GYM RAX STREAMLINE User manual

GYM RAX® INSTALLATION
STREAMLINE STORAGE
ENGLISH (U.S.)
COPYRIGHT © 2020 GYM RAX INTERNATIONAL, INC. All rights reserved.
Revision 20A

FOREWORD
GYM RAX® INSTALLATION | STORAGE & SUSPENSION SYSTEMS 1 REVISON 20A
FOREWORD
This manual provides information intended for use by persons and professionals who, per
current regulatory requirements, are qualified to install this equipment.
If further information is required, please contact:
GYM RAX International, Inc.
Attn: Customer Success
1730 Berkeley St.
Santa Monica, CA 90404
Phone [phone]
Fax [phone]
[email protected]
www.gymrax.com
We welcome your comments concerning this manual. Although every effort has been made
to keep it free of errors, some may occur. When reporting a specific problem, please
describe it briefly and include the manual part number, the paragraph/figure/table number,
and the page number. Send your comments to:
GYM RAX International, Inc.
Attn: Customer Success
1730 Berkeley St.
Santa Monica, CA 90404
Phone [phone]
Fax [phone]
[email protected]
www.gymrax.com

DOCUMENT REVISION HISTORY
GYM RAX® INSTALLATION | STORAGE & SUSPENSION SYSTEMS 0 REVISON 20A
DOCUMENT REVISION HISTORY
REV
DATE
DETAIL
20A
04/23/2020
STREAMLINE INSTRUCTIONS RELEASE
The information and data in the most recent revision of this document will supersede all
previously published Gym Rax documents and manuals. Please verify your copy is the latest
available by referring to the digital version online available from Gym Rax.

CONTENTS
GYM RAX® INSTALLATION | STORAGE & SUSPENSION SYSTEMS 0 REVISON 20A
CONTENTS
FOREWORD ..........................................................................................................................................1
DOCUMENT REVISION HISTORY ..........................................................................................................0
CONTENTS ............................................................................................................................................0
STREAMLINE STORAGE ASSEMBLY ......................................................................................................1
PLANNING AHEAD...........................................................................................................................1
ESTIMATED INSTALLATION TIME .......................................................................................................1
RECOMMENDED BOLT TORQUE SPECS..........................................................................................1
REQUIRED TOOLS AND SUPPLIES.....................................................................................................1
INSTALL PROCEDURE .......................................................................................................................2
INSTALLATION REFERENCES..................................................................Error! Bookmark not defined.
STREAMLINE FOOTPRINT PLATE POSITIONING AND DIMENSIONS..Error! Bookmark not defined.
END OF DOCUMENT ............................................................................................................................8

STREAMLINE STORAGE ASSEMBLY
GYM RAX® INSTALLATION | STORAGE & SUSPENSION SYSTEMS 1 REVISON 20A
STREAMLINE STORAGE ASSEMBLY
PLANNING AHEAD
•Following the GYM RAX® Storage systems installation sequence is critical to the
performance of the structures and safety of the users.
•Read all instructions before proceeding.
•Review all supplied drawings & packing lists before starting any work.
•Identify any installation uncertainties and contact a GYM RAX customer success
representative for clarification.
•Consider the number of persons required to safely install GYM RAX.
•Plan for the method of installation and tools required.
•Take precautions to avoid damaging finishes.
•Do not over-torque bolted joints as walls of posts and tubes may crush.
•Never leave unsecured or unstable GYM RAX structures unattended.
ESTIMATED INSTALLATION TIME
30 minutes per bay
RECOMMENDED BOLT TORQUE SPECS
1/2” fasteners: 30-35 ft-lbs.
3/8” fasteners: 20-25 ft-lbs.
REQUIRED TOOLS AND SUPPLIES
9/16” & 3/4” drive sockets and/or wrenches
Tape measure
7/32” Allen key
Rubber mallet
Box cutter knife
Level

STREAMLINE STORAGE ASSEMBLY
GYM RAX® INSTALLATION | STORAGE & SUSPENSION SYSTEMS 2 REVISON 20A
INSTALL PROCEDURE
STEP 1 – POST/ANCHOR PLATE ASSEMBLY
A) Insert End Cap into the upper end of Streamline Post. The End Cap should push in by
hand, use a rubber mallet if necessary.
B) Fasten the Self Anchor Plate to the bottom of the Streamline Post using two ½” hex
bolts. Use a ¾” socket or wrench.
SELF ANCHOR PLATE &
HARDWARE
STREAMLINE POST 3’, 4’, OR 6’
END CAP
½”-20 x5/8” HEX BOLTS (2)
(NO WASHERS)

STREAMLINE STORAGE ASSEMBLY
GYM RAX® INSTALLATION | STORAGE & SUSPENSION SYSTEMS 3 REVISON 20A
STEP 2 – ASSEMBLE REMAINING POSTS
A) Assemble remaining Post/Anchor Plate following the procedure in Step 1.
B) Position the Posts rear edge inline and 48” apart on centers.
C) Anchor Plates requires a firm, flat and level ground surface. The Posts should be stable
and not easily rock fore-aft or side to side. Check the ground surface and ensure no
debris is under the plate and the ground surface is flat and level.
REAR EDGE
ADDITIONAL
BAY POSTS
IF MULTIBAY

STREAMLINE STORAGE ASSEMBLY
GYM RAX® INSTALLATION | STORAGE & SUSPENSION SYSTEMS 4 REVISON 20A
STEP 3 – FASTEN CROSSMEMBERS
STREAMLINE
CROSSMEMBER
BACKSIDE
3/8”-16 x3.25” BH BOLTS (6)
(2 PER POST)
I
NSERT ADDITIONAL
CROSSMEMBERS IF
MULTIBAY
CONNECT SHORTER OR
TALLER BAY CROSSMEMBERS
TO HOLE PAIRS WHEN
DIFFERENT SIZED BAYS ARE
CONNECTED

STREAMLINE STORAGE ASSEMBLY
GYM RAX® INSTALLATION | STORAGE & SUSPENSION SYSTEMS 5 REVISON 20A
A) Lift one Crossmember at a time and line up holes with the upper 2 holes of the post.
B) Fasten Post Hook & Crossmembers to Posts with the 3/8” bolts adding washers and nut
as shown. Use a 7/32” Hex Key and a 9/16” wrench or socket.

STREAMLINE STORAGE ASSEMBLY
GYM RAX® INSTALLATION | STORAGE & SUSPENSION SYSTEMS 6 REVISON 20A
STEP 4 – ATTACH RAX CHANNELS
RAX CHANNEL SET
3/8”-16 x3.25” BH BOLTS
(2 PER POST)