GU Electronic FD-PAS-170327 User manual

Ford Sync2 TDC2
- MODEL : FD-PAS-170327
- DATE : 2020.03.25

GU Electronic
Index
1. Main Spec
2. Block Diagram
3. Dimension
4. External Appearance
5. Connector Pin Assignment
6. Product Composition
7. DIP S/W Setting
8. Mode Change
9. Touch Control
10. OSD(On Screen Display) Control
11. Install Manual
12. Q & A

GU Electronic
1. Main Spec.
1. Input Spec. (MULTI VIDEO INTERFACE)
- 1 x Digital RGB Input (Navigation System source)
- 1 x Analog RGB Input (Navigation System output)
- 1 x CVBS(REAR CAMERA) Input. (Rear camera source)
- 1 x CVBS(FRONT CAMERA) Input. (Front camera source)
2. Output Spec.
- 1 x Vertual Analog Touch (Navigation System source)
- 1 x Uart Digital Touch (Navigation System source)
- 1 x LVDS Output (LCD Operation)
3. Power Spec.
- Input Power : 8VDC ~ 24VDC
- Consumption Power : 12Watt, Max
4. Switch Input mode
- Possible to select CAR model while switching mode by DIP S/W
- By button on the Commander in the car via CAN

GU Electronic
2. Block Diagram
Scaler
(PIP)
MCU
INTERFACE
CAR
COMMAND
SYSTEM CAN
EEPROM
CAN
RECEIVER
LVDS
TX
REAR CAMERA
POWER
REAR CAMERA
LVDS
LVDS
FRONT CAMERA COMPOSITE
NAVIGATION
SYSTEM
CAR
TFT-LCD
SUB
BOARD
RELAY

GU Electronic
3. Dimension
156mm * 83mm * 22mm
* This can change under manufacturer’s circumstance
156mm
83mm
22mm

GU Electronic
4. External Appearance
LED DIP S/W PROGRAM
FRONT
IMAGE
REARNAVIPOWER/CAN
R-TOUCH
Digital
RGB
LCD-OUT

GU Electronic
4. External Appearance
LEDDIP S/W
PROGRAM IMAGE
R-TOUCH
FRONT
REARNAVIPOWER/CAN
Digital
RGB
LCD-OUT

GU Electronic
5. Connector Pin Assignment
*NAVI Connect
① R DATA (Red)
② G DATA (Green)
③ B DATA (Blue)
④ SYNC (White)
⑤ GND (Black)
⑥ DMB IR (Green)
⑦ DVD IR (Orange)
①②③④⑤⑥⑦
*Touch Connect
① Y-
② X-
③ Y+
④ X+
① ② ③ ④
*POWER Connect
1. Battery (Yellow)
2. Battery (Yellow)
3. Rear-DET (Brown)
4. Front-DET (Blue)
5. CAN-L (Green)
6. CAN-H (Orange)
7. N.C
8. N.C
1 15
2 16
9. N.C
10. N.C
11. ACC (Red)
12. Rear-VCC (Red)
13. Front-VCC (Red)
14. Mode (Green)
15. GND (Black)
16. GND (Black)

GU Electronic
6. Product Composition
Interface 1 EA
FD-PAS-170327
LVDS Cable(800mm) 1 EA
Power Cable 1 EA OSD Board 1 EA
LVDS FFC Cable 2 EA
SUB Board (R01) 1 EA
(80mm)
(100mm)
RGB NAVI Cable 1 EA
Mode S/W 1 EA
Touch FFC Cable(100mm) 1 EA
Touch convertor Cable(KD-900) 1 EA
JIG Board (REV02) 1 EA

GU Electronic
6. Product Composition
* CarPlay Set Sales(option) – KPLAY
Interface 1 EA AUX Cable 1 EA
Power Cable 1 EA HDMI Cable 1 EA
Microphone 1 EA
Bluetooth / Wifi Antenna 2EA

