Haier AD07SL2VH1 User manual

WIRED CONTROLLER Page 1
ENGLISH
Wired Controller
User Manual
TABLE OF CONTENTS
Ductless Split Air Conditioner
Indoor Unit
AD07SL2VH1
AD09SL2VH1
AD12SL2VH1
AD18SL2VH1
AB09SC2VH2
AB12SC2VH2
AB18SC2VH2
AW09ES2VH3
AW12ES2VH3
AW18ES2VH3
AW24ES2VH3
1Ships with indoor unit
2Optional and compatible
3Optional, requires an accessory kit to be
compatible, model number WK-A
Wired Control Panel Functions .................. 2
Features and Interface....................................2
Installation.............................................3-4
Wired Controller Wiring Instructions.........3-4
Dip Switch........................................................4
Operation ..............................................5-8
Settings & Functions...................................5-8
• ThissystemshouldbeinstalledbyaqualiedHVAC
professional.Incorrectinstallationmaycausere,water
damage,personalinjuryordeath.
• Whenabnormalitiessuchasaburntsmellaredetected,
immediatelypowerothemainswitchandcontacta
licensed contractor.
• Do not obstruct or cover ventilation grill on the air con-
ditioner.Donotputngers/objectsintoinlet,outletor
swing louver
• Do not allow children to play on or near the outdoor
system equipment
WARNING
!

Page 2 WIRED CONTROLLER
ENGLISH
User Friendly: Back light; Room temperature display
Functions: Clock;Timer;SleepFunction;HeatReclaim
Ventilation;ECO;FilterCleaning;ErrorCodedisplay;Child
Lock;ParameterInquiry;UnitNO.Setting;StaticPressure
Grade Inquiry; Temp. Compensation setting; Forced
Cooling/Heating
WIRED CONTROL PANEL FUNCTIONS
Wired Controller YR-E17
Features and Interface
Clock;Parametersetting/Inquiry;Malfunction
display
TimerON/OFF;Sleepfunction;Parameter
setting/Inquiry;Malfunctiondisplay
ROOM/SETtemp.andhumiditydisplay,each
step is 0.5°C(1°F).Forexample,ifthetempis
25°C(77°F),itwilldisplay25.°C(77°F).Humidity
display function is reserved.
EnergySavingfunction.Thisiconwillbedis-
played only when energy saving function is set.
Filter Cleaning
Child Lock
Lock/Central
Motion Sensing (Reserved)
Left/RightSwing.Thisiconisdisplayedonly
when in swing function
Up/DownSwing.Thisiconisdisplayedonlywhen
in swing function
Sleep function. This icon is displayed when setting the
sleep function. Remaining sleeping time is displayed in
the top right corner.
ElectricalHeating.Thisiconisdisplayedwhenelectrical
heating is set on DC wired control.
HeatingMode
Fan Mode
Dry Mode
HeatReclaimVentilation.Thisiconisdisplayedwhen
setting the heat reclaim ventilation.
Intelligent Mode--automatic cycling.
Cooling Mode

WIRED CONTROLLER Page 3
ENGLISH
INSTALLATION
1. Put communication wire through the hole in the back cover
as shown.
2.Mountthebackcoverinthedesiredlocation,makingsure
not to pinch the communication wire. Then connect the com-
municationwiretoCON1portofthewiredcontroller.Replace
the cover onto the unit to complete the installation.
Wired Controller Wiring Instructions
Communication Wiring
Step By Step Guide To Slim Duct Unit Installation
There are three methods to connect the wired controller to
the indoor units.
Communication Wiring
Length
Dimension of Wiring
0~100 ft (0~30m) 22AWG(0.3mm2)x3-core
shielded wire
100~200 ft (30~60m) 20AWG(0.5mm2)x3-core
shielded wire
200~300 ft (0~90m) 18AWG(0.75mm2)x3-core
shielded wire
300-400 ft (90~120m) 16AWG(1.25mm2)x3-core
shielded wire
400~500 ft (120~150m) 14AWG(2mm2)x3-core
shielded wire
A.Onewiredcontrollercontrolsoneindoorunit;theindoor
unit connects with the wired controller through a 3 conductor
shielded cable.
C. Two wired controllers control one indoor unit. The wired
controller that connects with the indoor unit is called the
mastercontroller,theotheriscalledtheslavecontroller.The
master wired controller and the indoor unit (as well as the
master controller and the slave controller) are all connected
through 3 conductor shielded cables.
A
B.Onewiredcontrollercancontrolupto16setsofindoor
units(max);A3conductorshieldedcablemustconnect
the wired controller and the master unit (the indoor unit
connected to the wire controller directly). The others connect
to the master unit through a 2 conductor shielded cable.
B

