Hamworthy Weymouth Series User guide

IMPORTANT NOTE
THESE INSTRUCTIONS MUST BE READ
AND UNDERSTOOD BEFORE INSTALLING,
COMMISSIONING, OPERATING OR
SERVICING EQUIPMENT
Weymouth Series Pressurisation
Units
Installation, Commissioning
and Servicing Instructions
Weymouth Standard & Advanced Models

Technical Enquiries 01202 662527/662528
To supplement the detailed technical brochures, technical advice on the application and use of products in the
Hamworthy Heating range is available from our technical team in Poole and our accredited agents.
Site Assembly 01202 662555
Hamworthy offer a service of site assembly for many of our products in instances where plant room area is restricted.
Using our trained staff we offer a higher quality of build and assurance of a boiler built and tested by the manufacturer.
Commissioning 01202 662555
Commissioning of equipment by our own engineers, accredited agents or specialist sub – contractors will ensure the
equipment is operating safely and efficiently.
Maintenance Agreements 01202 662555
Regular routine servicing of equipment by Hamworthy service engineers inspects the safety and integrity of the plant,
reducing the risk of failure and improving performance and efficiency. Maintenance agreements enable our customers to
plan and budget more efficiently.
Breakdown service, repair, replacement 01202 662555
Hamworthy provide a rapid response breakdown, repair or replacement service through head office at Poole and accred-
ited agents throughout the UK.
Spare Parts 01202 662525
A comprehensive spare parts service is operated from our factory in Poole, providing replacement parts for both current
and discontinued products. Delivery of parts and components is normally from stock within seven days. However, a next
day delivery service is available for breakdowns and emergencies.
Customer Services

HAMWORTHY HEATING LTD
WEYMOUTH 500001112/C
i
NOTE: THESE INSTRUCTIONS MUST BE READ AND UNDERSTOOD BEFORE
INSTALLING, COMMISSIONING, OPERATING OR SERVICING EQUIPMENT.
THE WEYMOUTH PRESSURISATION UNITS ARE INTENDED FOR USE ONLY IN
COMMERCIAL/LIGHT INDUSTRIAL APPLICATIONS.
THESE PRESSURISATION UNITS COMPLY WITH THE ESSENTIAL REQUIREMENTS OF THE MAHINERY DIRECTIVE 89/392/EEC
AMENDED BY 91/368/EEC, THE LOW VOLTAGE DIRECTIVE 73/23/EEC AMENDED BY 93/68/EEC AND THE ELECTROMAGNETIC
COMPATIBILITY DIRECTIVE 89/336/EEC AMENDED BY 91/263/EEC AND 92/31/EEC.
PUBLICATION NO. 500001112
ISSUE ‘C’
JUNE 2008
Weymouth Series Pressurisation
Units
Installation, Commissioning
and Servicing Instructions
Weymouth Standard & Advanced Models

HAMWORTHY HEATING LTD
WEYMOUTH 500001112/C
ii
CONTENTS
PAGE
1.0 INTRODUCTION ................................................................................................................................1
2.0 TECHNICAL DATA............................................................................................................................1
3.0 SEALED SYSTEM FUNCTION..........................................................................................................2
3.1 Terminology........................................................................................................................................2
3.2 Application ..........................................................................................................................................3
4.0 OPERATION OF THE PRESSURISATION UNIT..............................................................................4
4.1 Unit Operation.....................................................................................................................................4
4.2 Safety Functions (Advanced Only).....................................................................................................4
5.0 GENERAL REQUIREMENTS............................................................................................................4
5.1 Related Documents............................................................................................................................4
5.2 Mains Water Connections...................................................................................................................5
5.3 Expansion Vessels .............................................................................................................................5
5.4 Safety Relief Valve .............................................................................................................................5
6.0 INSTALLATION..................................................................................................................................6
6.1 Location ..............................................................................................................................................6
6.2 Pipework Connections........................................................................................................................6
6.3 Electrical Connection..........................................................................................................................7
6.3.1 Mains Connection...............................................................................................................................7
6.3.2 Safety Switches/Circuits On Advanced Only......................................................................................7

