Haier XQS52-78 User manual

The ventilation
holes at thebottom
Before Using
Before Using
Safety precautions
In case the washing machine is installed on ground
with carpet, be careful not to block the ventilation hole
with carpet.
Do not put the machine at damp place like the
bathroom. Never wash it with water. Do not
put wet laundries on the control panel coating.
Do not let the machine share one receptacle with other
electric appliances. If the power plug is damaged, or
the plugging into the receptacle is loose, do not use
the plug any more.
Do not wash water-proof laundry like the raincoat,
bikecovers, down textiles etc. To avoid abnormal
vibrations in spinning and damages to the laundries.
Do not bend, stretch, twist, bind the power cord by force, or reformit.
Do not press or clamp it with heavy items. If the power cord and power
plug are bad, or the receptacle is loose, be sure to have it replaced by
the technicians of our special shop or our agent,or the after-sales service
department to avoid any risk.Keep the prong of the power plug clean.If
dust is found on the power plug, please wipe it off with dry cloth.
In normal usage of the washing machine, the power
plug shall be ready to be pulled or plugged with hang.
Be sure to pull the plug off and close the water faucet
when occurring power failure,delivering the maching,
setting the machine idle or cleaning the machine,Do
not plug or pull the power plug with wet hand.
earth
Do not use water with temperature higher than 50
Please plug the plug on special 220V AC receptacle.
Be sure to use three phase power receptacle.Ensure
the earthing prong of the power redeptacle is earth-
ed reliably.Use leakage protector if possible.
Soft object

Do not put hand into the rotating tub.It is dangerous
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
Do not decompose, repair or alter the machine by
yourself.
Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.
Do not wash laundry with volatile materials
(such as thinner, petrol etc.).
Keep the machine away from direct sunlight and
heat source like the heater.
The handicapped or children without care shall not
use the machine.
Please keep the lint filter in good condition, and
install it to proper position during washing. If the
lint filter is lost or damaged,please contact the local
after-sales service department of our company.
Benzene
Before Using
Before Using
Safety precautions
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpin
and other foreign materials before washing.
Please check if the water faucet is open, and if the
connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.

Install the bottom plate and lint filter
Please install and adjust the machine according to the requirement of the mannual.
It is very important to your security and correct operating the machine.
Before Using
Before Using
Installation and adjustment
After opening the package, please lean the washing
machine gently down on soft items (like towel cloth,
blanket, etc.). Installthe bottom plate to the bottom of
the machine with eight screwsby a cross screwdriver,
then lift the machine up gently. See to the figure:
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover, aimingthe inner cover
shaft to the installation hole of the correspondingouter tub cover shaft groove.
3.Firstly insert the inner cover shaft of one side into the correspon-ding outer tub
cover shaft groove, then push the another inner cover shaft into the corresponding outer
tub cover shaft groove. Please install to designated position to guarantee there are no
dropping or abnormal sound in opening and closing of the inner cover, and the operation
shall be smooth. Do not dismount the inner cover component after washing.
Install the lint filter
Install the inner cover
Install the lint filter in the balance ring.
I part zoom in
Press this part
Screw
Back
Front
bottom plate Soft object
Outer tube cover
Inner cover shaft
Inner cover

The drainage shall be smooth with the drain hose.
The height of the drain hose shall be less than
10cm, or the drainage will not be smooth, and cost
such long time that the machine may stop at mid
way.
Do not step on or press the drain hose.
If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed
1.5m.
If the extra hose is too long,cut
it either at A or at B point.
AB
<10cm
A
> 30mm
<1.5m
If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
Useage the drain hose
Before Using
Before Using
The largest allowable slope of the shank base of the machine is 1 .The slanting or rough ground will result in
unstable running or stoppage of the machine. Please adjust it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
Adjust the adjustable leg:
Adjust the Installation position
FastenLoosen
High Low
the adjustable nut
the adjustable feet
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
2 .After adjustment, fastenthe nut.

The exit end face of the faucet
Confirm the water faucet
Connection between the water inlet hose jointer and the water faucet
water faucet, suitable water faucet, not suitable
It is required that the front end shall be longer than 10cm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
3.Fasten the four screws evenly. See to Figure 4.
About 4mm before twisting
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut..(see to figure 6)
About less than 2mm after twisting
water inlet hose jointer
Screw knife
Screw
Bushing
Sign plate
Screw nut
water inlet hose
Figure 1
Figure 4
Figure 2
Figure 5
Figure 3
Figure 6
Slider
Lock level
Before Using
Before Using
Install the water inlet hose
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.