Page 4 WIRED CONTROLLER
ENGLISH
Dip Switch
Wired Controller Wiring Instructions
INSTALLATION
Dimensions
Unit: inch (mm)
Dip Switch ON/OFF Function Default Setting
SW1-1 ON Set as the slave controller OFF
OFF Set as the master controller
SW1-2 ON Ambienttemp.displayavailable OFF
OFF Ambienttemp.displayunavailable
SW1-3 ON Display ambient temp. from PCB of indoor OFF
OFF Display ambient Temp. from wired controller
SW1-4 ON Auto-restartinvalid OFF
OFF Auto-restartvalid
SW1-5 ON Fahrenheit OFF
OFF Celsius
SW1-6 ON Swingangleadjustmentavailable OFF
OFF Swingangleadjustmentunavailable
SW1-7 ON Up/DownandLeft/Rightswing OFF
OFF Up/Downswing
SW1-8 ON FreshAirunit OFF
OFF General unit

WIRED CONTROLLER Page 5
ENGLISH
OPERATION
1
2
3
NOTE: This function requires the ON/OFF key LED to be
turned OFF and the screen backlight to be illuminated.
PressandholdtheMODEkeyfor5seconds,thenumberof
the mode currently being used will display in the upper left
corner of the screen. (Default is 0) Press the pq keys to
changetoonethedierentmodesavailable:0,1,2,or3.
PressSETtoconrmthesetting.
NOTE:Correspondingmodes
0–[Intelligent][Cooling][Heating][Fan][Dry]
1–[Cooling][Heating][Fan][Dry]
2 – [Cooling] [Fan] [Dry]
3–[Cooling][Heating][Fan][Dry](sameas1)
Note: This function requires the ON/OFF key LED to be
turned OFF and the screen backlight to be illuminated.
PressandholdtheTIMEkeyfor10seconds.Theunitnumber
will display in the upper left corner of the screen. The error
code/historicalerrorcodewilldisplayintheupperrightcorner
of the screen. Press pq keys to select the unit number to
viewitserrorcodes.UnderErrorCodedisplayscreen,press
andholdtheTIMEkeyfor5secondstoclearthefaultcodesof
all the units.
PresstheMODE,FAN,TIME,SET,orON/OFFkeytoexitthe
function.Ifnokeyispressedin10seconds,thefunction
will also exit. If there are no current errors or historical error
codes,“--”willbedisplayed.
The wired controller will
momentarily display
all display icons upon
powering up or when
resetting the system.
During the initialization
process,thecontroller
willdisplay,ina
repeating order:
88:88 (upper left
corner),88:88(upper
right corner) 88.8
(main temperature).
This cycle keeps repeating until initialization is complete.
ThegreenON/OFFLEDwillalsoashcontinuouslyuntil
initialization is complete.
If the wired controller is unable to communicate with the
indoorunitPCBafterpoweringon,initializationwillterminate
in 4 minutes. The communication malfunction can be checked
using the malfunction inquiry function. (See Malfunction
Display)
Initialization
Mode Setting
Error Code Display
Settings & Functions
1.Theclockisdisplayedin24Hourtime
A.ItcannotbesetforAM/PM.
B.TheclockfunctioncannotbesetwhenSLEEP
function or a timer function is currently set.
Whenthesystemisrstpoweredup,afterinitialization,the
clock will default to 12:00. Within 10 seconds of the clock be-
ingdisplayed,thetimecanbeset.Theclockiconandminutes
portionofthetimedisplaywillbeashing.Pressthepq keys
toadjusttheminutes.(Pressingandholdingthepq keys will
acceleratethetimeadjustment.)Withtheminutesset,press
theTIMEkey.Theclockiconandhoursportionofthetime
displaywillnowbeginashing.Pressthepqkeystoadjust
thehours.PresstheSETkeytoconrmthesetting.
To set the clock after initial power up or reset time has ex-
pired,pressandholdtheTIMEkeyfor5seconds.Theclock
iconandminutesportionofthetimedisplaywillbeginash-
ing. Press the pqkeystoadjusttheminutes.Withthemin-
utesset,presstheTIMEkey.Theclockiconandhoursportion
ofthetimedisplaywillnowbeginashing.Pressthepq keys
toadjustthehours.PresstheSETkeytoconrmthesetting.
If neither pqkeyispressedwithin10seconds,orifthe
MODE,FAN,orON/OFFkeysarepressedpriortopressingthe
SETkey,thesettingfunctioniscanceledandthetimereverts
back to the previous setting.
Withthesystemturnedo,taptheTIMEkeytoactivatethe
screen backlight (if not already lit).
1.PressandholdtheTIMEandqkeys for 5 seconds to set the
backlight“on”time.Thesettimewillbedisplayedintheupper
right corner of the screen.
2. Press the pqkeystoadjustthetime.Settimesavailable
are:0seconds(backlightalwayson),15seconds,30seconds,
and 60 seconds. Initial default time is 15 seconds.
3.Withtimeselectionmade,presstheSETkeytoconrmthe
setting.
If neither pqkeyispressedwithin10seconds,orifthe
MODE,FAN,orON/OFFkeysarepressedpriortopressingthe
SETkey,thesettingfunctioniscanceledandrevertsbackto
the previous setting.
ToswitchfromCelsiustoFahrenheit,selectthemodeyou
wishtooperate(COOL,HEAT,DRY,INTELLIGENT/AUTO).
Press and hold the pkey to reach 30 °C then continue holding
the pkey for 15 seconds until the display reads 86 °F. Use the
pqkeystoadjusttodesiredtemperature.
ToswitchfromFahrenheittoCelsius,selectthemodeyou
wishtooperate(COOL,HEAT,DRY,INTELLIGENT/AUTO).
Press and hold the qkey to reach 60 °F then continue holding
the qkey for 15 seconds until the display reads 16 °C. Use the
pqkeystoadjusttodesiredtemperature.
Switching between Fahrenheit & Celsius
Clock Function
Screen Saving