GU Electronic
6. Product Composition
CarPlay Main 1 EA AUX Cable 1 EA
Power Cable 1 EA
HDMI Cable 1 EA
* CarPlay Set Sales(option) – NV17
Microphone 1 EA

GU Electronic
7. DIP S/W Setting
* ON : DOWN , OFF : UP
PIN FUNCTION DIP S/W Selection
1 NAVI ON : Not Used
OFF : Used
2 DVB-T(AV1) ON : Not Used
OFF : Used
3 DVD(AV2) ON : Not Used
OFF : Used
4 N.C
5 N.C
6
CAR type SEL Right Picture7
8
* DIP S/W Example
F150 Model
LINCOLN MKX (2011year)
Explorer Model
Vehicles that do not function as basic
DIP-SW among F150 models

GU Electronic
8. Mode Change
Mode Change Button – F150 Model Streeing Wheel
Select either "Left" button or "Voice" button.
Select "Off" when not using both.
"Left" button
- Switch mode by pressing
for 1.5 seconds
- Short press to switch
OEM
"Voice" button
- Press Mode for 3 seconds.
- Short press to switch OEM

GU Electronic
8. Mode Change
Mode Change Button – Explorer Model Streeing Wheel
Select either "Left" button or "Voice" button.
Select "Off" when not using both.
"Left" button
- Switch mode by pressing for 1.5 seconds
- Short press to switch OEM
"Voice" button
- Press Mode for 3 seconds.
- Short press to switch OEM

GU Electronic
9. Touch Control
Press and hold for more than 11 seconds on
NAVI, DVB-T, DVD screen.
(Note that it only works the first time after
switching screens)
+ Touch according to the shape coordinates
.
OR
OSD menu -> Utility -> Calibration
Touch control - Calibration

GU Electronic
9. Touch Control
DVB-T/DVD Control
Press Icon
DVB-T DVD

GU Electronic
10. OSD(On Screen Display) Control
OSD control
Mode State
First Menu Second Menu Third Menu
MENU Press to display when there is no OSD
screen.
When OSD screen is on, press it to EXIT or
OFF.
SEL Item Selection, Value Selection
UP Item up
Increase selected value
DOWN Item down
Decrease selected value
MENU SEL UP DOWN

GU Electronic
First Menu Second Menu Third Menu Description
Config
NAVI-RGB DIGTAL-INAVI
:Setting the Connected NAVI Model
DVB-T(DMB) ELT_DVBT20
:Setting the Connected DVB-T Model
DVD ELT_980XU Slim
: Setting the Connected DVD Model
RearCam AVM VIDEO
: Setting the Connected RearCam Model
Reset Execute Reset to default value of Config menu
OSD Config
10. OSD(On Screen Display) Control

GU Electronic
OSD - Option Menu
First Menu Second Menu Third Menu Description
Option
NAVI COM
HMS
FINE
:
Set up manufacturer of
woodworking device for UART
Touch use
OFF Do not use features.
RearCam-Type OEM Original Camera
ExtDevice Equipped with external camera
RearCam-Power
ON + 12V continuous supply
AUTO + 12V supply only in Rear
camera mode
OFF + 12V off
RearCam-Det GEAR Detected by CAN
WIRE Detected by Rear-Det Wire
AV Mode ON Use “REAR” video input port as
VIDOE input.
OFF Do not use features.
FrontCam-Type OEM Original Camera
ExtDevice Equipped with external camera
FrontCam-Power
ON + 12V continuous supply
AUTO + 12V supply only in Front
camera mode
OFF + 12V off
FrontCam-Det GEAR Detected by CAN
WIRE Detected by Front-Det Wire
FrontCam-RcvOpt ON After RearCam shows FrontCam
and returns to previous state
OFF Disable feature
10. OSD(On Screen Display) Control

GU Electronic
OSD - Option Menu
First Menu Second Menu Third Menu Description
Option
UI DVB-T (DMB) ON DVB-T device control UI output
function
OFF Disable feature
UI DVD ON DVD device control UI output
function
OFF Disable feature
Reset Execute Option Menu all Reset
10. OSD(On Screen Display) Control