HAMWORTHY HEATING LTD
WEYMOUTH 500001112/C
iii
7.0 COMMISSIONING.............................................................................................................................. 8
7.1 Mechanical Installation...................................................................................................................... 8
7.2 System Flushing................................................................................................................................. 8
7.3 Electrical Installation........................................................................................................................... 8
7.4 System Expansion Vessel.................................................................................................................. 8
7.5 Initial Setting Of Both Standard And Advanced Units........................................................................ 9
7.6 Filling The Unit.................................................................................................................................. 10
7.7 Pressure Switch Adjustment............................................................................................................. 10
7.7.1 Pressure Switch Adjustment Apparatus........................................................................................... 11
7.7.2 Cold Fill Pressure Switch.................................................................................................................. 11
7.7.3 Lo Pressure Switch (Advanced Only)............................................................................................... 11
7.7.4 Hi Pressure Switch (Advanced Only) ............................................................................................... 11
8.0 FAULT FINDING.............................................................................................................................. 12
9.0 SERVICING SCHEDULE................................................................................................................. 13
9.1 6 Monthly.......................................................................................................................................... 13
9.2 12 Monthly........................................................................................................................................ 13
9.3 4 Yearly ............................................................................................................................................ 13
10.0 SERVICING AND REPLACEMENT OF COMPONENTS ............................................................... 14
10.1 Hamworthy Heating Recommended Spares.................................................................................... 14
10.2 Standard Pump Removal................................................................................................................. 14
10.3 Advanced Pump Removal................................................................................................................ 15
10.3.1 Pump Fitting On Both Units.............................................................................................................. 15
10.4 Inlet Valve On Both Units................................................................................................................. 15
10.5 Pressure Switches On Both Units.................................................................................................... 16
10.6 Pressure Gauge On Both Units........................................................................................................ 16
10.7 Non-Return Valve On Standard Unit................................................................................................ 17
10.8 Non-Return Valve On Advanced Unit .............................................................................................. 17
10.9 Expansion Vessel Diaphragm.......................................................................................................... 17
APPENDIX ‘A’ – Diagrams, drawings and Data ............................................................................................... 18

HAMWORTHY HEATING LTD
WEYMOUTH 500001112/C
iv
FIGURES PAGE
Figure 1 Basic Overall Dimensions...................................................................................................................1
Figure 2 Technical Data....................................................................................................................................2
Figure 3 Typical System Schematic Layout......................................................................................................3
Figure 4 Expansion Vessel Operation ..............................................................................................................3
Figure 5 Schematic Layout of the Standard and Advanced Units....................................................................4
Figure 6 Hamworthy Heating Expansion Vessels.............................................................................................5
Figure 7 Recommended Clearance Dimensions..............................................................................................6
Figure 8 Mounting Bracket Dimension..............................................................................................................6
Figure 9 Pipework Dimensions .........................................................................................................................7
Figure 10 Advanced Alarm Terminal ................................................................................................................. 7
Figure 11 Restrictor Inserts Standard.................................................................................................................9
Figure 12 Restrictor Inserts Advanced................................................................................................................9
Figure 13 Changing Advanced Restrictor Inserts.............................................................................................. 9
Figure 14a Float Adjustment Standard................................................................................................................ 9
Figure 14b Float Adjustment Advanced................................................................................................................9
Figure 15a Priming Screw Standard...................................................................................................................10
Figure 15b Priming Screw Advanced ..………………………………………………………………………………...10
Figure 16 Pressure Switch Adjustment.............................................................................................................10
Figure 17 Pressure Switch Adjustment Apparatus...........................................................................................11
Figure 18 Fault Finding Guide ..........................................................................................................................12
Figure 19 Pump Fittings....................................................................................................................................14
Figure 20 Standard Pump Wiring Terminals.....................................................................................................14
Figure 21 Advanced Pump Removal................................................................................................................15
Figure 22 Advanced Pump Removal................................................................................................................15
Figure 23 Advanced Pump Removal................................................................................................................15
Figure 24 Advanced Pump Removal................................................................................................................15
Figure 25 Weymouth Advanced Pump Wiring Terminal...................................................................................15
Figure 26 Capillary Nut .....................................................................................................................................16
Figure 27 Switch Wiring (Advanced Only)........................................................................................................16
Figure 28 Pressure Gauge................................................................................................................................16
Figure 29 Non-Return Valve On Standard Unit ................................................................................................17
Figure 30 Non-Return Valve On Standard Unit ................................................................................................17
Figure 31 Non-Return Valve On Advanced Unit...............................................................................................17
Figure A1 Wiring Diagrams ...............................................................................................................................19
Figure A2 Heating System Calculation Sheet...................................................................................................20