Page 6 WIRED CONTROLLER
ENGLISH
NOTE: The display backlight must be illumi-
nated before proceeding. To turn the back-
light on, press any key (MODE, FAN, pq,
TIME, or SET) located at the bottom of the
display, or press the ON/OFF key located at
the top of the display.
Timer ON
PresstheTIMERkeyonce,theONtimericonwillappearinthe
upperrightcornerofthescreen.TheONiconandhourpo-
sitionareashing.Pressthepq keys to set the hour. Press
theTIMERkeyagain,theONiconandminutespositionare
nowashing.Pressthepq keys to set the minutes. Press the
SETkeytoconrmthesetting.
Timer OFF
PresstheTIMERkey3times,theOFFtimericonwillappearin
theupperrightcornerofthescreen.TheOFFiconandhour
positionareashing.Pressthepq keys to set the hour.
PresstheTIMERkeyagain,theOFFiconandminutesposition
arenowashing.Pressthepq keys to set the minutes. Press
theSETkeytoconrmthesetting.
Timer ON/OFF
PresstheTIMERkey5times,theON/OFFtimericonwillap-
pearintheupperrightcornerofthescreen.TheONiconand
hourpositionareashing.Pressthepq keys to set the hour.
PresstheTIMERkeyagain,theONiconandminutesposition
arenowashing.Pressthepq keys to set the minutes. Press
theTIMERkeyagain,theOFFiconandhourpositionarenow
ashing.Pressthepqkeystosetthehour.PresstheTIMER
keyagain,theOFFiconandminutespositionarenowashing.
Press the pqkeystosettheminutes.PresstheSETkeyto
conrmthesetting.Basedonthetimesset,theindoorunit
willdeterminewhicheventhappensrst(ON-OFForOFF-
ON)andadjuststhearrowdirectionaccordingly.
If neither pqkeyispressedwithin10seconds,orifthe
MODE,FAN,orON/OFFkeysarepressedpriortopressingthe
SETkey,thesettingfunctioniscanceledandrevertsbackto
the previous setting.
Timer Cancel
PresstheTIMEkeyupto9timestocyclethroughthetimer
settings.Whenthetimericondisappears,thetimerfunctionis
canceled.
Note:Anactivetimerfunctionwillremaindisplayedonscreen
until the set time has been reached and command completed.
Timer Function Setting
OPERATION
Settings & Functions
PresstheSETkey.Theswinglouverfunctioniconwill
be displayed. Press the pq keys to advance through
thefunctionstoselectECOfunction.(Theiconwill
beashing)PresstheSETkeytoconrmthesetting.TheECO
icon will remain on.
TocancelECOfunction,repeattheabovesteps.
NOTE:Theenergysavingdefaultparametersarelistedbelow:
74°F Lowest temperature limit of Cooling and Dry mode.
78°FHighesttemperaturelimitofHeatingmode.
74°F–86°FTemperatureadjustmentrangeinCoolingandDry
mode.
60°F–78°FTemperatureadjustmentrangeinHeatingmode.
ECO
For Cooling
UnderCoolingmode,setthetemperatureto86°F.Pressand
holdtheFANkeyfor5seconds.TheCoolingECOparame-
ter(ashing)willbedisplayedintheupperleftcornerofthe
screen. Default temperature is 74°F. Press the pq keys to
adjustthelowesttargetcoolingtemperature.PresstheSET
keytoconrmthesettingandexitsetup.
For Heating
UnderHeatingmode,setthetemperatureto60°F.Pressand
holdtheFANkeyfor5seconds.TheHeatingECOparameter
(ashing)willbedisplayedintheupperrightcornerofthe
screen. Default temperature is 78°F. Press the pq keys to
adjustthehighesttargetheatingtemperature.PresstheSET
keytoconrmthesettingandexitsetup.
PressandholdtheSETandFANkeysfor5seconds.Thecur-
rent static pressure will be displayed in the upper right corner
ofthescreenandthe“StaticPressure”iconwillbegintoash.
PresstheTIMEkeytoshifttheunitno.displayedintheupper
left corner of the screen. The unit numbers are from 00-15.
Press the pqkeystochangethestaticpressuregrade,
shown in the upper right corner of the screen.
Numberrangeis01-04.PresstheSETkeytoconrmthe
setting.PresstheMODE,FAN,orON/OFFkeytoexitthe
function.Ifnokeyispressedin10seconds,thefunctionwill
also exit.
NOTE: This function requires the ON/OFF key LED to be
turned ON and the screen backlight to be illuminated.
NOTE: This function requires the ON/OFF key LED to be
turned ON and the screen backlight to be illuminated.
NOTE: This function requires the ON/OFF key LED to be
turned ON and the screen backlight to be illuminated.
ECO Energy Saving Function
ECO Parameter Setting
Static Pressure Grade Inquiry & Adjustment

