Haier HWM85-9288 User manual

User’s Manual
Fully Automatic Washing Machine
This manual is for
Please read this manual carefully before using.
Retain it for future reference.
Index
Safety precautions............... 2
Packing list...........................
4
Names of the parts............... 4
Installation and
adjustment............................ 5
Preparation before
washing .................................
9
Use the operation buttons....11
Disposal after washing.........
14
Trouble-shooting Answer
to question............................ 15
Specification.........................16
HWM85-9288

2
Safety precautions
Contents marked with that symbol are actions forbidden to
perform. Performing of those actions may result in damage
of the machine or injure the personal safety of the user.
FORBIDDEN
Contents marked with that symbol are related to the safety
of the product and the personal safety of the users. Please
operate in strict conformity to the contents, otherwise it may
cause damage of the machine or injure the personal safety
of the user.
WARNING
Meaning and description of the symbols
Please check if power receptacle has good earthing condition before using to guarantee
your safety.
Please check if the water faucet is open, and if the connection of the water inlet pipe is
proper.
It is suggested to use foamless washing powder.
Please don’t use the washer in the environment below 0 °C; if the washer has been stored
below 0°C, please be sure to ensure the washer is placed under the room temperature
more than 2 hours and then use otherwise the washing effects may be lowered or the
washer may be damaged.
Please insert the power cord into special receptacle with rated voltage.
Be sure to use single-phase three pins receptacle.The earthing terminal of
the receptacle must be earthed reliably. If possible,please adopt electric
leakage protector.
The washing machine must be positioned so that the plug is accessible. Be
sure to pull the plug off and close the water faucet in following cases: power
failure, delivering the machine, setting the machine idle or cleaning the
machine.
Do not plug or pull the power plug with wet hand.
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacles
loose, do not use the plug any more.

3
In case the washing machine is installed on ground
with carpet, do not block the ventilation hole
with carpet. Ensure carpet does not obstruct the
opening in the bases.
Do not put the machine at damp place like the
bathroom. Never wash it with water. Do not put wet
laundries on the control panel.
Do not wash water-proof laundries like the raincoat,
bike covers etc. to avoid abnormal vibrations
in spinning. Wash the clothes that can float
on the water surface easily, please be careful
especially,for fear damage.
Do not stretch hands into the working machine. It is
dangerous even if the rotation is slow. Take special
care of the children.
Do not put any hot or heavy items (such as the
kettle with hot water ) on the washing machine.
Do not wash laundries with volatile materials (such
as thinner, petrol etc.)
The children shall not approach the working
washing machine.
Keep the machine away from direct sunlight and
heat source like the heater.
Do not decompose, repair or alter the machine by
yourself.
Do not use water hotter than 50 °C.
Alcohol

4
Packing list
Fully automatic
washing machine
Water inlet hose Bottom plate Tapping screws
(One Piece)
User’s manual
Warranty card
All illustrations in this Manual are
given for reference only. Your
products and accessories may
show differences from these
illustrations due to our continuous
improvement.

5
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is very important
to your security and correct operating the machine.
Adjust the adjustable foot:
To twist the adjustable foot, please first lift up the side of the foot slightly, and then you
can twist the two adjustable feet. Please make sure to keep the washing machine
in balance.
The adjustable foot
The washing machine away from wall should be overrun 20mm. The largest allowable slope
of the shank base of the machine is 2°. The slanting or rough ground will result in unstable
running or stoppage of the machine. Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is horizontal.

Soft items
Back
Front
Bottom plate
Section I enlarging
After you open the package, please lean
the washing machine gently down on soft
items (like the towel cloth, blanket, ect. ).
Install the bottom plate to the bottom of
the machine, then lift the machine up
gently. See to the figure:
Two claws at the bottom cover shall
be inserted in two bar-shaped holes
in the stand. Make sure the claws
are firmly in place.
Fasten the bottom plate to
base frame with one screw
High Low

6
Screw knife
Figure 4
Figure 5
About 4mm before twisting
About less than 2mm after twisting
Screw
Bushing
Sign plate
Screw nut
Figure 2 Figure 3
Figure 6
2.Loosen the screw till the water faucet can be
accessed. Put the jointer of the water inlet
hose on the faucet. See to Figure 2. (If the
faucet is too large and the jointer can not be
set on the water faucet,please loosen the four
screws and take out the bushing in the jointer.
The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
3.Fasten the four screws evenly. See to Figure 4.
4.Take off the nameplate. Twist the fastening nut
as per the indication of the figure to seal up the
exit end face of the faucet. See to Figure 5.
Remark: Before installation, the threading is
4mm above the upper surface of the nut.After
installation, the threading is 2mm above the
upper surface of the nut.See to Figure 6.
Connection between the water inlet hose jointer and the
water faucet
1.Press the lower end of the lock lever and push
down the slider. Take off the water inlet hose
jointer from the water inlet hose component.
See to Figure 1.
water inlet hose jointer
water inlet hose
Figure 1
Slider
Lock lever
The exit end face of the faucet
water faucet, suitable
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth.If not please file it to avoid leakage.
Confirm the water faucet


water faucet, not suitable
NOTE:The appliance is to be connected to the water mains using new hose-sets and
that old hose-sets should not be reused.

