GSWeb Playground Equipment ROLLING HILLS GS-RH104 Installation and operating instructions

GSWeb Playground Equipment E-mail) gswebin[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
ROLLING HILLS MODEL NO.
Rev_2
2016.05
GS-RH104
1
INSTALLATION & MAINTENANCE INSTRUCTIONS
Ages : 5 to 12 years
Capacity : 214 children
Size : L19.0m x W4.76m x H2.63m
Use zone : L23.0 x W9.76
▲Completed Net
Features
The Rolling Hills features GS Web Technology which includes
the highest steel content and the strongest connection
materials in the industry, including a steel-wire core
in our edge ropes and connection points crushed in place with
over 75 tons of pressure to ensure long life of the games
and maximum safety for the children.
GS Web Nets help bring movement, balance, exercise and fun
back into the playground.

GSWeb Playground Equipment E-mail) gswebin[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
ROLLING HILLS MODEL NO.
Rev_2
2016.05
GS-RH104
2
Safety area and Fall Height zone
▲Fall Height and safety area
Safety area
The requirements for space and safety clearances are taken from
BS-EN 1176-1 / ASTM-F1487 / CSA Z614
The use zone for stationary play equipment shall extend no less than
72 in. (1830mm) from all sides of the play structure.
Fall Height : 2900mm (from surface)
The Fall height on the external surface of a pyramid shaped space net
is the highest point attainable on the edge of the structure where an
unimpeded fall to the protective surface is possible. This height is based
on the center of gravity height of the maximum user.
SAFETY ZONE
(EN)
G.L
SAFETY ZONE
(ASTM)
1,500 (EN)
2,500(EN)
1,830 (ASTM)
1,830(ASTM)
1,830 (ASTM)
23,515 (ASTM)
22,853 (EN)
10,145 (ASTM)
100 EPDM
100 EPDM
2,900
3,000
9,400 (EN)

GSWeb Playground Equipment E-mail) gswebin[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
ROLLING HILLS MODEL NO.
Rev_2
2016.05
GS-RH104
3
Foundation Information
!Attention
Please refer to following details for foundation work.
Base plates are welded to the Rolling Hill‟s pipe. After assembling
pipes and nets, fix the structure on the concrete.
700
700
3,700
700
700 700
700 700
700
700 1,430 3,700 700 4,830 700 2,415 700
700550700550700
500
500
2,005
1,345
1,345 1,800
250
250
250
1,800
250 700
1,800
550
700550
F1
F3
F2
F4
F4
F4
F4
F4
F4
F4
3,140
6,890
1,640
1,685
2,300
1,905

GSWeb Playground Equipment E-mail) gswebin[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
ROLLING HILLS MODEL NO.
Rev_2
2016.05
GS-RH104
4
Post Plate Assembly
Foundation Detail F1, F2, F3, F4
Pouring Concrete
Pour concrete* into wooden support frame until flush to top edge
Allow 3-5 days for concrete to cure before proceeding to next step.
*Concrete is to be wet concrete with
minimum 25 MPA / 3500PSI.
3,700
3,700
300
3,844
300
1,640 3,700
300
700
700
700
700
F1
1,640
2,300
500
500
6,890
3,844
<FOUNDATION 1> <FOUNDATION 2> <FOUNDATION 3> <FOUNDATION 4>

GSWeb Playground Equipment E-mail) gswebin[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
ROLLING HILLS MODEL NO.
Rev_2
2016.05
GS-RH104
A
B
C
D
E
F
G
H
I
J
K
5
OVERALL ASSEMBLY
Overall Assembly
Assemble the parts in the following order:
1. Check names of the parts.
- From “A” to “K” are Pipe‟s name.
2. To prevent any confusion, Divide all parts into groups,
Outside and Inside as below.
!Attention
It is very important to keep the stickers attached on the parts on until
the installation is completed.
If the stickers are detached during the installation, it might be difficult to
check whether the parts are correctly assembled in correct order and
position.
Quite much recommended to take care that no sticker is detached before
installation is completely finished.
The information on stickers is made up of part name and number such as
“A”~”K”.. etc.
Assembly order
E → D →F →C → K → G → I → J → B → H → A

GSWeb Playground Equipment E-mail) gswebin[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
ROLLING HILLS MODEL NO.
Rev_2
2016.05
GS-RH104
6
OVERALL ASSEMBLY
Overall Assembly
Assemble the pipes in alphabetical order.
1. Check the pipes‟ numbers on Stickers on them.
2. As below picture, Line up the pipes and Connect the pipe to the next pipe
3. Set the holes on the pipe and put bolts into the holes.
4. Fasten the bolts.
5. Repeat with the others in the same way.
Bolt
M12 x L35
“B” “A” “B” “A”

GSWeb Playground Equipment E-mail) gswebin[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
ROLLING HILLS MODEL NO.
Rev_2
2016.05
GS-RH104
7
OVERALL ASSEMBLY
Overall Assembly
Assemble the parts in the following order:
1. Check the net‟s name. There are 6 set net from Net A to Net E.
2. Attach the net to the proper location of pipe in order as below picture.
Fix Bolt
M6 x L15
Frame
Frame
Fix Nut
M6 x L15
Net D
Net C
Net E
Net E
Net B
Net A