WIRED CONTROLLER Page 7
ENGLISH
OPERATION
NOTE: This function requires the screen backlight to be
illuminated. The ON/OFF key LED can be either On or O.
PressandholdtheSETkeyfor10seconds.Thewiredcontrol-
ler address and communication address between the indoor
and outdoor unit are displayed in the upper left corner of the
screen. The central address is displayed in the upper right
corner of the screen.
Press the pq keys to select the indoor unit number: 0 - 3F.
PresstheSETkeytoconrmthesetting.PresstheMODE,
FAN,orON/OFFkeytoexitthefunction.Ifnokeyispressedin
10seconds,thefunctionwillalsoexit.
NOTE: This function requires the screen backlight to be
illuminated. The ON/OFF key LED can be either On or O.
PressandholdtheSETkeyfor5seconds.Theunitnumber
will be displayed in the upper left corner of the screen. The
data type and current data will be displayed in the upper right
corner of the screen.
Press the pq keys to scroll through the data types. (See
chartfordatatype/currentdata)
PresstheMODE,FAN,SET,orON/OFFkeytoexitthefunc-
tion.Ifnokeyispressedin10seconds,thefunctionwillalso
exit.
NOTE: This function requires the screen back-
light to be illuminated. The ON/OFF key LED can
be either On or O.
Child Lock can be used to prevent unintended
operation of the control unit.
1.PressSETandtheqkeys together for 5 seconds to
activate the Child Lock function. The child lock icon will be
displayedontheleftsideofthescreen.Allnormalfunctionsof
the keys will be disabled.
2.TounlocktheChildLockfunction,presstheSETkeyand
the qarrow together for 5 seconds. The child lock icon will
disappearfromthescreen.Allnormalfunctionsofthekeys
will be restored.
Note: This function requires the ON/OFF key LED to be
turned OFF and the screen backlight to be illuminated.
PressandholdtheFANkeysfor5seconds,thecurrent
temperature compensation value is displayed in the upper
right corner of the screen. (The default value is 00). Press the
pq keys to change the temperature compensation value.
Theadjustmentrangeis-07°Fto+07°F.PresstheSETkeyto
conrmthesetting.PresstheMODE,FAN,TIME,orON/OFF
keytoexitthefunction.Ifnokeyispressedin10seconds,the
function will also exit.
NOTE:Thecompensationvalueisusedforambienttempera-
ture and is valid only for the wired controller sensor.
The swing function deter-
mines air circulation.
1.PressSETkeytoaccess
Swing function circulation.
2. Use pqkeys to select
desired swing function.
If SW7ison,airwillcirculate
UP/DOWN/LEFT/RIGHT.
3.PressSETkeytoconrm
swing function selection.
Left/Right/Up/Down Swing
Note: This function requires the ON/OFF key LED to be
turned OFF and the screen backlight to be illuminated.
Forced Cooling
Whenthesystemisturnedoincoolingmode,pressandhold
theON/OFFkeyfor10seconds.Thesystemwillenterforced
cooling.Thetemperaturedisplaywilldisplayaashing“LL”.
PresstheON/OFFkeytoexitforcedcoolingmode.
Forced Heating
Whenthesystemisturnedoinheatingmode,pressandhold
theON/OFFkeyfor10seconds.Thesystemwillenterforced
heating.Thetemperaturedisplaywilldisplayaashing“HH”.
PresstheON/OFFkeytoexitforcedheatingmode.
NOTE:Wheninforcedcoolingorheating,allkeysaredisabled
exceptfortheON/OFFkey.
Forced Cooling/Heating
Parameter Inquiry
Child Lock Function
Temperature Compensation Setting
Unit Number Setting
Settings & Functions