1.Do not take off the water absorption cushion. Please
check if the cushion is dropped or damaged before
each usage. If it happens please contact our
after-sale department immediately.
2.Put the nut of the water inlet hose on the valve
jointer.
3.Fasten the nut. Swing it gently to confirm if it's
suitable.
1.Push down the slider. Insert the water inlet hose
into the jointer.
2.Hang the lock lever to the jointer. Release the
slider till a click sound is heard.
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection between
the jointer of the water inlet hose and the water faucet, and
the installation of the water inlet hose are firm, so as to
prevent dropping from improper installation position.
1.Close the water faucet.
2.Press the locking lever. Push down the slider.Then pull off the water inlet hose.
If the machine is used frequently, the jointer of the water inlet hose can be kept
on the faucet to prevent damaging the fixing screw.
Dismantle the water inlet hose
Connection between the jointer of the water inlet hose and the
water inlet hose
Check the connection between the jointer of the water inlet hose
and the water faucet
Locking lever
Slider
water absorption
cushion
nut of the water
inlet hose
The jointer of the
water inlet hose
Slider
Locking lever
jointer of the
water inlet valve
Connection between the water inlet hose and the washer
7

8
The drain hose shall drain smoothly.
Do not trample or press the drain hose.2.The height of the drain hose shall be less
than 10cm , or the drainage will not be smooth,
and cost such long time that the machine may
stop at mid way.
1.
3.
5.
4.
If the drain hose is too long, cut it at mid
point. To make smooth drainage,cut the front
end of the hose slantingly.
If the extra hose is too long,cut it either at A or at B point.
If extra drain hose is needed,please
make separate purchase.The inner
diameter of the extra hose shall not
less than 30mm, and the length shall
not exceed 1.5m.
Remark: In order to make sure of the correct of installation, it is suggested to change the
direction of the drain hose with our company serviceman.
1.Dismantle the back cover of the washing machine.
2.Press the spring lamination lightly and pull the top
segment of the drain hose decumbent then put
down the drain hose from the drain hose frame.
3.Put down the drain hose, squeeze the drain hose
lightly and take off the hook, put the drain hose into
the cabinet. Take off the small baffle which installed
on the other drain outlet and install it on the side
which won't install the drain hose.
4.Extend the drain hose from the other side and install
it on the base by the drain hose frame
5.Install the back cover.
How to change the direction of the drain hose
Back cover
Drain hose frame
Spring lamination

9
Preparation before washing
Connect the water inlet hose. Open the water faucet.
Confirm that the washing machine is earthed reliably. Then insert
the power plug into the receptacle. The earth terminal shall not
link to gas pipeline and faucet water pipeline.

Put down the drain hose.
Slanting or uneven ground may result in unstable working or
abnormal noise. Please make the machine stand horizontally.

Clear the pocket. Take out the coins,sand, hairpins etc.
Confirm if there is special requirement for the laundries.
Check if the laundries are applicable for washing with machine.
Please repair the damaged cloth before washing in order to avoid the situation worse.
Divide the laundries that are not colorfast from other laundries.
Put those laundries difficult to absorb water into water with hand.
For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts
with heavy soil, please apply detergent on them in advance, which can make it easier to remove
the soil.

For those laundries that may get lint ball and those with long fur, turn it over before putting in.
Do not put those laundries polluted by chemicals into the washing machine directly.
The foreign materials will result in damage of the machine.
The quantity of the laundries shall not be too large. Stretch and loosen the
laundries before putting them in the tub.
When the pulsator is running, the buttons of the laundries may cause noise.
For the sake of discretion, please put the laundries with buttons into other
laundries.
Tie the long strips; fasten the buttons;close zippers.
Pay attention to followings before washing the laundries

10
How to use the whitener
How to use the washing powder
Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub.
Avoid using whitener on laundries with color or pattern as they are prone to lose color.
The whitener shall not touch the laundries directly.
Refer to the user’s manual for the usage and quantity of the whitener.
For powder whitener, please dissolve it before using.
Directly dissolved in the machine: (not applicable for fuzzy program )
.retawfoytitnauqllamslliF.1
completely.tievlossidotsdnoces03rofnuR.redwopehtddA.2
.levelretawelbatiustceleS.seirdnualehtnituP.3
The instant dissolving of the washing powder:
.reniatnocadnaC°03foretawmraweraperP.1
.tievlossidyllufotgnirritselihwredwopehtddA.2
The quick program, it is suggested to adopt liquid detergent instead of
washing powder to guarantee the washing effect.
Put in the proper quantities detergent according to the water level and the
laundries quantities.
It is suggested not to use high sudsingdetergent. Washing powder with poor
quality or long time storage maybe caked. Please pay attention to cleaning the
detergent box in time.
The capacity of washing and spinning of he machine refer to the largest weight
ofthe standard laundries under dry conditionthat can be washed or spinned in one
time. One time washing quantity shall be lower than the rated capacity.
The thickness, size, type of the cloth will influence the actual washing capacity. It
is suitable for one time washing to put in reasonable amount of laundries and the
laundries can be turned round in washing.
Do not select the high water level for laundries less than 1.0kg ,so as to avoid
splashing of water.