Connection between the water inlet hose and the washer
Dismantle the water inlet hose
Connection between the jointer of the water inlet hose
and the water inlet hose
Check the connection between the jointer of the water inlet hose
and the water faucet
1.Do not take off the water absorption cushion. Please check if the
cushion is dropped or damaged before each usage. If it happens
please contact our after-sale department immediately.
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
1.Push down the slider. Insert the water inlet hose into the jointer.
2 Hang the lock lever to the jointer. Release the slider till a click
sound is heard.
Locking level
Slider
water absorption
cushion.
nut of thewater
inlet hose
the jointer of the
water inlet hose
Slider
Locking level
jointer of the
water inlet valve
1. Close the water faucet.
2. Press the locking lever. Push down the slider. Then pull of the water inlet
hose.
If the machine is used frequently, the jointer of the water inlet hose can be
kept
on the faucet to prevent damaging the fixing screw.
Before Using
Before Using
2 Put the nut of the water inlet hose on the valve jointer.
3 Fasten the nut. Swing it gently to confirm if it's suitable.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.

Using process
Using process
1 Preparation before washing
Confirm if there's
special requirement
for the laundries.
Clear the pocket.
Take out the coins ,
sand,hairpins etc.
Fasten the buttons
and zippers.
When the pulsator is
running ,the buttons of
the laundries may cause
noise. For the sake of
discretion ,please put
the laundries with
buttons into other
laundries.
Preparation before washing
The quantity of the
laundries shall not
exceed the rated
value. The big
laundries like the
jeans shall be put
in loosely.
Pay attention to followings before washing the laundries
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries with unfast color from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into
mesh bag for washing.

Reference weight of the laundries:
working suit up,down
jeans about 800g
The capacity of washing of the machine refer to
the largest weight of the standard laundries under
dry condition that can be washed in one time.
Laundries quantity in one washing cycle shall
be lower than the rated capacity. The largest
capacity of this machine is 5.2kg.
The thickness ,size , type of the cloth will influence
the actual washing capacity. It is suitable to put in
reasonable amount of laundries and the laundries
can be turned round in washing for one time
washing.
Do not select " 4" water level for laundries
less than 1.0kg ,so as to avoid splashing of water.
shirt jacket
single bed sheet
socking
underpants
undershirt
pajamas
blanket
cotton,about 900g
cotton,about
300g
cotton,about
800g
cotton,about 600g
blending,about 50g
cotton,about 70g
cotton,about 180g
about 200g
Using process
Using process
2 Put in the laundries
cotton,about 1120g
coat with blended
cloth (about 800g)

How to use the whitener
Standard usage of the detergent and water quantity
Laundries
quantity
(kg)
Water
level
Water
quantity
Common powder,
Put the washing powder and softener into the detergent box
directly as Indicated in the left figure.
After that, please close the detergent box.Refer to the following
list for the usage of the detergent :he standard dosage of the
detergent and the water quantity.
How to use the washing powder
Fill water to decided level .Dilute the whitener with
container. Pour it slowly into the washing tub.
Concentrated powder,
Add 40g in each 30L water Add 25g in each 30L water
3 Put in the detergent Using process
Using process
Avoid using whitener on laundries with colour or
pattern as they are prone to lose colour.
The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and
quantity of the whitener.
For powder whitener, please dissolve it before use.
Below 0.5
About 50L
About 45L About 60g About 37g
About 38L About 51g About 32g
About 28L About 37g About 23g
About 20L About 27g About 17g
About 47L
About 42L About 56g About 35g
About 32L About 43g About 27g
About 24L About 32g About 20g
About 16L About 21g About 13g
About 67g About 42g
About 63g About 39g
Access for detergent and washing powder
Access for softerner
Directly dissolved in the machine (not applicable for fuzzy
program and reserve wash)
1.Fill small quantity of water.
2.Add the power.Run for 30 seconds to dissolve it completely.
3.Put in the laundry. Select suitable water level.
The instant dissolving of the washing powder:
1.Prepare warm water of 30 and a container.
2.Add the powder while stirring to fully dissolve it.In selecting
The super quick program, it is suggestedto adopt liquid
detergent instead of washing powder to guarantee the
washing effect.
The powder is more prone to pollute the laundry than the
detergent. Therefore please use it with suitable quantity.
It is suggested not to use high sudsing detergent.
Washing powder with poor quality or long time storage
maybe caked. Please pay attention to cleaning the
detergent box in time.
Detergent box

