Gyration Cyberview3000 User manual

Smart Video Doorbell kit
User manual
Cyberview3000

1. Doorbell*1
2. Mounting bracket*3
3. Use instructions*1
4. USB power cord*1
5. Installation screw kit
(Spare and expansion plugs)*1
6. 3M Adhesive for flat support*1
7. Removal Pin*1
8. Installation wire kit*1
9. Wiring cap (optional)*1
10. Indoor chime kit*1
Packing list
01

Removal hole
Infrared
light
Microphone
Lens
Indicator
light
human body
Infrared sensor
Doorbell
button
Speaker
Port micro-USB
Power button
Micro-SD card
slot
Reboot hole
Exploded views of
functional
interface on both
left and right sides
without flat support
Product appearance
Doorbell
02

Volume
plus
Volume
reduction
Pairing
selection
Pairing
Indicator
light
Speaker
Micro-USB port
Chime
03

Quick Start
Android
Download
Download
App Store
Download and install the app
Adding the doorbell
The smart doorbell supports both wireless battery
power supply and wired powersupply.
The doorbell can be connected and operated via smart
phones running on both Android and iOS platforms. For your
best experience, please scan the QR code below, download
and install the App and follow the instructions to complete
user registration.
Login to the app and follow the instructions to connect
Wi-Fi and add the doorbell (please keep the doorbell close
to the router when it is configured).
Scan the QR code or go to the link to download
and install the app:
https://www.cyberviewplus.com/download/
04

05
Connecting the chime
1) Connecting the doorbell chime with a charger
The power button can control the doorbell on/o function
or enter the network configuration mode. You need to first
remove the doorbell from the bracket before the button can
be pressed.
Connect the doorbell chime to the power supply of 5V/1A~
5V/2A, and the doorbell chime will ring once.
2) Bringing your doorbell close to the chime
Move the doorbell within 2 meters of the doorbell Chime, so
that the doorbell and the doorbell chime can be paired
stably.
Power on/o and
network configuration
Installation and use of the device
must be in strict accordance with
your local electrical safety regulations.
Use a UL certified power supply
that meets LPS requirements if
an adapter is used.
Use the recommended cordset
(power cord) in accordance with
the specified ratings.
DC-5 V
Power button
< 2m/7ft

06
3) Putting the doorbell chime into sync state
Press and hold the "SYNC" button on the side of the doorbell
chime until the indicator light flashes.
4) Synchronizing the doorbell with the chime
Press and hold the doorbell button for 6 seconds, the
doorbell will ring twice, send a connection signal, and the
doorbell chime will ring.
5) Connection Successful
Press the doorbell button for testing. When a chime rings, it
indicates that the connection is successful.

07
Doorbell binding
1) Click the "Add Now" button in the app, press and hold the
doorbell switch button for 3 seconds to turn on the
doorbell, and the app will automatically search for devices
that are on and not bound. Select the device you want to
bind in the search results for the next step.
2) For users who need to be shared with, click "+" on the
homepage and select "Add Friend's Device" to enter the
scan code page.
To ensure a long-distance connection, the doorbell only
supports a 2.4 GHz Wi-Fi network with stronger wall
penetration capability and does not support Wi-Fi with
enterprise-level authentication. Please make sure that
your Wi-Fi meets the requirements.
3) After a while, the doorbell will play a sound indicating that
the connection is successful. At this point, please set a
name for the doorbell on the app and select the location
where you want to place the doorbell. Click Finish to
complete the pairing.

08
Doorbell sharing
You can use this feature when you need to use the doorbell
with other family members or friends. Only the admin user
who has bound the doorbell for the first time can share and
set up the doorbell, while other members can only view the
live video or video playback feature of the doorbell.
1) For admin user of the doorbell, find the doorbell you wish
to share on the app homepage or doorbell settings screen,
then click the share button and enter the Share page. Click
"Device Sharing" to generate a shared QR code.
Possible problems with binding:
When you hear the "Password error", please check
whether the Wi-Fi password you entered in the App is
correct.
When you hear the "Authentication method error", please
make sure that your Wi-Fi network is not in an
enterprise-level network connection mode, as the
doorbell only supports networks with a security level
below WPA-2.
When you hear the "AP does not exist", please check if you
have selected or entered the correct Wi-Fi name. Please
place the doorbell near the Wi-Fi router and make sure the
router is powered on. Also, please note that 5 GHz Wi-Fi
cannot be searched by the doorbell either.
When you hear the "IP acquisition timeout", it means that
you have too many devices connected to the router and to
connect more devices, please delete some infrequently
used devices or reboot the router to clear the unconnected
doorbell whose lease has expired, and you may need to
contact the router administrator.
When you hear the "Server connection failed", please
check if your router is properly connected to the external
network. This is usually the case when your home network
is disconnected or the router you choose is a server on the
LAN. Please make sure the network connection is normal,
and try to connect again by temporarily turning o the
firewall.

09
3) After the shared user
successfully scans the QR
code on the admin user's
mobile phone, the admin
user will receive a
confirmation notification,
then click "Accept" to
complete the doorbell
sharing.
2) For users who need to be shared with, click "+" on the
homepage and select "Add Friend's Device" to enter the scan
code page.
Installation
Your doorbell comes with a built-in
battery pack, and it also works with
the existing 8V~24V AC hardwire
power source. It enables you to
make use of your legacy doorbell
wiring for retrofitting installation.
Retrofitting installation (optional)
To replace your existing doorbell, please follow below
installation steps:
1) Shut o the master circuit breaker in your house.
Failure to turn o your power might result in serious
injury.
Use a multimeter to test the voltage.
Check if the voltage is printed on the
transformer that supplies power to
your existing doorbell.