13
Use the operation buttons
Description of the function of buttons
4,6 or 8.
8
Favourite,Memory,Standard cycles
4
0.5h, 1.0h
2.0h
Favourite
Speedy
overflow overflow overflow
/Silk
HOLD

14
Disposal after washing
Please first pull off the power plug from the receptacle before cleaning.
After using, please clean the lint and foreign materials of the lint filter and
overflow filter in time. Otherwise it may influence your using the machine.
1
1
2
2
3 4
The method of
dismantle: Push it up
aslant and gently.
The method of install :
install it upwards and
aslant and push it in.
Clean the detergent box and set it on the control panel seat.
Cleaning the lint filter
Push down the spring
piece of the top lint filter
to make the claws out of
the filter cover, and then
pull out the lint filter to
get it down.
Put the lint filter into filter
cover, and make it tight .
Make sure the lint filter
well installed, or it can
influence your use.
Pull the back of the lint
filter, and then you can
get down it off the front
cover of the lint filter.
Sweep the rubbish in the
lint filter.
Put the back of the lint
filter into the front cover .
Notes:
The filter screen of the water inlet valve is likely to be blocked by foreign materials and
influence the water inlet. Please clean it with brush every two
months.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
After washing, close the water faucet.
( If needed, you can dismantle the water inlet hose).
Do not store water in the washing machine for a long period.
Drain the water completely after each using.
Be sure to pull off the power plug before maintenance.
Hang up the power cord.
Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid
for some time ( about 1 hour), then close the top lid.
Thinner
Petrol
Alcoho

15
Trouble-shooting Answer to question
Phenomena The reason How to settle
The digitron displays E0. ●The top lid is opened during
reserve procedure.
Close the top lid.►
The drainage cannot
work, or is too slow. The
digitron displays E1.
●Is the drain hose blocked?
●Is the drain hose put down?
Clean the foreign material. Open and►
close The top Lid Once.
It stops running in
midway. The digitron
displays E2.
●The top lid is not closed. Close the top lid.►
The safety switch acts,
and the spinning cannot
work. The digitron
displays E3.
●Are the laundries put slantingly?
●Is the machine slanting?
Reorder the laundries. Close the top lid.►
The machine will start running after 10►
seconds of being placed horizontally.
The water filling does
not work, or is slow, the
digital displays E4.
●Is the water tap opened, or is
there water supply failure?
●Is the water inlet valve blocked?
●Is the water pressure too low?
Open the water tap. Push the start/►
Pause button once.
Clean the water inlet valve then push►
the start/Pause button once.
Use after the water pressure is normal.►
The digitron displays E6. ●The water level sensor is bad. Please contact the after-sales service►
department.
The
machine
does not
act
Not wash ●Is there power failure?
●Is the power plug inserted tightly?
●Is the water level reached preset
position?
Please use it when there’s power►
supply.
Insert the power plug tightly.►
Fill water to the preset position.►
Not spin ●Is the power plug inserted tightly?
●Is the top lid closed reliably?
●Are the laundries set flat?
Insert the power plug tightly.►
Close the top lid.►
Set the laundries flat.►
There’s abnormal sound
inside the machine
●Is the machine slanting?
●Are the laundries put slantingly in
spinning?
●Are there any foreign materials?
Adjust the machine to be even.►
► Reorder the laundries and close the
top lid.
Remove the foreign materials.
►
(If there’s breakdown, please pull off the power plug before checking)
The following phenomena are not breakdowns sometimes. Please confirm again before sending it to
repair.
If there are real breakdowns, please come to the special maintenance department or after-sale
service department of our company. Do not repair it by yourself.
The water tap leaks ●Is the jointer of water inlet hose
loose or awry?
Fasten the jointer properly.►
► Put down the drain hose. Open and
close the top lid once.

Specification
Rated voltage/Frequency 220-240V ~ /50Hz
Water level / Water quantity (about) 1/20L, 2/29L, 3/38L, 4/46L, 5/54L, 6/60L, 7/65L,8/70L
Injection pressure 0.03 MPa ~ 1.0 MPa
Max Washing/Max Spinning capacity 8.5kg/8.5kg
Phenomena Explanation
The spinning is intermittent when it starts. Balance the laundries to avoid slanting.
Push the “spin” button to select “Spin”, but it doesn’t
work.
The program is setting the drain time. Some time is
needed before it starts spinning.
The final spinning is finished, it becomes rinsing and
begins to inlet water.
Because the washing clothes lean to one side,the
safety switch acts.After water filling and running,
eliminating the eccentricity of washing clothes,then
beginning to spin.
16
There may be some water flowing out of the drain hose
in the first use of machine.
It is the water remained in the factory inspection of
performance.