H. Winter WINTER FS-80B User manual

OPERATION MANUAL
SINGLE BELT ROUND ROD SANDER
WINTER FS-80B
WARNING!
The operator must thoroughly read this manual before operation.
Keep this manual for future reference.
Henrik Winter Holztechnik GmbH
Druckereistr. 8
04159 Leipzig
Tel: [phone] Fax: [phone] Funk: +49 (0)171/2820443
Em@il: [e-mail] Internet: www.winter-holztechnik.de

1
HIGH-SPEED ROUNDED
WOOD ROD POLISHING MACHINE
FS-80B
is a precise SINGLE BELT ROUND ROD SANDER. We believe that if you
operate it normally and make a good maintenance on time，the machine
will stay in a perfect condition. Before operating the machine，please read
the instruction carefully.
SPECIFICATIONS
：
TYPE FS-80B
Main Shaft Motor（HP）
3
Vacuum Cleaner Motor
（
HP
）
1
Work area diameter φ5～φ80m/m
Sand Belt 5”x73”
Grinder R.P.M. （m/min）900
Feeding speed 1-20M
Size of machine（cm）
75x75x135
Packing size
（
cm
）
88x85x152
Net weight（kg）250
Exported Packing Weight
（
kg
）
320
FEATURES
：
1、Suitable to the grinding for all kinds of round bar such as lumber
sticks, rattan, metal, acrylic, graphite……etc.
2、Besides the grinding to crude grains, it is suitable to grinding for what
of fine products with spray painting.
The rough and fine grindings can be done at the same time.
It can enhance the operation ability higher.
3、It can be adjusted arbitrarily according to length, diameter and
inclination widely require for grinding.
4、Easy to operate, special technician isn’t required. The machine can
enhance the efficiency of work.

2
OPERATION STEPS
：
1、Put machine in a steady position，and then check whether the power is
suitable to motor voltage. Turn on the electricity supply and examine
whether the revolution of main shaft follows the arrows. If not，turn off the
power and switch the two wire lines.
2、Adjust the working table to a lower or higher position according to the
diameter of material.
3、Change and adjustness of the sand belt：
（1）Press the rod of sand belt in the direction of clockwise 【Fig 1-A】and
then you can change the sand belt. After that, move the adjusting rod back.
Note: After the start of machine, keep away from lifting up the adjusting rod
to prevent danger.
（2）Adjust the screw 【Fig 1-B】for pulling out-in the sand belt. The sand
belt should be aimed at the center of wheel.
A
B
Fig 1
4、The suitable pressure for pressing wheel is to keep the thinkness of
material less than 1M/M.
The adjustment procedure：
Loose the nut【Fig 2-A】and adjust the screw【Fig 2-B】according to the
pressure and then lock nut 【Fig 2-A】.

3
A
B
Fig 2
5、The adjustment of proceeding speed of sand belt：
If you put the pressing wheel right at the center, the speed will turn slow. On
the contrast, the sander the wheel is, the faster the speed occurs.Adjust
the screw according to what you what you need. 【Fig 3-A】
Note: The machine must be turned on, when you adjust it.
A
Fig 3
6、The adjustment of the spring pressure is according to crank of the
materials. The bigger the obliquity is, the heavier pressure becomes.

4
Fig 4
MAINTENANECE:
1、Fill in grease to the oil intake before operation every day.
2、Add the grease to the moving shaft.
During the operation, neither let other things except the materials
needed stay between the working table and sand belt nor use anything
sharp for finding.
3、To clean dust and remains on the machine，after finished daily
operation.
If you need the accessories of sand belt or other ，or other services，you are
welcome to contact our agents near your address. We are glad to be of service
to your satisfaction.
THANK YOU! MAY YOU BE HAPPY WITH YOUR MACHINE!

5
ROD MILLING MACHINE
PART
NO PART NAME Unit QUANTITY
1 Body 1
2 Motor 1
3 Spring washer 14
4 Hexagon Screw 13
5 Kery 1
6 Sand Belt Drum 1
7 Spring washer 1
8 Nut 1
9 Pulley 1
10 Spring washer 2
11 Nut 2
12 Sub Worktable 1
13 Spring washer 8
14 Hexagon Screw 8
15 Hanging Brocket 14
16 Spring washer 1
17 Hexagon Screw 8
18 Round head Screw 10
19 Hanging 2
20 Hexagon Screw 1
21 Spring Seat 1
22 Idel Seat 1
23 Shaft of Seat 1
24 Ball Bearing 4
25 Pulley 1
26 Washer 1
27 Hexagon Screw 7
28 Washer 4
29 Hexagon Screw 4
30 Hanging 1
31 Dust Catcher Motor Packing 1
32 Hexagon Screw 8
33 Dust Catcher Motor 1
34 Hanging 1

6
ROD MILLING MACHINE
PART
NO PART NAME Unit QUANTITY
35 Movable handle 1
36 Hexagon Screw 6
37 Spring washer 6
38 Protection Uses Cover
Bracket 1
39 Setting Rule Brocking 1
40 Hexagon Screw 2
41 W
orkpiece Size Adjusting
Handle 1
42 Nut 6
43 Grease Nipple 2
44 Setting Rule 1
45 Ball Bearing 2
46 Rubber Wheel Guard Bracket 1
47 Pin 1
48 Drive Wheel 1
49 Rubber Wheel Guard 1
50 Snap Ring 1
51 Ball Bearing 2
52 Rubber Wheel 1
53 Rubber Wheel Shaft 1
54 Rubber Wheel Shaft Carriage 1
55
Carriage Shaft of Rubber
Wheel Shaft 1
56 Feed Control Spring 1
57 Worm Gear 1
58 Snap Ring 1
59 Setting Bolt of Worm Gear 1
60 Worm Gear Bracket 1
61 Nut 1
62 Socket Head Screw 2
63 Snap Ring 1
64 Adjusting Worm 1
65 Nut 1

7
ROD MILLING MACHINE
PART
NO PART NAME Unit QUANTITY
66 Movable Handle 1
67 Spring Handle 1
68 Nut 5
69 Handle 1
70 Spring Seat 1
71 Protection Uses Cover
Bracket 1
72 Protection Uses Cover
Bracket 1
73 Drive wheel shaft 1
74 Ball Bearing 1
75 Adjusting Disk of Spring
Loose & Tight 1
76 Pulley 1
77 Hexagon Screw 1
78 Pulley Hanging 1
79 Hexagon Screw 2
80 Spring Handle 1
81 Spring Sleeve 1
82 Feed Wheel Guard Spring 1
83 HangingArm Bracket 1
84 1
85 Hexagon Screw 2
86 Handle 2
87 Spring Seat 1
88 Spring 1
89 Body Handle 1
90 Hexagon Screw 1
91 Pin 1
92 Upper Sand Belt Drum Shaft 1
93 Upper Sand Belt Drum 1
94 Snap Ring 1
95 Hexagon Screw 1

8
ROD MILLING MACHINE
PART
NO PART NAME Unit QUANTITY
96 Crank 1
97 Handle 1
98 Crank Handle 1
99 Spring pin 2
100 Washer 6
101 Pin 1
102 Back Drum Becket 1
103 Ball Bearing 4
104 Sand Belt Back Drum Shaft 2
105 Sand Belt Back Drum 2
106 Socket Head Screw 4
107 Sub Worktable 1
108 Washer 1
109 Hexagon Screw 3
110 Worktable 1
111 Worktable Bracket 2
112 Hanging 1
113 Hanging 1