4 Use the operation buttons
Using process
Description of the function of buttons
Mode and meaning of the indicators
Flashing: indicate the running program
On: indicate the program about to run, or indicate the selected mode
Digital tube
During sensing, it displays
During operation of programs, it displays theremained time
(minute) or remained times of the corresponding procedure
Push the soak button to set the
soak procedure.
During standard and jeans
programs, push the soak
button to set different soak time
(10, 20, 30, 40 minutes)
During chemical fiber and
cotton programs, push the
soak button to select soak
procedure, but the soak time
cannot change.
During quick , super quick,
wool and silk programs, push
the soak button, the machine
have no reaction.
Soak button Wash button
Push the wash button to set
the wash procedure.
During standard and jeans
programs, push the wash
button to set different wash
time (from 0 to 16minutes)
During chemical fiber , cotton
wool and silk programs, push
the wash button to select
wash procedure, but the wash
time cannot change.
During quick, super quick,
programs, push the wash
button the machine have no
reaction.
Rinse button
Push the rinse button to set the rinse
procedure.
During standard and jeans programs,
push the soak button to set different
rinse times ( 0, 1, 2 times)
During chemical fiber , cotton wool and
silk programs, push the soak button to
select rinse procedure, but the rinse times
cannot change.
During quick , super quick , programs, push
the soak button, the machine have no
reaction.
During standard program, the machine is
set to save water program. If you push the
rinse button before starting operation, it will
change to water storage rinse program.
Push the spin button to set
the spin procedure.
During standard and jeans
programs, push the spin
button to set different spin time
(from 0 to 6 minutes)
During chemical fiber , cotton
wool and silk programs, push
the spin button to select spin
procedure, but the spin time
cannot change.
During quick ,super quick
,programs, push the spin
button, the machine have no
reaction.
Spin button
SOAK
WASH
RINSE SPIN
Minute
Minute
Times
Minute
XQS52-78

The washing machine can detect the laundries automatically. After detection,
it will set the water level to suitable value among 4, 6, 8,and 10 automatically.
You can also set water level by self. After the machine is started, it will not
set water level automatically. You shall push the start/pause button to make
new setting.
If there's water inside the tub, the machine cannot detect the laundries
and will display water level 6 .
If wet laundries are put in, it may display water level 10 . You must
set suitable water level by self.
If super quick program is selected, it will display water level 3 . When water
level 2 is reached in water filling, it will perform washing while filling water.
When water level 3 is reached, it will change to normal washing.
During operation of wash and rinse program, you can push down the
water level button to add water. When you release the button, or it reaches
the overflow water level, the machine will stop adding water.
The water level decided may be different from actual value because of the
different moisture level of the laundries.
Start/Pause button
Power On/Off button
Push the On/Off button to switch on the power.
When the power is on, push it again to switch off
the power.
Push the On/Off button to switch on the power.
If the start/pause button is not pushed, the
washing machine will automatically switch off the
power after 5 minutes.
Child lock function
10
8
6
4
2
9
7
5
3
1
/
()
()
Push and hold the water level button and spin button, then push
down the power on/off button. The digitron displays CL . You can
continue setting desired washing procedures. After setting, push
down the start/pause button. The child lock function is activated.
All of the buttons are locked and cannot make selection.
Release the child lock function: push down the water level and
spin button at the same time for more than 1 second. After a beep
sound, the child lock function is released.
+
XQB50-28
During sensing, it displays
During reserve procedure, it displays the remained reserve time (in hour)
During operation of programs, it displays the remained time (minute). If the remained time exceeds99 minutes,
it adopts A at tens place to represent 100 minutes, B to represent 110 minutes. For instance, A3 represents103 minutes.
In case of abnormal phenomenon, it displays the abnormal symbol (see to Page 16)
Page16
Reserve/remain
time indicator
digitron
Start
Pause
Power
On/Off
Reserve
Water level
Program
Chemical
fiber
Cotton
Wool
Silk
Standard
Quick
Super quick
Jeans
Child lock
ReserveReserve
In normal operation mode, the reserve indicator light is off. The time remain indicator light is on.
The digitron displays the time remained (in minute) before the washing is finished.
Push down the reserve button. The reserve indicator light is on The digitron displays the reserve
time of finishing washing (in hour). When the machine is started, the reserve indicator light is on,
indicatingthat the reserve function is running.
After the power is switched on, push it to
Start the machine
During working, push it to pause working.
During pause, push it to resume working.
Reserve button
Water level button
Program selection button
Following automatic programs are
available for selection
Program
Applicable situation
Standard
Common washing
Quick
Quick and high-efficiency wash
for common laundries
Super
quick
Super quick wash of the laundry
under 1 kg with light soil
Jeans
Washing the relatively big and
thick laundriesr
Chemical
fiber
Washing the chimical fiber
laundries
Cotton
Wool
Silk
Washing the cotton textiles
Washing the woolen textiles
Washing the textile

