GUIDELINE reelMaster LA User manual
Owners manual
reelMaster
Parts list
Easy care intructions
Changing direction
of retreive
#46
#6/8, #9/11
27
1
2
3
5
6
4
18
17
9
10
13
12
11
14
19
22
21
20
PART NAME
PART NAME
KEY NO KEY NO KEY NO PART NAME PART NAME
KEY NO
7
15
23
28
29
30
8
16
24
32
25
26
31
33
34
35
36
37
38
39
40
41
42
43
44
45
KEY NO PART NAME
SCREW (D/K)
DRAG KNOB
DRAG SHAFT
CLICK PIN
SPRING
SCREW (H/P)
HOUSING PLATE
WASHER
E-CLIP
DRAG PLATE
O-RING
KEY WASHER ("A")
DRAG WASHER(TEFLON)
KEY WASHER ("D")
O/WAY ASS'Y
SHAFT
WASHER
BUSH
FRAME
FOOT
SCREW (FOOT)
WASHER
E-CLIP
O-RING (S/C)
SCREW (BALANCE)
SCREW (H/RIVET)
SPOOL
HANDLE RIVET
HANDLE KNOB
SCREW (H/K)
DRAG WASHER(CARBON)
DRAG WASHER(CARBON)
KEY WASHER ("D")
DRAG WASHER(TEFLON)
27
1
2
3
5
6
4
18
17
9
10
13
12
11
14
19
22
21
20
PART NAME
PART NAME
KEY NO KEY NO KEY NO PART NAME PART NAME
KEY NO
7
15
23
28
29
30
8
16
24
32
25
26
31
33
34
35
36
37
38
39
40
41
42
43
44
45
KEY NO PART NAME
SCREW (D/K)
DRAG KNOB
DRAG SHAFT
CLICK PIN
SPRING
SCREW (H/P)
HOUSING PLATE
WASHER
E-CLIP
DRAG PLATE
O-RING
KEY WASHER ("A")
DRAG WASHER(CARBON)
O/WAY ASS'Y
DRAG WASHER(CARBON)
SHAFT
WASHER
BUSH
FRAME
FOOT
SCREW (FOOT)
WASHER
E-CLIP
O-RING (S/C)
SCREW (BALANCE)
SCREW (H/RIVET)
SPOOL
HANDLE RIVET
HANDLE KNOB
SCREW (H/K)
SPOOL CAP
BALANCE
SPOOL CAP
BALANCE
GUIDELINE reelMaster LA flyreels come with an option of choos-
ing both right hand and left hand retrieve when purchasing them.
These reels incorporate a state of the art sealed carbon/stainless
steel drag system that is resistant to water, dirt and moisture. There
is normally no need to open up the drag cylinder.
However, if you wish to acess it or have the need to change the
direction of the retrieve, please follow the steps below.
Thank you for choosing this carefully designed GUIDELINE flyreel.
We are very proud that you decide to choose one of our products
among so many others.
We sincerely hope it will bring you years of good performance and
many great fish. Please take good care of your reel and try and
follow the instructions below to make sure it will perform to your
highest expectations in the most demanding conditions.
Always rinse or soak your reel in fresh water after using it. Take the
spool off the body, to get best possible access to all areas of the
reel. Remove sand and dirt with a soft, wet sponge or cloth. Rinse
thoroughly after cleaning, especially if you have used the reel in
salt water. Leave the reel to air dry before storing it for your next
trip. There is no need to open the sealed drag system for lubrica-
tion or adjustments. The inside of this reel is maintenance free. If
you want, you can apply a thin layer of grease on the shaft and the
locking areas of the spool.
Back off the drag to the lowest setting when the reel isn’t used.
Store in the protective reel case both on and off the fly rod.
Reelmaster LA owners manual
Thank you for choosing a Guideline Fly Reel.
GUIDELINE fly reels come with a 3-year full service warranty against
manufacturer´s defects in material or workmanship. This guarantee is
valid for the first owner only. The warranty is limited to the repair or
exchange of the product and does not cover any type of damage caused
by neglect, normal wear or misuse.
www.guidelineysh.com I E-mail info@guidelineysh.com I Phone +46 31 92 36 50
1. Remove spool from reel by unscrewing the relase spool cap. (35)
2. Pull the spool off the shaft.
3. Remove the E-clip from the main shaft. (27)
Then pull off the two thin metal washers.
4. Carefully remove the hexagraph screw (1) in the centre of the drag knob.
Pay special attention to the spring and click pin attached underneath.
5. Remove the click pin and the spring (4-5) from the hole.
6.Remove the 3 Philips head screws. (6)
7. Lift off the black housing plate. (7)
8. Lift out the stainless drag plate (10).
9. Remove the rubber o-ring and all washers, (10-15)
The one-way bearing is now exposed. Lift it out, turn it around and replace it,
making sure it is fitted correctly into into remaining washers and the three
slots in the cylinder walls.
10. Replace the washers you removed, making sure they are in same order
as before. Failure to do so may cause malfunction to the reel.
11. Replace the stainless and the Acetal cover plates. Make sure the click
pin and spring are fitted correctly.
12. When attaching the drag setting knob, make sure the numbers are set
so the 6 is in the free spool position. Fasten the centre hexagraph screw.
13. Replace washers and E-clip on the main shaft.
14. Fit the spool in place, making sure the straight edges are aligned on
spool and shaft.
reelMaster
How to change the direction of retreive
Table of contents
