Haier HT18TS45SW User manual

Frost-Free Top Mount
Refrigerator / Freezer
Réfrigérateur/congélateur sans
givre à compartiments superposés
Refrigerador/congelador sin
escarcha, de puertas horizontales
User Manual
Guide de l’Utilisateur
Manual del Usuario
Model HT SERIES
Design may vary by model number.
La conguration peut varier selon le numéro de modèle.
El diseño puede variar conforme al número de modelo.

ENGLISH
TABLE OF CONTENTS
PRODUCT REGISTRATION
Thank you for purchasing our Haier
product. This easy-to-use manual will guide you in
getting the best use of your product.
Remember to record the model and serial numbers.
They are on a label inside of the Product.
Model number
Serial number
Date of purchase
Staple your receipt to your manual. You will need it to obtain warranty service.
SAFETY INFORMATION
Important Safety Instructions ......................................................................................................................2
SET UP & USE
Electrical Requirements ................................................................................................................................4
Installation Guide.......................................................................................................................................4-5
Instructions for Unpacking............................................................................................................................5
Installing Your Refrigerator............................................................................................................................6
Parts-Included................................................................................................................................................6
Accessories....................................................................................................................................................6
Parts & Features.............................................................................................................................................7
Door Handle Installation............................................................................................................................8-9
Reversing the Door............................................................................................................................... 10-12
Features and Use ........................................................................................................................................ 12
Operation Instructions......................................................................................................................... 13-15
Food Storage Information.......................................................................................................................... 16
CLEANING AND CARE
Proper Care and Maintenance.............................................................................................................. 17-18
TROUBLE SHOOTING & WARRANTY
Normal Operating Sounds.......................................................................................................................... 19
Troubleshooting.................................................................................................................................... 20-21
Customer Service ....................................................................................................................................... 22
Limited Warranty ........................................................................................................................................ 23

NOTE: If the refrigerator has been placed in a horizontal or tilted position for any period of time, wait 24
hours before plugging the unit in.
1) Use this appliance only for its intended purpose as described in this use and care guide.
2) This refrigerator must be properly installed in accordance with the installation instructions before it is
used. See Electrical Requirements in the Set Up & Use section.
3) This refrigerator should not be recessed or built-in an enclosed cabinet. It is designed for freestanding
installation only.
4) Never unplug your refrigerator by pulling on the power cord. Always grasp the plug firmly and pull
straight out from the outlet.
5) Repair or replace immediately, all electric service cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks or abrasion damage along its length, the plug or the
connector end.
6) If your old refrigerator is not being used, we recommend that you remove the doors. This will reduce
the possibility of danger to children.
7) Do not refreeze foods, that have been thawed completely. The United States Department of
Agriculture in Home and Garden Bulletin No. 69 reads:
"…You may safely refreeze frozen foods that have thawed if they still contain ice crystals or if they are
still cold-below 40°F."
"…Thawed ground meats, poultry, or fish that have any off-odor or off color should not be refrozen
and should not be eaten. Thawed ice cream should be discarded. If the odor or color of any food is
poor or questionable, discard it. The food may be dangerous to eat."
"…Even partial thawing and re-freezing reduce the eating quality of foods, particularly fruits,
vegetables, and prepared foods. The eating quality of red meats is affected less than that of many
other foods. Use refrozen foods as soon as possible to save as much of their eating quality as you
can."
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE:
WHEN USING THIS APPLIANCE, ALWAYS EXERCISE BASIC SAFETY
PRECAUTIONS, INCLUDING THE FOLLOWING:
WARNING
AFTER YOUR REFRIGERATOR IS IN OPERATION, DO NOT TOUCH THE COLD
SURFACES IN THE FREEZER COMPARTMENT, PARTICULARLY WHEN HANDS ARE
DAMP OR WET. SKIN MAY ADHERE TO THESE EXTREMELY COLD SURFACES.
WARNING
PAGE 2 • SAFETY INFORMATION
ENGLISH

8) Do not use any electrical device or any sharp instrument in defrosting your refrigerator.
9) Unplug your refrigerator before cleaning or before making any repairs.
NOTE: If for any reason this product requires service, we strongly recommend that a certified
technician perform service.
10) Do not operate your refrigerator in the presence of explosive fumes.
SAVE THESE INSTRUCTIONS
RISK OF CHILD ENTRAPMENT. BEFORE YOU THROW AWAY YOUR OLD
REFRIGERATOR OR FREEZER, TAKE OFF THE DOORS. LEAVE THE SHELVES IN
PLACE SO THAT CHILDREN MAY NOT EASILY CLIMB INSIDE.
DANGER
PAGE 3 • SAFETY INFORMATION
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS CONT.

