HAISEN HD06VCRH 3 (HN074) User manual

Sensor & Intelligent Control
Microwave Sensor for max 15M Height Plug & Play Design
Bi-level Dimmable, Daylight Priority Remote Control
≤0.5W
Operating Temperature
-20°C~+60°C
Motion Detection
0.5~1.5m/s
Warranty
5
IP Rating
IP65
Detection Range
Max,ø14m/45.92ft
Max,ø14m/45.92ft Ceiling Mounted
Sensitivity Setting
100%/75%/50%/25%
Daylight Threshold
2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/Disable
Stand-by Period
0s/10s/30s/1min/5min/10min/30min/+
Stand-by dimming level
10%/20%/30%/50%
Hold Time
5s/30s/1min/3min/5min/10min/20min/30min
Technical Data
Operating Voltage
10.5-15V DC
Operating Current
30mA±5%
Output
DIM 0-10V
Stand-by power
Microwave Power
<0.3mW
Microwave Frequency
5.8GHz±75MHz
Mounting Height
Max. 15m/49.2ft
Max. 15m/49.2ft Ceiling Mounted
On/Off Control Detection Area Daylight Sensor
Hold Time
Warranty Stand-by period Stand-by dimming level
Remote Control

15M Highbay
Factory Default Setting: Detection area 100%/ Hold time 5s/ Daylight threshold Disable/Stand-by period 0s/
Stand-by dimming level 10%. Can be customized default programming.
12VDC
PLUG & PLAY 12VDC HIGHBAY MICROWAVE SENSOR
HD06VCRH 3(HN074) In Accordance With

Sensor & Intelligent Control
Mechanical structure
Wiring Diagram
2
3
2 4 6 8 10 12 14 16 18
24 46
9
12
18 68 810 100
63
3
0
6
9
12
6
9
12
Detection Patterns
Highest mounting height is 15m
This figure indicates the maximum
distance at the highest mounting height
with 100% sensitivity.
0.5-1.0M/S
Ceiling Mounted Wall Mounted
Mounting
Height
Mounting
Height
Well Detected Area Possibly Detected Area
15
Ø28.82
Ø36.00
Ø52.00
20.00
6.00 12.00
43.96
44.00
DIM
LED+
LN
N
L
LED-
GND
12V
DIM GND 12V
LED Driver
HD06VCRH 3(HN074)

Sensor & Intelligent Control
LUX OFF
LUX ON
1. Standby period is +∞;
2.Standby dimming level is on 10%
20% or 30%;
3. Daylight threshold is on 2Lux,
10Lux or 50Lux.
Daylight Priority
Dusk/Dawn sensor:
Dual-PD technology brings a fully automatic dusk/dawn sensor which can tell the difference between natural
light and LED light, to ensure the light will be off when needed.
With Daylight priority function, HD06VCRH 3 is able to differentiate
artificial light brightness from natural light after installed inside the
fixture,
and automatically turn off light when ambient brightness exceeds preset
lux level.
Precondition of Daylight priority:
Natural Light
Light off automatically
light on automatically
Light automatically on
when ambient brightness
is lower than preset lux
level.
With insufficient
ambient brightness,
light dims to 100%
when motion detected
Light dims to standby level
if no motion detected after
holdtime.
Light off when ambient lux
level is higher than preset
lux amount.
Performance
1.Application——Lux on/off
Stand-by
period

Sensor & Intelligent Control
2.Automatically ON/OFF function
With sufficient daylight, even
when motion detected, light
remains OFF.
With insufficient daylight,
the sensor turns light ON
when m otion gets detected.
The sensor turns OFF light
automatically after the
holdtime when there's no
motion detected.
3.Daylight Disable
When daylight threshold
is preset as "disable", the
sensor turns light ON
when motion gets detect-
ed, and OFF after hold-
time.
The sensor turns light ON
when motion gets detected.
The sensor keeps light ON
for holdtime period after
motion leaves.
The sensor turns OFF
light automatically
after the holdtime.
4.Corridor Function, Bi-level Dimmable
With sufficient daylight,
the sensor keeps light
OFF even motion gets
detected.
With insufficient
daylight,
the sensor turns light
ON when motion gets
detected.
The sensor turns OFF
light automatically
after the standby
period when there's no
motion detected.
After there's no motion
detected, the sensor
keeps light ON 100% for
holdtime.
After holdtime, sensor
dims light to standby
dimming level for
standby period.
Hold time
Stand-by
period
Hold time
Hold time