HAMWORTHY HEATING LTD 1
WEYMOUTH 500001112/C
1.0 INTRODUCTION
The pressurisation units in the Hamworthy Weymouth range are designed to maintain the minimum pressure
requirement of modern low/medium temperature, hot water sealed systems. The pressurisation units also provide
replacement water for losses from the systems.
Note! The pressurisation unit is not to be used for the initial filling of the system.
The Weymouth units are housed in a powder coated steel cabinet with removable cover. Housed in the cabinet is
a pump, connecting pipe-work and pressure switches. In the top of the cabinet is the header tank, with a float
valve. In the front of the cabinet is the systems pressure indication gauge.
The range has 2 models:-
1) The Standard with the following features: 2) The Advanced with
Pump control pressure switch All the features of the standard plus:
Non-return valve High/Low pressure switches
0 – 6 bar system pressure gauge Isolating Valve (between tank and pump)
2.0 TECHNICAL DATA
The basic overall dimensions of both units are shown in below Figure 1, complete dimensions are shown in Figure
9 on sheet 7.
All screw threads used in the Weymouth units conform to ISO 7/1 or ISO 228/1 for pipe threads where applicable
& ISO 262 for all general screw threads.
Performance and General Data is shown in Figure 2 (overleaf).
Figure 1 - Basic Overall Dimensions
STANDARD MODEL
ADVANCED MODEL

HAMWORTHY HEATING LTD 2
WEYMOUTH 500001112/C
Figure 2 Weymouth Pressurisation Units—Technical Data
Model Standard Advanced
Minimum cold fill pressure bar 1.0
Maximum cold fill pressure bar 3.4
Maximum operating pressure bar 7.0
Maximum Flow Rate l/min 6
Maximum water flow rate @
maximum cold fill pressure l/min 0.1
Weight (empty) kg 13 19
Weight (full) kg 16 27
Tank capacity litres 2.6 7.6
Factory Preset Values
Cold fill pressure bar 1.8
System low pressure switch bar - 1.3
System high pressure switch bar - 3.65
To suit system conditions
Maximum water flow temp °C 82
Maximum static height m 30
Minimum system operating pressure bar 3.3
Maximum system operating pressure bar 6.3
Safety relief valve setting (Not HHL supply) bar 4.0
Nominal pressure differential bar 0.4
Electrical Data
Pressure switch contact rating 15A 240V AC
Electrical Supply 230V AC 50Hz 1Ph
Start current amps 9
Run current amps 2.8
3.0 SEALED SYSTEM FUNCTION
Figure 3 shows the layout of a typical sealed system.
3.1 Terminology
Expansion Vessel Charge Pressure
The gas pressure in the expansion vessel with water connection open to
atmosphere
System Cold Fill Pressure
The water pressure in the system that the pressurisation unit is set to maintain

HAMWORTHY HEATING LTD 3
WEYMOUTH 500001112/C
Figure 3 Typical System Schematic Layout
3.2 Application
The system expansion vessel charge pressure is set 0.1 bar below the cold fill pressure. Before operation of the
boiler, with the system at cold fill pressure the expansion vessel is empty . As the system heats up the expanded
volume is absorbed by the expansion vessel. A small pressure rise occurs which is accommodated by the vessel.
When the system cools the pressure drops. If there has been some fluid loss the pressurisation provides
replacement.
Figure 4 Expansion Vessel Operation
1. Diaphragm position at the cold fill / charge pressure. The vessel is empty of system fluid.
2. Diaphragm position at the hot working pressure. The system volume has expanded due to the temperature rise. The gas in the vessel is
compressed. Acceptance factor = 0.35 maximum (recommended).
3. Diaphragm position at high system pressure. The boiler system is shut down by the system pressure switch on AdvancedUnit.
4. Diaphragm at the safety valve lift pressure. Caused by boiler temperature limiter failure for example. Acceptance factor = 0.5 maximum
(recommended).