Using process
Using process
b
Steps of using the operation buttons and description of the steps
10
8
6
4
2
9
7
5
3
1
Chemical
fiber
Cotton
Wool
Silk
Reserve
Minute Minute
Times
Minute
Time reman
(Minute)
Reserve
(Hour)
XQS52-78
Power
On/Off
Start
Pause
Program
Water level
Quick
Super quick
Jeas
Standard
Spin
Rise
Wash
Soak
Push the "Power on/off " button to switch on the power.
POWER
ON/OFF
program
2Push the "program" button to select suitable automatic program.
After switching on the power, the machine will set standard program automatically. To select other automatic
program, push the "program" button till the relative indicator is on. Refer to the "program button" on Page
11 for the selection.
For instance: select "super quick" program for laundries with small
quantity and light soil.
Page 11
In selecting the standard program, the machine
will execute fuzzy program to select water
and wash time according to the cloth and weight
of the laundries. The full procedure is controlled
automatically.
Chemical fiber Standard
Cotton Quick
Wool Super quick
Silk Jeans
Push the "soak", "wash", "rinse" or "spin" button to select suitable procedure.
Minute
Minute
Times
Minute
Soak
Wash
Rinse Spin

Using process
Using process
After switching on the power, the washing machine will set to common program including"wash, rinse,
spin "automatically. To select other procedures, push the "soak", " wash", " rinse" or "spin" button
to select the time of soak, wash and spin, and the times of rinse. After switching on the power, if you
push one of the button among "wash", "rinse"and"spin", the digitron of the former procedures will
turn off automatically. The former procedures will not run. For instance: after switching on the power. If
you push the "spin" button first, it will execute spin singly after starting.
Attention
.
Even there's no water in the tub, a certain period is
required before spin starting.
Do not use the soak program for the woolen textiles.
Separate the laundries that are not colorfast from
other laundries in washing.
The pulsator will not rotate unless the water is
filled to selected water level.
The soak procedure can work in cooperation with automatic programs like standard, jeans, chemical fiber and
cotton.There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during washing, and can not
make setting in other cases.
WATER
LEVEL
Press " WATER LEVEL "button,
select suitable water level
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "start/pause"
button, then push the "water level" button to set the water level. Refer to "standard dosage of detergent and
water quantity"in Page 9 and "water level button"in Page 11 for selection.
Page 9 Page 11
Water Level and Time Table for Each Program (self programming not included)
Program Water
level
Wash
(min)
Rinse (min/time) Spin (min) Total tim e
(min)
Standard 1-10 About
10-16
Save water program, total 10 around About 19-25
Quick 1-10 About 5 Save water program, total 10 around About 15
Super quick 3 About 2 Save water program, total 4 around About 6
Jeans 1-10 About 16 Rinse twice, about 5
each time
About 6 About 50
Chemical
fiber
1-10 About 12 Rinse twice, about 3 About 4 About 41
Cotton 1-10 About 10 Rinse twice, about 3 About 4 About 49
Wool 1-10 About 3 Rinse twice, about 2 About 3 About 24
Silk 1-10 About 5 Rinse twice, about 2 About 3 About 30