ELECTRICAL REQUIREMENTS
INSTALLATION GUIDE
PAGE 4 • SET UP & USE
ENGLISH
GROUNDING INSTRUCTIONS
• Make sure there is a suitable power outlet. 115 Volts, 15 Amps, 3 Prong (Grounded) power outlet with
proper grounding to power the refrigerator.
• Avoid the use of three prong adapters or cutting off the third grounding prong in order to
accommodate a two prong outlet. This is a dangerous practice since it provides no effective grounding
for the refrigerator and may result in shock hazard.
USE OF EXTENSION CORDS
• Avoid the use of an extension cord because of potential safety hazards under certain conditions.
If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade
grounding plug and a 3-slot outlet that will accept the plug. The marked rating of the extension cord
must be equal to or greater than the electrical rating of the appliance. DO NOT USE EXTENSION
CORD LONGER THAN 12 FT.
INSTALLATION LIMITATIONS
• Select a suitable location for the refrigerator on a hard even surface away from direct sunlight or heat
source, e.g. radiators, baseboard heaters, cooking appliances, etc. Any floor unevenness should be
corrected with the leveling legs located on the front bottom corners of the refrigerator.
UNPACKING YOUR REFRIGERATOR
1. Remove all packaging material. This includes the corrugated base and all adhesive tape holding the
refrigerator accessories inside and outside.
2. Inspect and remove any remains of packing, tape or printed materials before powering on the
refrigerator.
NOTE: If your refrigerator comes with a snack pan, remove the blue adhesive tape from the rear of the
pan. The pan will not slide in and out without removing the tape.
USE OF EXTENSION CORDS- POTENTIAL SAFETY HAZARD
WARNING
ELECTRICAL REQUIREMENT - SHOCK HAZARD
WARNING

LEVELING YOUR REFRIGERATOR
• Your refrigerator has two leveling legs that are located in the front bottom corners of your refrigerator.
After properly placing your refrigerator in its final position, you can level your refrigerator.
• Leveling legs can be adjusted by turning them counterclockwise to raise your refrigerator or by turning
them clockwise to lower your refrigerator. The refrigerator door will close easier when the leveling legs
are extended.
PROPER AIR CIRCULATION
• To ensure your refrigerator works at the maximum efficiency it was designed for, you should install it in
a location where there is proper air circulation, plumbing and electrical connections. Your refrigerator
is not designed to operate in temperatures below 55˚F (12˚C ) or above 95˚F (35˚C).
• Do not install your refrigerator in any location not properly insulated or heated, e.g. garage, etc.
Keep out of direct sunlight and away from heating sources such as radiators, heaters, and cooking
appliances.
• The following are recommended clearances around the refrigerator:
Sides……………1” (25 mm) Top....................1" (25 mm) Back..................2" (50mm)
ENGLISH
PAGE 5 • SET UP & USE
INSTALLATION GUIDE CONT.
INSTRUCTIONS FOR UNPACKING
FRONT GRILLE
Your refrigerator comes with a front grille (toe kick), which is reversible based on which side of the
refrigerator the hinges are mounted on. To install the front grille, locate the non-hinge end using the
diagram below and follow the instructions below.
1. Snap the non-hinge side into the air flow opening on the lower rail of the refrigerator.
2. Then, snap the hinge side into the opposite air flow opening in the lower rail beside the bottom hinge.
LOWER RAISE
Non-hinge side Hinge side
Non-hinge side
Hinge side

