HAISEN HD06VCRH User manual

This figure indicates the maximum distance at the highest mounting height with 100% sensitivity.
Detection coverage
Typical installation height 15m
HD06VCRH
Haisen Technology | 01Specifications subject to change without notice.©All rights reserved.
Technical data
Dimensions (Unit: mm)
1. Automatic On/off control with
Daylight sensor.
2. Optional detection range, holdtime ,
daylight threshold,
Stand-by period
and
Stand-by dimming level.
3. Remote control setting.
4. 5 year limited warranty.
15m
10-15M
Highbay
altitude
Daylight
threshold
Stand-by
period
Stand-by
dimming level
Hold
time
Detection
area
On/off
control
Remote control
setting
5
years
2 3 4 5 623456
Ceiling Mounted
2
4
6
8
10
12
14
16
Mounting
height
Wall Mounted
2 4 6 8 10 18161412
1
2
3
4
1
2
3
4
CoveredWell covered
Mounting
height
Detection area
DIM 0-10V
0s/10s/30s/1min/5min/10min/30min/+∞
10%/20%/30%/50%
Max,ø14m/45.92ft (ceiling mounted)
15m/49.2ft (ceiling mounted)
Operating voltage
Operating current
Output
≤0.5WStand-by power
Hold time
Daylight threshold
Stand-by period
Stand-by dimming level
5750-5824MHz
<0.3mW
Microwave frequency
Microwave power
Mounting height
Detection range
0.5~1.5m/s
Operating temperature
IP rating
12VDC
30mA±5%
IP65
Motion detection
-20°C~+60°C
Warranty 5 years
2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/Disable
25%/50%/75%/100%
5s/30s/1min/3min/5min/10min/20min/30min
LED Driver
Red: 12V
Grey: GND
Purple: DIM
DIM GND 12V
ø50
50
24
12
22.5
Wiring diagram
Sensor

Piug & Play
Haisen Technology | 02
Shenzhen Haisen Technology Co., Ltd., Tel: [phone] 丨Fax: [phone]丨Email: [email protected] 丨www.haisensz.com
Light off when ambient
lux level is higher than
preset lux amount.
Light automatically on
when ambient
brightness is lower
than preset lux level.
With insufficient
ambient brightness,
light dims to 100%
when motion
detected .
Light dims to
standby level if no
motion detected after
holdtime.
Application____Daylight priority
Daylight Priority
+
Base
Sensor Module
Empty Cover
Motion sensor
Motion sensor
No sensor
No sensor
+
The bottom part will be always on the lighting fixtures; if the function is needed, the
module will be placed inside; if no function needed, the module will be removed. It
doesn't hurt the looking of the whole pack.
Icon No icon
The cover with humanoid icon indicates
there is built-in microwave module with
sensor function; The cover without
humanoid icon indicates there is no
built-in module as well as sensor
function.
Natural light
Lux off
Lux on
light on automatically light off automatically
Precondition of Daylight priority:
1. Standby period is +∞;
2. Standby dimming level is on 10%, 20% or 30%;
3. Daylight threshold is on 30Lux, 50Lux, 80Lux or 120Lux.
With Daylight priority function, HD06VCRH 3 is able to differentiate artificial light
brightness from natural light after installed inside the fixture, and automatically turn
off light when ambient brightness exceeds preset lux level.
Dusk/Dawn sensor:
Dual-PD technology brings a fully automatic dusk/dawn sensor which can tell the difference between
natural light and LED light, to ensure the light will be off when needed.

Haisen Technology | 03
Shenzhen Haisen Technology Co., Ltd., Tel: [phone] 丨Fax: [phone]丨Email: [email protected] 丨www.haisensz.com
Installation Method
With insufficient
daylight, when motion
detected, light ON.
With sufficient daylight,
even when motion
detected, light remains
OFF.
After the stand-by
period, light OFF.
After last detection, the
light will be dimmed
down to the stand-by
dimming level
(10%,20%,30% or 50%)
after holdtime.
Hold time Stand-by period
3. Function Demo - Dimmable control/Corridor function
Hold time
After the last detection and
the present hold time
elapsed, light OFF.
With sufficient daylight,
even when motion detected,
light remains OFF.
With insufficient daylight,
when motion detected, light
ON.
After people leave the detection
area, light remains 100%
brightness within hold time.
When motion is detected,
the sensor will switch on the
light to 100% brighteness.
After the last detection and
the present hold time
elapsed, light OFF.
1. Automatically ON/OFF function:
Light on when detect movement and off after people leave at night. Applications: Corridor, Staircase.
1
2
1
2
3
2. No daylight function
The daylight threshold is set to "Disable".
Light on when detect movement, After people leave, Light off
after stand-by period .
Applications: Dim places such as Basement Parking, Underpass.