Push the "start/Pause" button
5 Close the lid 6 Finish washing
Using process
Using process
* Total time: including the normal water inlet time and drain time. The total washing time may be influenced by
the water inlet pressure and water level.
* Spin time: From the moment the intermittent spinning starts to the moment it stops running (the time displayed
on spin digitron is from intermittent spinning to the moment before inertia spinning; the time displayed on the
time remain digitron is the total remaining time)
* In soaking, after water inlet it will perform soaking for about 10-40 minutes, then perform washing, rinsing and
spinning.
* In selecting "super quick" program, the washing machine will set the complete procedures of water level
selectior, washing, rinsing and spinning automatically.
Push the "reserve" button to select suitable
reserve wash program Reserve
After switching on the power, the reserve program is set to off mode automatically. If you need to set the washing
procedure to be finished at reserved time, please push the " reserve " button to set the reserve wash program.
Refer to reserve button in Page 11 for selection
When the "reserve" function is activated, the indicator light of the program you have set
will be off. The "reserve (hour)" and "time remain" indicator lights will be on. During
reserve procedure, push the "reserve" button to display the reserve mode.
To change the running program or cancel the reserve setting, you
need to switch off the power and make new selection. the washing will be finished after 18 hours.
Confirm the operation of reserve program
Page
After Finishing wash
alarm automatically

Clean
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
Please clean it with brush every two months.
Using process
Using process
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence
your using the machine.
The lint filter must be used during washing.
It must be cleaned in time after each using
Lint filter:
1.Rotate the inner tub with hand till the lint filter reaches
the position convenient for you to take it off. Pull it up to
dismount.
2.Push it down to install.
3.Clean the filter screen after washing.
Clean the detergent box and set it on
the control panel seat.
1.The method of dismantle : Push it up aslant and gently.
2.The method of install : install it upwards and aslant
and push it in .
Dismantle
Dismantle
Install
Install
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
Please first pull off the power plug from the receptacle before cleaning.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (
about 1 hour), then close the top lid.
4.Hang up the power cord and drain hose.
3.Be sure to pull off the power plug before maintenance.
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.

The digitron displays E0.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
The water filling does not work, or is
slow. After about 15 minutes later,
the digital displays E4.
The drainage cannot work, or is too slow.
The digitron displays E1.
It stops running in midway. The digitron
displays E2.
The power voltage is too low.
The top lid is not closed.
The top lid is opened during reserve
procedure.
Close the top lid.
Close the top lid.
Is the drain hose put down?
Is the drain hose blocked?
Put down the drain hose. Open and close the
top lid once.
Clean the foreign material. Open and close
The top Lid Once.
Are the laundries put slantingly?
Is the machine slanting?
Reorder the laundries. Close the top lid.
The machine will start running after 10
seconds of being placed horizontally.
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the start/Pausebutton once.
Push the sStart/Pause button once.
The water level sensor is bad. Please contact the after-sales
service department.
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
Is the screw of the jointer of water
inlet hose loose or awry?
Pull off the power plug. Wait for the
voltage resuming normal before usage.
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Fasten the screw of the jointer properly.
The water tap leaks
The digitron displays E8.
The digitron displays E6.
There's abnormal sound
inside the machine
Phenomenan The reason How to settle
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.
The digitron displays E9. The power voltage is too high.
The machine does
not act
Not wash
Not spin
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Common phenomena
Phenomena Explanation
* The spinning is intermittent when it starts. * Balance the laundries to avoid slanting.
* The wash procedure pauses. * The cloth sensor is detecting the cloth. It will start
adding water after about 48 seconds.
* Select “ Spin” program, but it doesn’twork. * The program is setting the drain time. A certain
period is needed before it starts spinning.
* The pusaltor pauses during washing, rinsing
or adding water.
* It is to avoid splashing during water filling.
* There may be some water flowing out of the
drain hose in the first use of the machine.
* It is the water remained in the performance
inspection by the factory.

Packing list
Name
User's manual
Quantity
One
One
Storage position
Inside the document bag
Inside the accessory bag
Between the upper cushion of the
washing machine package and the
upper seal of the package carton
Inner cover component
Components of the
water inlet hose
Inside the accessory bag
Eight
Tapping screws St4x16-A
Bottom plate One
One
Computerized Automatic
washing machine One
Inside the accessory bag
Specification
Model XQS52-78
Rated voltage frequency 220V ~ 50Hz
Rated washing / spinning capacity 5.2kg (weight of standard dry cloth)
Water level/Water quantity (about)
Max water consumption
Injection pressure 0.03Mpa~0.78Mpa
Rated washing power 380W
Rated spinning power 260W
Weight About 36kg
Dimension L 560 mm W630 mm H 890 mm
About 75L(High water level; Standard program)
1/16L 2/20L 3/24L 4/28L 5/32L
6/38L 7/42L 8/45L 9/47L 10/50L