PAGE 6 • SET UP & USE
ENGLISH
PARTS-INCLUDED
ACCESSORIES
INSTALLING YOUR REFRIGERATOR
TOOLS NEEDED FOR INSTALLATION
5/16 and 3/8 Wrenches or Adjustable WrenchPhillips Screwdriver Putty Knife
DO NOT USE POWER TOOLS TO INSTALL DOOR HANDLES! OVERTIGHTENING THE SCREWS COULD
STRIP THE THREADS!
For non-stainless steel models
that come with a handle
mounting screw factory installed
on the faces of the doors, the
parts-included bag will consist
of:
• 2 Handles
• 1 Front Grille
• 4 Handle attachment screws
• 1 Extra Haier logo badge
• 1 Color-matched screw-plug
• Owner’s manual
For models that don’t come with
a handle mounting screw factory
installed on the faces of the
door, the parts-included bag will
consist of:
• 2 Handles
• 1 Front Grille
• 2 Door face mounting screws
• 4 Door edge mounting screw
• 1 Extra Haier logo badge
• 1 White screw-plug
• Owner’s manual
• 2 Handle cover/trim pieces
For stainless steel models, the
parts-included bag will consist
of:
• 2 Handles
• 1 Front Grille
• 4 Handle attachment screws
• Owner’s manual
The following accessories are available:
• Ice maker Kit HI5MK
• Wire Shelf for Freezer Compartment
• Replacement Light Bulbs
To order accessories, call 1-877-337-3639 or visit us at www.haieramerica.com/support
PARTS-INCLUDED BAG MAY DIFFER BASED ON UNIT PURCHASED.

ENGLISH
PAGE 7 • SET UP & USE
PARTS & FEATURES
Diagram for instructional purposes only.
Design may vary by model number.
Leveling Legs
Front Grille
Crisper Bins
Crisper
Humidity
Controls
Full-Width
Shelves
Temperature
Control with
Interior Light
Air Flow
Control
Full-Width
Door Shelves
Freezer
Door Shelves
Dairy
Compartment

DOOR HANDLE INSTALLATION
For refrigerators with a mounting screw installed
on the face of both doors:
Remove both handles from inside freezer
compartment and screws from parts-included
bag.
FREEZER DOOR HANDLE
1. Place the tapered end of the handle over the
mounting screw on the freezer door and gently
slide handle in the direction of the flat end of
the handle. (Fig. 1)
2. Once the handle is fully seated around the
mounting screw, slowly rotate the flat end of
the handle toward the bottom of the freezer
door.
3. Open the freezer door and install the screws
into the underside of the freezer door through
the flat end of the handle. Do not use power
tools to install screws. Do not over-tighten the
screws.
REFRIGERATOR DOOR HANDLE
1. Place the tapered end of the handle over the
mounting screw on the refrigerator door and
gently slide handle in the direction of the flat
end of the handle. (Fig. 1)
2. Once the handle is fully seated around the
mounting screw, slowly rotate the flat end of
the handle toward the top of the refrigerator
door. (Fig. 1)
3. Open the refrigerator door and install
the screws in to the top of the refrigerator
door through the flat end of the handle
Do not over-tighten screws. (Fig. 2)
4. If re-installing handles after reversing the
door swing, remove screw hole plug from
the parts-included bag and place it in the
handle-mounting screw hole on the face of the
refrigerator door.
5. The name badge can be removed by using a
putty knife or flat head screwdriver to pry the
badge off the door face, being careful not to
damage the finish. Any residue left on the face
of the door from the badge should be removed
by using Goo Gone©or WD-40©. Be sure to
follow the manufacturer’s instructions when
using these products.
Do not use any abrasives or scouring pads to
remove the residue.
An extra logo badge is provided in the parts-
included bag with your refrigerator. That badge
can be used to cover the handle mounting screw
hole on the face of the freezer door.
DOOR HANDLE INSTALLATION
PAGE 8 • SET UP & USE
ENGLISH
Fig. 1
Fig. 2

DOOR HANDLE INSTALLATION
For refrigerators without a mounting screw
installed on the face of both doors:
Remove both handles from the freezer
compartment and the screws and handle trim
pieces from the parts-included bag.
FREEZER DOOR HANDLE
1. Mount the tapered end of the handle to the
door face using the enclosed screw. Do not
use the screw hole closest to the center of the
handle.
2. Attach the flat end of the handle to the
underside of the door using the enclosed
screws.
3. Insert tab on handle trim cover into slot in
handle and then press firmly onto handle.
REFRIGERATOR DOOR HANDLE
1. Mount the tapered end of the handle to the
door face using the enclosed screw. (Fig. 3) Do
not use the screw hole closest to the center of
the handle.
2. Attach the flat end of the handle to the top of
the door using the enclosed screws. (Fig. 4)
3. Insert tab on handle trim cover into slot in
handle then press firmly onto handle. (Fig. 5)
4. If re-installing handles after reversing the
door swing, remove the screw hole plug from
the parts-included bag and place it in the
handle-mounting screw hole on the face of the
refrigerator door.
5. The name badge can be removed by using a
putty knife or flat head screwdriver to pry the
badge off the door face, being careful not to
damage the finish. Any residue left on the face
of the door from the badge should be removed
by using Goo Gone©or WD-40©. Be sure to
follow the manufacturer’s instructions when
using these products.
Do not use any abrasives or scouring pads to
remove the residue.
An extra logo badge is provided in the parts-
included bag with your refrigerator. That badge
can be used to cover the handle-mounting screw
hole on the face of the freezer door.
PAGE 9 • SET UP & USE
ENGLISH
DOOR HANDLE INSTALLATION CONT.
Fig. 3
Fig. 4
Fig. 5