Sensor & Intelligent Control
Attention
1. Please read the instructions carefully before using this product and keep it well for all
users to read at any time.
2. The sensor should be installed by qualified electrician and ensure power is off before the
installation.
3. We reserve the right to modify any incorrect text, image and necessary technical param-
eters.
4. Any unauthorized modification is forbidden, otherwise all guarantees will be immediately
invalid.
Installation precautions
1. Microwave sensor can be installed in any lamp except the one with
full metal shell.
2. The detected surface cannot be shielded by metal objects.
3. Make sure the microwave module is completely exposed outside.
4. The detection surface of the sensor module shall be installed
facing the detection area.
5. Should be kept away from the driver to avoid interference genera-
tion and lamp flashing.
6. Wiring must be strictly in accordance with the wiring diagram to
avoid short circuit.
Application Environment
1. Suitable for indoor installation to avoid false triggering due to exter-
nal factors such as rain, wind or tree swing.
2. Shall not be installed in the place with all four metal shelters and
small space (such as galvanized-iron roof ).
3. Shall note be mounted installation, so as to avoid false trigger
caused by the lamp itself shaking.
4. Shall not be installed next to large operating machines such as venti-
lator/ceiling fan to avoid false triggering caused by machine vibration.
User Notes
1.Microwave can penetrate walls or glass thinner than ＜20mm and
attenuate if thicker than ＜20mm.
2. The driver voltage shall be stable and float within 10%.
3. Detection area will be affected by speed of motion, mounting height
and movement volume.
4. Conduct test on sunny days without the lampshade which will affect
the tested lux value.

Sensor & Intelligent Control
REMOTE FOR DIMMABLE
SENSORS WITH MEMORY FUNCTION
ON/OFF Reset
1min
30s 3min
5min 20min
10min 30min
10%
30%
20% 50%
30s
10s 1min
5min 30min10min
+
-
50% 75% 100%
Detection Range
Hold Time
Stand-by period
Start Memory Apply
5s
0s
25%
Brightness
30Lux
10Lux
80Lux Disable
120Lux
Daylight sensor
2Lux
50Lux
Tes t
(2s)
Model: HD03R
Auto
Mode
Stand-by dimming level
1. "ON/OFF" key only functions as a switch of the light.
2. If press this button to turn off the lamp before it's short-circuited,
the lamp will remain off after power-on again.
+/-
Apply
Press "Start" to customize scene, users can change detection range,
daylight threshold, holdtime, standby dimming level and standby period.
1. Press "Memory" to save all the settings.
2. The settings remained as the last time if not get resetted values.
1. Press "Apply" to deliver the saved setting.
2. Press "Apply" without “memory”will make all the setting
one-time operation.
3. Settings should be done within 30S, otherwise it exits memory mode.
1. To adjust brightness 10-100% in on/off mode.
2. To adjust highest brightenss 60-100% in sensor mode.
ON/OFF
Reset
Auto
Mode
Start
Memory
Apply
+
-
Test
(2s)
Remote Keys Function Performance
Auto Mode
Reset
Start
ON/OFF
Memory
Detection area
Hold time
Stand-by period
Stand-by
dimming level
Test mode
Press “Auto Mode” button, the sensor starts to work and all settings
remain the same before the light gets switched on/off.
1.Press "Reset" button, change brightness to max level.
2.Press “Reset” button, products with DIP switch will be controlled by DIP
switches; otherwise all the setting will be just initial, that is 100% detection
range,hold time 5S, nostand-by time and daylight threshold disabled.
Detection area (Press to define detection area 100%/75%/50%/25%.)
Daylight Threshold
Hold time (Press to define holdtime 5s/30s/1min/3min/
5min/10min/20min/30min)
Stand-by dimming level (Press to define stand-by dimming
level 10%/20%/30%/50%.)
Stand-by period (Press to define stand-by period 0s/10s/
30s/1min/5min/10min/30min/+.)
Note: “0s” means no standby period; “+”
means unlimited standby period.
Daylight threshold (Press to define daylight level 2Lux/
10Lux/30Lux/50Lux/80Lux/120Lux/Disable.)
Note: Disable means light will be turned on once sensor
detects movement, regardless of the ambient lux.
The button “Test (2s)” is for testing purpose after commissioning. Pressing
this button, the sensor goes to test mode ( hold time is only 2s )

Sensor & Intelligent Control
1. ON/OFF button to turn on the light
2. RESET button so start programming
3. Choose necessary functional buttons of all the zones: detection
area, holdtime, standby dimming level, standby period and daylight
threshold
4. Done and leave it; the program has been well kept in the remote
now
How to Use HD03R
Sensor Programming:
For singla sensor testing purpose
1. ON/OFF button to turn on the light
2. RESET button so start programming
3. START button
4. Choose necessary functional buttons of all the zones, detection
area, holdtime, standby dimming level, standby period and daylight
threshold
5. MEMORY button to keep the program inside the remote
6. APPLY button to deliver the kept program
7. Done and leave it
For project programing purpose
@the 1st sensor
1. ON/OFF button to turn on the light
2. RESET button so start programming
3. APPLY button to deliver the kept program
@the rest sensors
1. ON/OFF button to turn on the light
2. Press + - Buttons on the right top corner to manually dim up or
down the light.
3. Press TEST(2S) button to test if the sensor has been well connect-
ed; it will keep light ON for 2S only.
Manually dimming: