
damage the sensor.
If the product supports IR, you need to take some precautions to
prevent IR reflection. Do not install the product close to reflective
surfaces of objects as this may cause reflection. If the product has a
dome cover, please remove the protection film only after installation
to prevent dust or grease on the camera which can cause reflection.
The foam ring around the lens must be seated flush against the inner
surface of the bubble to isolate the lens from the IR LEDS. Fasten the
dome cover to the camera body so that the foam ring and the dome
cover are attached seamlessly.
For cleaning, use a clean cloth with a bit of ethanol and wipe it
carefully and gently. In any case, do not use alkaline detergents.
If a glove is provided in the package, please use it to open the product
cover. Never touch the product cover directly with fingers, because
the acidic sweat of the fingers may damage the surface coating of the
product cover.
Special Installation Instructions for IP Cameras
Make sure that the latest firmware is installed on the IP Device. You
may get the latest firmware from www.grundig-security.com
website or from [email protected]m.

7
Table of Contents
1 Overview ......................................................................................... 8
1.1 Cable Descriptions .................................................................... 8
1.2 Alarm Output ............................................................................ 9
2 Installation ..................................................................................... 10
2.1 Installing the Memory Card .................................................... 10
2.2 Installing PTZ Camera.............................................................. 12
2.2.1 Ceiling Mounting .............................................................. 12
2.2.2 In-ceiling Mounting .......................................................... 17
3 Setting the PTZ Camera over the LAN ............................................ 20
3.1 Wiring ..................................................................................... 20
3.2 Activating the Camera ............................................................ 21
3.2.1 Activation via Web Browser ............................................. 21
3.2.2 Activation via Grundig IP-Finder Tool ............................... 22
3.3 Modifying the IP Address ........................................................ 24
4 Accessing via Web Browser ........................................................... 26
4.1 Initializing the Memory Card ................................................... 28

8
1 Overview
1.1 Cable Descriptions
The cable interfaces of network PTZ camera are shown in Figure 1-1.
The cables are distinguished by different colors. Refer to the labels
attached on the cables for identification.
Note:
 Make sure the camera is power-off before you connect the
cables.
Figure 1-1 Cables of PTZ Camera

9
No. Description
1 Power supply interface (12 VDC)
2* Audio input and output interface
3* Alarm input and output interface
4 RJ45 self-adaptive network interface (PoE)
5 Mounting base
6 Black liner
7 Lens
8 Bubble
1.2 Alarm Output
Alarm output is shown in Figure 1-2.
Figure 1-2 Alarm Output

10
2 Installation
Before you start:
Check the package contents and make sure that the device in the
package is in good condition and all the assembly parts are included.
Notes:
 Do not drag the PTZ camera with its waterproof cables;
otherwise the waterproof performance is affected.
 Do not touch the bubble directly by hand. The image blurs
otherwise.
 Do not power up the camera until the installation is finished. To
ensure the safety of personnel and equipment, all the
installation steps should be done with power supply off.
2.1 Installing the Memory Card
You can install the memory card for local storage.
Steps:
1. Remove the four silicone plugs on the decorative rim as shown in
Figure 2-1, and you can see four flange screws in the decorative
rim.

11
Figure 2-1 Remove the Silicone Plugs
2. Loosen four flange screws with a screwdriver. Remove the bubble
and the decorative rim as shown in Figure 2-2.
Figure 2-2 Remove the Bubble and the Decorative Rim
3. Open the memory card cover and insert the memory card into the
card slot as shown in Figure 2-3.

12
4. Close the memory card cover. Fix the four flange screws and push
four silicone plugs back to assemble the PTZ camera.
2.2 Installing PTZ Camera
The PTZ camera supports ceiling mounting and in-ceiling mounting.
Note:
Wall mounting, pendant mounting and installation with junction box
are supported for the PTZ camera. The corresponding accessories
shall be purchased separately.
2.2.1 Ceiling Mounting
Purpose:
There are two ceiling mounting types provided for the camera, and
we take the mounting without the junction box as the example.

13
Before you start:
The ceiling mounting is applicable to the indoor/outdoor solid ceiling
construction. The followings are the mandatory precondition for
ceiling mounting:
• The thickness of the ceiling shall range from 5mm to
40mm.
• Make sure the ceiling is strong enough to withstand
more than four times the weight of the PTZ camera and
its accessories.
Wiring
The cables of PTZ camera can be routed either from the top or the
side of the back box, as shown in Figure 2-4.
For the cables routed from the top of the back box, it is required to
drill a cable hole in the ceiling.
Figure 2-4 Cabling for PTZ Camera

14
Ceiling Mounting without Junction Box Steps:
5. Rotate the base plate counterclockwise to separate it from the PTZ
camera.
6. Attach the drill template (supplied) to the place where you want to
fix the PTZ camera, and make sure the front arrow appoints to the
monitoring area.
Figure 2-5 Attach the Drill Template
7. Drill a cable hole in the ceiling according to the circle A on the
template if you want to route the cables through the ceiling. Pull
out the cable slot cover if you want to route the cables on the
surface of the ceiling, as shown in Figure 2-6.
Figure 2-6 For PTZ Camera

15
8. Attach the base plate to the ceiling and secure it with the supplied
three self-tapping screws by aligning with three screw holes in the
ceiling, and the front arrows on the drill template and base plate
should be aligned together as well, as shown in Figure 2-7.
9. Route the cables through the cable hole.
10. Align the PTZ camera with the base plate. Rotate the PTZ
camera clockwise into the base plate, and the PTZ camera is
secured with the base plate by three locks on the plate.

16
Figure 2-8 Secure the PTZ Camera
Note:
After the PTZ camera is installed, tighten the fixing screw with a
screwdriver as shown in Figure 2-9.
Figure 2-9 Tighten the Fixing Screw

17
2.2.2 In-ceiling Mounting
Notes:
 Reserve at least 250 mm of height for in-ceiling mounting.
 The thickness of the ceiling shall range from 5mm to 40mm.
 Make sure the ceiling is strong enough to withstand more than
four times the weight of the PTZ camera and its accessories
Steps:
1. Rotate the base plate counterclockwise to separate it from the PTZ
camera, as shown in Figure 2-10.
Figure 2-10 Separate the Base Plate from the PTZ camera
2. Attach the drill template (supplied) to the place where you want to
fix the PTZ camera, and drill a hole in the ceiling according to the
template.

18
Figure 2-11 Drill Template
3. Align the cable holes of the base plate to the cable holes of the in-
ceiling bracket and then fix the base plate onto the bracket with
the four screws in the package (supplied), as shown Figure 2-12.
Figure 2-12 Fix the Base Plate to In-ceiling Bracket
4. Connect the cables and route the cables through the cable hole.
5. Align the PTZ camera with the base plate. Rotate the PTZ camera
clockwise into the base plate, and the PTZ camera is secured with
the base plate by three locks on the plate.
6. Fix the screws on the side with a screwdriver, as shown in Figure 2-
13.

19
Figure 2-13 Fix the Camera
7. Place the camera and the bracket into the hole drilled in step 2,
and rotate the screws clockwise to fix the camera.
8. Fix the decorative rim with the bubble and the decorative rim will
be attached to the in-ceiling bracket automatically, as shown in
Figure 2-14.
Figure 2-14 Assemble the Decorative Rim