DOOR SWING REVERSAL
On black or white models, the door hinges and
handles can be reversed to accommodate your
needs.
NOTE: Door reversal is not available on stainless
steel door models.
REMOVING THE HANDLES
Please refer to the appropriate Door Handle
Installation section to determine how to remove
the handles from your refrigerator.
REMOVING DOORS AND HINGES
1. Use adhesive tape to secure both sides of the
freezer and refrigerator doors to the sides of the
cabinet. (Fig.6)
2. Remove the hinge cover screw and the top hinge
cover. (Fig. 7)
3. Remove the two bolts that mount the top hinge
to the cabinet and then remove the hinge by
raising it vertically. (Fig. 7)
4. Carefully remove the adhesive tape holding the
freezer door to the cabinet while holding the
door to the cabinet.
5. Remove the door by (a) pulling the top of the
door away from the cabinet and (b) lifting it at
the same time. (Fig. 8)
6. Move the door stop on the bottom of the door
to the opposite side and secure with original
screws, then place the door aside.
7. Unscrew the center hinge pin by rotating
counterclockwise, being careful not to lose the
spacers from the top section of the pin. (Fig. 10)
8. Remove the refrigerator door in the same
manner as the freezer door, first removing
the tape and then lifting up and away from the
cabinet. (Fig. 10) Relocate the door stop on the
bottom of the door to the opposite side of the
door. (Fig. 9) Place the door aside.
9. Remove the center hinge and spacer. (Fig. 11)
REVERSING THE DOOR
PAGE 10 • SET UP & USE
ENGLISH
Hinge Cover Screw
Hinge Cover
Bolts
Top Hinge
Thimble Hole
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11

10. Remove the bottom hinge by unscrewing the
bolts mounting it to the cabinet.
NOTE: It is easier to remove and re-install the
bottom hinge pin while the hinge is itself is
still attached to the cabinet.
RE-INSTALLING THE HINGES AND
DOORS
1. Unscrew the bottom hinge pin and re-locate
it to the opposite hole on the top of the hinge.
(Fig. 13)
2. Attach the bottom hinge spacer and bottom
hinge to the cabinet using the bolts originally
provided. Be sure to use the top two mounting
holes on the hinge and the bottom hole on the
same side that the hinge is being moved to.
3. Flip the center hinge according to the diagram
below and attach the hinge spacer and hinge to
the cabinet. (Fig. 14) Do not install the center
hinge pin yet.
4. Remove the top thimble cover on the hinge side
of the refrigerator door and relocate it to the
opposite thimble hole. Use both hands to mount
the door on bottom hinge pin, making sure the
pin goes fully into the bottom thimble hole.
When the top thimble hole is aligned with the
hole in the center hinge, place the hinge pin into
the hole, threaded end down, and tighten.
Do Not Over-Tighten
5. Remove the top thimble plug on the hinge
side of the freezer door and relocate it to the
opposite thimble hole. Place the door onto the
center hinge pin, being sure that the pin goes
fully into the bottom thimble hole. Tape may be
used as it was during the removal steps to hold
the door in place during the next step.
6. Place the top hinge pin into the thimble hole on
the same side as the lower hinges.
PAGE 11 • SET UP & USE
ENGLISH
REVERSING THE DOOR CONT.
Fig. 12
Fig. 13
Fig. 14
Thimble Hole
Fig. 15
Fig. 16