10
Determine the mounting position of the doorbell. Check if
you can reuse the existing holes on the wall, if you don't
want to drill new holes to mount your video doorbell.
It is suggested to mount the doorbell at least 4 feet (120 cm)
above the ground for the optimal angle of view and best
motion detection performance.
2) Select a location for your video doorbell.
The doorbell, indoor unit, and router need to be as close as possible
(to avoid networking failure due to distance).
The doorbell should be installed on non-metallic porches and
walls (to avoid signal shielding) or axed to the wall on the door side.
4 feet
(120cm)

11
3) If installing on stucco, brick, or concrete, mark 2 drill
holes using the doorbell bracket as a template. Then, use a
1/4” masonry drill bit to drill holes in your wall, and insert
the included anchors. (If you’re installing on a wood surface,
skip this step.)
Smart Video
Doorbell
Mounting
order
doorbell
bracket

12
1) Release the bracket from the doorbell with the provided
tool.
2) Mark the screw holes and mount the bracket on your wall
with screws.
Wireless installation
wall mount
screw kit

13
3) Adhesive tape is provided to mount the bracket on flat
surfaces. (Optional）
5) All set! Press the doorbell button to run a test.
4) Attach the doorbell to the fixed mounting bracket.
When mounting the doorbell with 3M adhesive pad, in
order to improve the adhesive pad's adhesive eect,
please wipe the mounting location to ensure that there is
no dirt and dust. when the 3M adhesive pad is attached
to the wall, you need to press evenly up and down to
ensure that the adhesive pad is fully activated.
UP

14
You can purchase the following angled brackets to point
your doorbell to a specific view angle.
Install at an angle (optional)
Charging your doorbell
corner mount
(optional)
wedge mount
(optional)
20 degree angle
10 degree stackable
wedge mount unit
Compatible charger not included
USB compatible mobile phone
charger (DC 5V 1A~2A)
Before the doorbell installation, please charge your doorbell.
During the charging process, the yellow indicator light of the
doorbell is always on, and then
it will become solid green when
the charging is completed. It
may take about 10 hours to fully
charge the doorbell.

15
Installation steps
1) If you have an exsiting doorbell, please remove it
2) Mark the screw holes and mount the angle bracket on
your wall with screws.
3) Mark the screw holes and
mount the plane bracketon the
angle bracket with screws.
4) After fixing the screws, the
installation is completed.

16
You can also enable the anti-theft alarm in doorbell settings.
Detach and alarm
1) Anti-theft Tamper Alarm
Product specifications
LED indicator explanation
With the tamper alarm on, your doorbell detects dismounting
activities with the magnet on its back, and then a 30-second
siren alarm will be triggered. Meanwhile, video recording will
start, and an alarm notification will
be pushed to the owner’s app
account.
2) Tamper Alarm On
You can disable the tamper alarm in
doorbell settings, and detach the
doorbell without triggering any alarm
for battery recharge or regular
maintenance.
3) Tamper Alarm O
Working mode
Sleep mode
Charging mode
Charging completed
Network setup mode
Solid blue light
O
Solid yellow light
Solid green light
Flashing blue light
Mode Status

17
Power port
Ringtone type
Number of ringtones
Communication
Adapter requirements
Dimension
Micro USB
Chord music
5 ringtones (optional)
FSK
5V/1A or 1.5A
65×65×20 (mm)
Item Specification
Camera
View angle
Image resolution
Video bitrate
Storage medium
Battery capacity
Adapter requirement
Dimension
2K Camera
114° horizontal, 82° vertical
2048(H) x 1536(V)
Adaptive
Micro SD card (up to 128 GB)
5200 mAh
5V/1.5A
144×46×31 (mm)
Item Specification
Video doorbell specifications
Wireless chime specifications

18
Firmware upgrade
When you connect your camera through the App, it will prompt
you if the latest firmware is available. You can also manually
check the firmware upgrade in the settings of the App.
FCC warning
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference.
(2) this device must accept any interference received, including
interference that may cause undesired operation. Any changes
or modifications not expressly approved by the party responsi-
ble for compliance could void the user's authority to operate
the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
Please make sure that your camera is fully charged or
connected to the power adapter before upgrading the
firmware, please do not cut o the power supply duringthe
upgrading

19
To maintain compliance with FCC’ s RF Exposure guidelines,
this equipment should be installed and operated with
minimum distance between 20cm the radiator your body:
Use only the supplied antenna.
FAQ and troubleshooting
A: It has built-in infrared light beads. Only a faint red light
can be seen under the night vision mode, and the camera is
still clear in a dark environment.
Q: Does the doorbell glow red when using its night vision?
A: Please use a 2.4 GHz wireless network. The doorbell does
not support the 5 GHz wireless network. Meanwhile, please
set the Wi-Fi authentication method to a security method
below wpa2-psk, which requires a password.
Q: What are the requirements for Wi-Fi?
A: Click the icon on the top left corner of the "Library"
screen to set filtering conditions, check the conditions and
save them to quickly review the video playback by category.
Q: How can I review videos in a quick and categorized
way?
A: After taking the doorbell o the bracket, press and hold
the power button for 3 seconds to reboot it. If it doesn't
respond, you can reset the doorbell by poking the reset hole
with a pin.
Q: What should I do when the doorbell acts abnormally?
A: It has been tested that the Wi-Fi connection distance is
up to 150 meters in an open environment. The actual
situation depends on the Wi-Fi signal strength and the
surrounding environment (too thick walls, electromagnetic
wave doorbells, and large metal objects can interfere with
the Wi-Fi signal). If the doorbell connection signal is weak
orunstable, please place the doorbell as close to the router
as possible.
Q: How far away from the router should the doorbell be
placed?