GSWeb Playground Equipment E-mail) gswebin[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
ROLLING HILLS MODEL NO.
Rev_2
2016.05
GS-RH104
8
OVERALL ASSEMBLY
Overall Assembly
3. As below picture, Connect the Net „A‟ and „B‟ with double clip.
4. Repeat with Net „B‟-‟C‟.
M10 Nut
Bolt
M10 x L30 Double Clip

GSWeb Playground Equipment E-mail) gswebin[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
ROLLING HILLS MODEL NO.
Rev_2
2016.05
GS-RH104
9
OVERALL ASSEMBLY
Overall Assembly(for Hammock)
1. Insert the Hammock‟s post into Rolling hills pipe and assemble.
2. Check the location of the hammock.
3. Assemble the hammock to the post with Clamp.
4. Fix the post onto the concrete.
3,000
700500
3,000
1,485
F.L
"HP_1"
"HP_2"
EYE BOLT
POST
BOLT Clamp
BOLT
Set Anchor
! Attention
Do not drill holes on the concrete first.
After checking the tension of the stair net and
setting its distance, put the Set Anchor on concrete.

GSWeb Playground Equipment E-mail) gswebin[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
ROLLING HILLS MODEL NO.
Rev_2
2016.05
GS-RH104
10
OVERALL ASSEMBLY
Overall Assembly (for Climbing Ropes)
1. Fix the Climbing ropes onto the concrete.
Set Anchor
! Attention
Do not drill holes on the concrete first.
After checking the tension of the stair net and
setting its distance, put the Set Anchor on concrete.

GSWeb Playground Equipment E-mail) gswebin[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
ROLLING HILLS MODEL NO.
Rev_2
2016.05
GS-RH104
1
2
3
4
5
6
PARTS LIST
Parts check list
A~E. Net
1. Pipe
2. Hammock
3. Climbing Ropes (Disk)
4. Chemical Anchor
5. Set Anchor
6. Set Anchor
11

GSWeb Playground Equipment E-mail) gswebin[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
ROLLING HILLS MODEL NO.
Rev_2
2016.05
GS-RH104
12
Maintenance
A. General safety measures
On the playground there should be a sign(pictogram) giving the following information:
a) general emergency telephone number;
b) telephone number to contact maintenance personnel;
c) name of the playground;
d) address of playground; and
e) other relevant local information, if applicable.
The entry, exit and emergency paths to and from a playground, intended for use by the public and emergency services, should be accessible
and free of obstacles at all times.
NOTE Attention is drawn to local regulations.
B. Procedures
Defects that occur during operation and which put safety at risk should be corrected without delay. If this is not possible, the equipment
should be secured against use e.g. by immobilization or removal.
There should be written operational procedures covering the measures to be taken in the event of accidents, fire and the like.
Until unsafe equipment is repaired and released for use, access by the public should be prevented. Information about accidents brought to
the attention of the manager should be recorded on a form that includes the following details:
a) date and tie of accident;
b) age and sex of victim and clothing worn, Including footwear;
c) equipment involved;
d) number of children on site at the time of the accident;
e) description of accident;
f) injury sustained including part(s) of body affected;
g) action taken;
h) witness statements;
i) any subsequent equipment modification;
j) weather conditions; and
k) any other relevant information.

GSWeb Playground Equipment E-mail) gswebin[email protected]
Website) www.gsweb21.com
Tel) [phone]
Fax) [phone]
65, Saengnim-daero 259beon-gil, Saengnim-Myeon
Gimhae-si, Gyeongsangnam-do, Republic of Korea
ROLLING HILLS MODEL NO.
Rev_2
2016.05
GS-RH104
13
Maintenance
C. Routine maintenance
To reduce accidents, the owner or operator should ensure that an appropriate routine maintenance schedule is established, implemented and
maintained. This should take into account local conditions and the manufacturer's instructions that can affect the necessary inspection
frequency. The schedule should list the components to be maintained and should also give procedures for dealing with complaints and
breakdowns.
The routine maintenance of playground equipment and surfaces should consist of preventative measures to maintain their level of safety,
performance and compliance with the relevant part(s) of EN 1176. Such measures should include:
a) tightening of fastenings;
b) re-painting and re-treatment of surfaces;
c) maintenance of any impact attenuating surfaces;
d) lubrication of bearings;
e) marking of equipment to signify loose fill finished surface level;
f) cleaning;
g) removal of broken glass and other debris or contaminants;
h) restoring loose fills to the correct level; and
i) maintenance of free space areas.
D. Corrective maintenance
Corrective maintenance should include measures to correct defects, or th re-establish the necessary levels of safety of the playground
equipment and surfaces. Such measures should include:
a) replacement of fastenings;
b) welding of welding repairs;
c) replacement of worn or defective parts; and
d) replacement of defective structural components.
E. Personal safety
Repairs during operation that could put the safety of maintenance personnel of the public at risk, should be avoided.
F. Equipment alterations
Alterations to parts of a piece of equipment or structure that could affect the essential safety of the equipment should only be carried out
after consultation with the manufacturer or a compete person.