7. Replace top hinge cap and secure using original
screw.
NOTE: Prior to re-installing handles, remove the
Haier©logo badge from the face of the
door using a putty knife to gently pry it
from the door face. Any residue left on the
face of the door from the badge should be
removed by using Goo Gone©or WD-40©.
Be sure to follow the manufacturer’s instructions
when using these products.
Do not use any abrasives or scouring pads to
remove the residue. Use a putty knife to pry out
the plug buttons covering the handle mounting
holes on the face of the door, being careful not to
scratch the door finish.
To re-install handles, please see the Door Handle
Installation section.
REVERSING THE DOOR CONT.
FEATURES AND USE
PAGE 12 • SET UP & USE
ENGLISH
NOTE: All features not available on all models.
NOTE: If refrigerator has been placed in a
horizontal position for any period of time,
wait 4 hours after returning it to the upright
position before plugging it in.
TEMPERATURE CONTROL KNOBS
Your refrigerator will automatically maintain the
set temperature level. Turning the temperature
knob to the left will make both refrigerator and
freezer compartments warmer. Turning the knob
to the right will make both compartments colder.
You can turn the knob in either direction to adjust
the temperature to your needs. We recommend
setting the knob to the straight up and down
position and allowing it to run for at least 24 hours
before adjusting the temperature. Turning the
knob all the way left to the Off position will turn
off the refrigeration system, but does not remove
power to the refrigerator.
The freezer compartment also features a fan
tower knob, which is used to regulate air flow into
the compartment to fine tune the freezer. As with
the refrigerator temperature knob, we recommend
setting the knob to the straight up and down
position and allowing it to run for at least 24 hours
before adjusting it.
Refrigerator Temperature Knob
Freezer Fan Tower Knob
Fig. 17 7
6

PAGE 13 • SET UP & USE
ENGLISH
OPERATION INSTRUCTIONS
LIGHTING
All models come with an interior light located on
the ceiling of the refrigerator compartment. For
models with a single bulb, no cover is provided.
For models with dual bulbs, a cover is provided.
Some models may feature a light in the freezer
and/or a “mid-level” light on the back wall of the
refrigerator above the crisper. Please see the
Proper Care and Maintenance section for light bulb
replacement instructions.
REFRIGERATOR UPPER LIGHT W/ COVER
(NOT ALL MODELS)
To Remove Upper Light Cover (if included):
1. Push in the tab at the far end of the cover.
2. Rotate the far end of the cover down.
3. Push the cover toward the back of the
compartment.
REFRIGERATOR MID-LEVEL LIGHT (NOT
ALL MODELS)
To Remove Refrigerator Mid-Level Light Lens (if
included):
1. Push up on the bottom of the cover.
2. Rotate the bottom of the cover away from rear
of compartment.
3. Lift the top of the cover up and out.
FREEZER LIGHT (NOT ALL MODELS)
To Remove Freezer Light Cover (if included):
1. Pull the cover to the front of the cabinet.
REFRIGERATOR INTERIOR SHELVES
All refrigerator models include shelving that can
be adjusted to suit your personal storage needs.
Depending on model, shelves can be wire or
encapsulated glass, full-width or half-width.
FULL-WIDTH WIRE AND ENCAPSULATED
GLASS SHELVES
Can be adjusted to four different levels. These
shelves slide in and out by lifting the front of the
shelf and gently pulling it towards you.
HALF-WIDTH ENCAPSULATED GLASS
SHELVES
Can be set to 4 different levels and can be moved
independent of each other, giving you the widest
variety of shelving options. Keep in mind that
refrigerators with half-width shelving only have a
support track in the center of the refrigerator back
wall. Right-hand and left-hand shelves can’t be
interchanged.




OPERATION INSTRUCTIONS CONT.
PAGE 14 • SET UP & USE
ENGLISH
To adjust a half-width shelf, remove any items
on the shelf and tilt the front of the shelf up with
one had while stabilizing the shelf with the other.
Once the shelf is high enough for the rear hook to
disengage, you may pull the shelf toward you.
To move the shelf to another level, slide the
outside (non-center) edge along the side rail until
the back of the refrigerator is reached. Lift the
center side slightly to allow the rear hook to enter
the cantilever track. Then, slowly lower the center
of the shelf until it rests on the side rail and is
supported from the back by the cantilever track.
SNACK PAN (SOME MODELS)
Refrigerators that feature half-width encapsulated
glass shelves also include a snack pan.
If your refrigerator is equipped with a snack pan,
you will want to remove the pan before adjusting
the shelf that covers it.
To Remove the Snack Pan (if included):
1. Pull the pan out until it stops.
2. Pull up on the pan.
3. Pull the pan completely out of its track.
4. Follow the instructions above to adjust the shelf
to your desired height.
CRISPERS AND CRISPER COVER
To Remove a Crisper:
1. Slide the crisper out until it stops.
2. Lift the front of the crisper.
3. Pull out until it is removed.
NOTE: To remove a crisper on the same side as
the door, remove the bottom door bin first.
To remove the crisper cover, remove both crisper
pans using the instructions above:
1. Use one hand to push the crisper glass up from
underneath while taking hold of it from the top
with the other hand.
2. Use both hands to carefully pull the glass shelf
out and set aside.
3. Use both hands to lift the crisper frame up and
out of the refrigerator.
To replace the cover, insert the crisper frame back
into the refrigerator, gently replace the glass in the
recessed space in the frame and then replace the
crispers.