Page 8 WIRED CONTROLLER
ENGLISH
PresstheSETkey.Theswinglouverfunctionicon
will be displayed. Press the pq keys to advance
throughthefunctionstoselecttheSLEEPfunc-
tion.TheSleepandSleep“o”timeiconswillbe
displayed.(TheSleepiconwillbeashing)PresstheTIMEkey,
the“o”iconwillbegintoash.Pressthepq keys to set the
“o”time.(Timerangeis0.5hto72h)PresstheSETkeyto
conrmthesetting.TheSleepfunctionand“o”timeicons
will remain on.
If neither pqkeyispressedwithin10seconds,orifthe
MODE,FAN,orON/OFFkeysarepressedpriortopressingthe
SETkey,thesettingfunctioniscanceledandrevertsbackto
the previous setting.
TocanceltheSleepfunction.PresstheSETkey.Theswing
louver function icon will be displayed. Press the pq keys to
advancethroughthefunctionstoselecttheSLEEPfunction.
TheSleepandSleep“o”timeiconswillbedisplayed.(The
Sleepiconwillbeashing)PresstheSETkeytocancelthe
function.
NOTE: This function requires the ON/OFF key LED to be
turned ON and the screen backlight to be illuminated.
Sleep Function
TheFilterCleaningiconwillstartashingwhen
the indoor unit has reached 500 hours of operat-
ing time.
Aftercleaningorreplacingthelter,presstheSETkeytoclear
the icon and reset the operating time.
NOTE: This function requires the ON/OFF key LED to be
turned ON and the screen backlight to be illuminated.
Filter Cleaning
OPERATION
Settings & Functions
PresstheSETkey.Theswinglouverfunctionicon
will be displayed. Press the pq keys to advance
throughthefunctionstoselecttheHeatReclaim
Ventilationfunction.(Theiconwillbeashing)
PresstheSETkeytoconrmthesetting.
TocanceltheHeatReclaimVentilationfunction,repeatthe
above steps.
If neither pqkeyispressedwithin10seconds,orifthe
MODE,FAN,orON/OFFkeysarepressedpriortopressingthe
SETkey,thesettingfunctioniscanceledandrevertsbackto
the previous setting.
This function is reserved for future models.
NOTE: This function requires the ON/OFF key LED to be
turned ON and the screen backlight to be illuminated.
Heat Reclaim Ventilation
Note: These functions require the ON/OFF key LED to be
turned OFF and the screen backlight to be illuminated.
Auto Restart
Setting DIP switch SW1-4 located on the PCB of the wired
controltothe“on”positionwilldisabletheautorestartfunc-
tion.Whentheswitchisinthe“o”position,auto-restart
isenabled(defaultposition).Whentheswitchisinthe“on”
position,auto-restartisdisabled.
Informationretainedinauto-restartare:Mode,FanSpeed,
TemperatureSetting,SwingState,andHeatReclaimVentila-
tion function.
Communication Error of Wired Controller
If there is no communication between the wired controller and
indoorunitfor4minutes,whencheckingerrorcodes,“07”will
be displayed in the upper right corner of the display.
Other Functions

www.Haier.com
HaierAmerica,
Wayne,NJ07470
©2015HaierAmericaTrading,LLC.
Model#:YR-E17
Issued Date: May 2015