HD05R Remote Control Applications
The button “Test (2s)” is for testing purpose after
commissioning.Pressing this button, the sensor goes to
test mode (hold time is only 2s ).
Detection Rarea
Daylight Threshold
Stand-by dimming level
Definition of the ambient brightness; only when the
ambient brightness is lower than the preset specific lux
amount, the sensor will work; when it's preset as
"disable", the sensor works everytime it detects motion
regardless of the ambient lux level.
-
+
Increase or decrease the parameters.
Test (2s)
Scene
WM/PIR
Hold time
Stand-by period
Press “Reset” button, products with DIP switch will be
controlled by DIP switches; otherwise all the setting will
be just initial, that is 100% detection range,hold time
5S, no stand-by time and daylight threshold disabled.
The period of light keeping low output before it gets
completely off. When it's preset as --, the light always
keep at low output even no movement in the
detection area.
Turn on or turn off the remote control.
ON/OFF
Start
Memory
Apply
Press the button before choosing the parameters.
Press the button after choosing all the parameters to
save them.
Press the button to deliver the saved settings to the
other sensors directly.
Press the button to change the output power from 0% to
100%, it changes 5% every press.
Power %
Change from the microwave sensor function to PIR
sensor function, and the other around.
The area in which movement will trigger the sensor, 100%
detection area also means strong sensitivity.
The period of light keeping 100% brightness after
moving objects leave the detection area.
The definition of low output during the standby period.
Attention
Haisen Technology | 04
Shenzhen Haisen Technology Co., Ltd., Tel: [phone] 丨Fax: [phone]丨Email: [email protected] 丨www.haisensz.com
1. Please read the instructions carefully before using this product and keep it well
for all users to read at any time.
2. The sensor should be installed by qualified electrician and ensure power is off
before the installation.
3. We reserve the right to modify any incorrect text, image and necessary technical
parameters.
4. Any unauthorized modification is forbidden, otherwise all guarantees will be
immediately invalid.
1. Microwave sensor can be installed in any lamp except the one with full metal shell.
2. The detected surface cannot be shielded by metal objects.
3. Make sure the microwave module is completely exposed outside.
4. The detection surface of the sensor module shall be installed facing the detection area.
5. Should be kept away from the driver to avoid interference generation and lamp flashing.
6. Wiring must be strictly in accordance with the wiring diagram to avoid short circuit.
Installation precautions
1. Suitable for indoor installation to avoid false triggering due to external factors such as rain, wind or
tree swing.
2. Shall not be installed in the place with all four metal shelters and small space (such as
galvanized-iron roof ).
3. Shall note be mounted installation, so as to avoid false trigger caused by the lamp itself shaking.
4. Shall not be installed next to large operating machines such as ventilator/ceiling fan to avoid false
triggering caused by machine vibration.
Application Environment
1.Microwave can penetrate walls or glass thinner than 20cm and attenuate if thicker than 20cm.
2. The driver voltage shall be stable and float within 10%.
3. Detection area will be affected by speed of motion, mounting height and movement volume.
4. Conduct test on sunny days without the lampshade which will affect the tested lux value.
User Notes

HD05R Instruction
Memory & Apply Mode
1. Press "ON/OFF button" to turn on the light or off.
2. To reset the parameters, Please follow the steps as below:
Step 1 - Press ON, to turn on the light if it was off at the start.
Step 2 - Press "Start" to the well-setting sensor.
Step 3 - Press the button of Detection range, Hold time, Stand-by dimming level,
Stand-by period and Daylight threshold one after the other in sequence (Press "+/-" to
set parameters).
Step 5 – Press “Memory” to memorize the settings.
Note: The interval of each parameter setting shall be controlled within 30s.
Isolated Setting Mode
1. Press "ON/OFF button" to turn on the light or off. Press "Scene", the remote will
activate settings that were saved last or remain at the factory default settings.
2. To reset the parameters, Please follow the steps as below:
Step 1 - Press ON, to turn on the light if it was off at the start.
Step 2- Press any button of "Scene", Test" and "Apply" to begin the sensor detection
mode.
Step 3 - Press the button of Detection range, Hold time, Stand-by dimming level,
Stand-by period and Daylight threshold one after the other in sequence.
3. To programme other lights in the array that have similar sensors to the same
programme.
Step 1 - Press "ON" to the second sensor
Step 2 - Press "Apply"
Notes:
1. Settings will be saved automatically and remain until you press reset again.
2. Light will flicker when setting each parameter.
3. The icon will flash when setting the corresponding parameter.
Haisen Technology | 05
Shenzhen Haisen Technology Co., Ltd., Tel: [phone] 丨Fax: [phone]丨Email: [email protected] 丨www.haisensz.com
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not inst alled and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•Reorient or relocate the receiving antenna.
•Increase the sep aration between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used
in portable exposure condition without restriction.