PAGE 15 • SET UP & USE
ENGLISH
OPERATION INSTRUCTIONS CONT.
CRISPERS AND CRISPER COVER (CONT.)
To Remove the Crisper Cover:
1. Remove both crisper pans using the instructions
above.
2. Use one hand to push the crisper glass up from
underneath while taking hold of it from the top
with the other hand.
3. Use both hands to carefully pull the glass shelf
out and set aside.
4. Use both hands to lift the crisper frame up and
out of the refrigerator.
To replace the cover in the refrigerator, insert the
crisper frame into the refrigerator, gently replace
the glass in the recessed space in the frame and
then re-insert the crispers.
CRISPER HUMIDITY CONTROLS
Each crisper pan has its own humidity control.
For fruits and vegetables with skins, move the
humidity slide to LOW.
For leafy vegetables, move the humidity slide to
HIGH.
DOOR FEATURES
Depending on the model, your refrigerator comes
with either full-width door racks or a combination
of a full-width door rack and half-width bins. To
remove either full-width racks or half-width bins,
use two hands to grasp both the bottom and top
edges of the bin or rack and lift straight up.
All models feature a dairy compartment with a flip-
up lid.
Some models feature a bottle hugger on the
bottom refrigerator door rack that can be adjusted
by gripping firmly and sliding left or right until it is
snug against items stored on the rack.
Crisper glass
Crisper frame

FOOD STORAGE INFORMATION
ENGLISH
FRESH FOOD:
• When storing fresh food that is not prepackaged,
be sure to wrap or store food in airtight and
moisture proof material unless otherwise noted.
This will ensure proper shelf life and prevent the
transfer of odors and tastes.
• Wipe containers before storing to avoid needless
spills.
• Eggs should be stored in an upright position in
their original carton to maximize shelf life.
• Fruit should be washed and dried, then stored
in sealed plastic bags before storing in the
refrigerator.
• Vegetables with skins should be stored in plastic
bags or containers.
• Leafy vegetables should be washed and drained
and then stored in plastic bags or containers.
• Hot food should be allowed to cool before storing
in the refrigeration. This will prevent unnecessary
energy use.
• Fresh seafood should be used the same day as
purchased.
• When storing meats in the fresh food section,
keep in the original packaging or rewrap as
necessary.
These are some suggestions for safe storage:
• Chicken 1-2 Days
• Ground Beef 1-2 Days
• Cold Cuts 3-5 Days
• Steaks/Roasts 3-5 Days
• Smoked/Cured Meats 7-10 Days
For detailed storage chart visit FDA website:
www.cfsan.fda.gov/~dms/fttstore.html
FROZEN FOOD
• Wipe containers before storing to avoid needless
spills.
• Hot food should be allowed to cool before storing
in the freezer. This will prevent unnecessary
energy use.
• When storing meats, keep in the original
packaging or rewrap as necessary.
• Proper freezer storage requires correct
packaging. All foods must be in packages, that
do not allow the flow of air or moisture in, or out.
Improper storage will result in odor and taste
transfer and will result in the drying out of the
improperly packaged food.
• Follow package or container instructions for
proper storage.
• Packaging Recommendations:
Plastic containers with air tight lids
Heavy duty aluminum foil
Plastic wrap made from saran film
Self-sealing plastic bags
• Do not refreeze defrosted/thawed foods.
• It is recommended that the freezing date be
marked on the packaging.
These are some suggestions for safe storage:
• TV Dinners 3 - 4 Months
• Fresh Shrimp, scallops, crawfish 3 - 6 Months
• Hamburger & stew meats 3 - 4 Months
• Ground Turkey, veal, pork 3 - 4 Months
• Chops 4 - 6 Months
• Steaks 6 - 12 Months
• Chicken or Turkey 6 - 8 Months
For detailed storage chart visit FDA website:
www.cfsan.fda.gov/~dms/fttstore.html
PAGE 16 • SET UP & USE

NOTE: Before using any cleaning products, be sure
to read the manufacturer’s instructions
and warnings. This will help avoid personal
injury or damage to property.
INTERIOR CLEANING:
Prepare a cleaning solution of 3-4 tablespoons of
baking soda mixed with warm water. Use a sponge
or soft cloth, dampened with the cleaning solution,
to wipe the inside of your refrigerator.
Avoid cleaning any cold glass (shelves, crisper
cover glass, etc.) with hot water. The glass can
break and cause personal injury. Handle all glass
parts with care at all times.
Do not attempt to wash any parts in a dishwasher.
Do not use harsh chemicals, ammonia, chlorine
bleach, concentrated detergent, solvents,
abrasives or metal scouring pads to clean your
refrigerator, inside or out. They can damage and/
or discolor the refrigerator finish.
EXTERIOR CLEANING:
Use a clean, soft, lightly dampened cloth with
kitchen appliance wax or a mild detergent to clean
the exterior of the refrigerator.
Use a clean, soft, lightly dampened cloth with
warm soapy water to clean the handles and trim.
Use a clean, soft towel to dry.
For stainless steel models, use a dry cloth and
stainless steel polish.
Door gaskets should be cleaned every three
months following the instructions for interior
cleaning. Clean gaskets will maintain a better seal
than dirty gaskets. Lightly apply petroleum jelly to
the hinge side of the gaskets to keep the gasket
pliable and assure a good seal.
Never use a dirty cloth to clean the exterior of
the refrigerator. Dirty cloths may leave residue
on the refrigerator that can damage the finish.
Also, avoid the use of harsh chemicals, ammonia,
chlorine bleach, concentrated detergent, solvents,
abrasives or metal scouring pads to clean the
outside of the refrigerator.
LIGHT BULB REPLACEMENT
1. In order to replace a light bulb, first unplug your
refrigerator from the power outlet.
2. After allowing bulb to cool, turn bulb counter-
clockwise in order to remove it from the socket.
3. Screw a new bulb into the socket by turning the
bulb clockwise.
4. Plug in your refrigerator and open the door to
check that the bulb is working.
To Tighten: Turn bulb clockwise
To Loosen: Turn bulb counterclockwise
PROPER CARE AND MAINTENANCE
PAGE 17 • CLEANING AND CARE
ENGLISH
Before changing a bulb, ALWAYS unplug unit from
the power source. Failure to heed this warning
could result in injury or death from electric shock.
WARNING
Before cleaning your refrigerator, ALWAYS
unplug it from the power source. Failure to heed
this warning could result in injury or death from
electric shock.
WARNING

ENGLISH
PAGE 18 • CLEANING AND CARE
PROPER CARE AND MAINTENANCE
LIGHT BULB REPLACEMENT GUIDE
Use the guide below to determine the appropriate
bulb for each fixture:
Upper Refrigerator Light - 40 W Daylight Appliance
Bulb (1 or 2 depending on model)
Mid-Level Refrigerator Light - 25 W Appliance Bulb
Freezer Light - 25 W Appliance Bulb
All bulbs have medium bases
POWER INTERRUPTIONS
In the event of a power interruption, unplug your
refrigerator from the power source. Avoid opening
the doors until after power has been restored.
Your refrigerator will maintain a cold temperature
for longer if door opening is avoided or kept to a
minimum.
Once power has been restored, plug your
refrigerator back into the power source and
inspect food in the refrigerator for spoilage
or thawing. Cleaning your refrigerator after a
prolonged power outage is strongly recommended
to avoid odors and potential health hazards due to
thawing.
VACATION
For long vacations or absences, unplug your
refrigerator and remove all food from it. Turn
the temperature control knob in the refrigerator
section to the OFF position and clean the
refrigerator, including the gaskets, according to
the Proper Care and Maintenance section. Leave
the doors propped open to allow air to circulate
inside the refrigerator.
MOVING
Before moving your refrigerator, empty the
food from it and use adhesive tape to secure all
loose items such as shelves, door bins and racks,
crispers and pans, etc. and unplug it. Always move
the refrigerator in an upright position in order to
avoid damaging the sealed refrigerant system.