HAMWORTHY HEATING LTD 4
WEYMOUTH 500001112/C
4.0 OPERATION OF THE PRESSURISATION UNIT
Figure 5 Schematic Layout of the Standard and Advanced Units.
4.1 Unit Operation.
A drop in system pressure due to, for example, loss of water, will cause the pump to maintain the pressure. As
the level of water in the tank reduces a ball valve allows new water into the tank. When the pump pressure switch
is satisfied the pump stops
4.2 Safety Functions (Advanced only):
The advanced unit is fitted with two extra pressure switches . A pressure above the high pressure limit set on the
unit will switch over the SPDT high pressure switch and a pressure below the low pressure limit set on the unit will
switch over the SPDT low pressure switch.
The switches can be connected to boiler safety circuits as shown in the wiring diagram supplied with the unit and
displayed inside the unit’s cover.
5.0 GENERAL REQUIREMENTS
5.1 Related Documents.
Pressure Systems and Transportable Gas Containers Regulations 1989.
It is the law that pressure system appliances are installed by competent persons in accordance with the above
regulations. Failure to install appliances correctly could lead to prosecution. It is in your own interest and that of
safety, to ensure that this law is complied with.
The installation of the pressurisation unit and expansion vessel MUST be in accordance with the relevant require-
ments of the Pressure System Regulations, Building Regulations, IEE Regulations and the bylaws of the local
water undertaking.
It should also be in accordance with any requirements of the local authority and the relevant recommendations of
the following documents:-
Applicable standards and documents are:
BS 7074 Application, selection and installation of expansion vessels and ancillary equipment for sealed water systems.
BS 6644 Installation of Gas Fired Hot Water Boilers 60 kW to 2 MW
BS 6880 Parts 1,2&3: Code of practice for low temperature hot water heating systems of output greater than 45 kW.
BS 6759 Part 1 (ISO 4126): Specification for safety valves for steam and hot water.
BS 3456 (CEE10 Part 1, CEE11 Part 1): Safety of Household and similar electrical appliances.
HSE Guidance note PM5: Automatically controlled steam and hot water boilers.

HAMWORTHY HEATING LTD 5
WEYMOUTH 500001112/C
5.2 Mains Water Connections.
All connections to local water mains must comply with WRAS Regulations including any local requirements. The
System temporary fill connection must be as per water supply bylaws & must be removed after initial
filling.
5.3 Expansion Vessels.
System expansion vessels must be constructed to BS4814 or BS6144.
The required expansion vessel size is detailed in the contract documents. If these are not available refer to
section 5.3.1, otherwise if in any doubt contact Hamworthy Heating Limited for comprehensive system sizing
information. Hamworthy Heating Ltd supply a range of suitable expansion vessels details are shown below. A
calculation sheet which can be used to determine a suitable volume for an expansion vessel can be found in the
Appendix.
Figure 6 Hamworthy Heating Expansion Vessels
5.4 Safety Relief Valve.
Must comply with BS6759 part 1, and be sized and installed in accordance with BS6644 & BS7074.
SALES REF NO. HAMWORTHY PART
NO.
TYPE TOTAL VOL. DIAPHRAGM PART
NO.
CONNECTION WT
kgs
HOT WATER
APPLICATIONS -
EPDM DIAPHRAGM
(0-100°C MAX)
HAF 60V 532712002 VERTICAL 60 532712030 R1 BSPT MI 13
HAF 80V 532712003 VERTICAL 80 532712031 R1 BSPT MI 14
HAF 100V 532712004 VERTICAL 100 532712032 R1¼ BSPT MI 15
HAF 200V 532712005 VERTICAL 200 532712033 R1¼ BSPT MI 40
HAF 300V 532712006 VERTICAL 300 532712034 R1¼ BSPT MI 50
HAF 500V 532712007 VERTICAL 500 532712035 R1¼ BSPT MI 80
HAF 750V 532712008 VERTICAL 750 532712036 R1½ BSPT MI 120
HAF 1000V 532712009 VERTICAL 1000 532712037 R1½ BSPT MI 150
HAF 1200V * VERTICAL 1200 * R1½ BSPT MI 530
HAF 1600V * VERTICAL 1600 * R1½ BSPT MI 10
HAF 2000V * VERTICAL 2000 * R1½ BSPT MI 700
* REFER TO HAM-
WORTHY HEATING
HAF 8 532712056 H/V 8 R¾ BSPT MI
HAF 16 532712057 H/V 16 R¾ BSPT MI
HAF 25H 532712010 HORIZONTAL 25 532712029 R1 BSPT MI 5
HAF 60H 532712011 HORIZONTAL 60 532712030 R1 BSPT MI 14
HAF 80H 532712012 HORIZONTAL 80 532712031 R1 BSPT MI 15
HAF 100H 532712013 HORIZONTAL 100 532712032 R1¼ BSPT MI 16
HAF 200H 532712014 HORIZONTAL 200 532712033 R1¼ BSPT MI 41
HAF 300H 532712015 HORIZONTAL 300 532712034 R1¼ BSPT MI 51

HAMWORTHY HEATING LTD 6
WEYMOUTH 500001112/C
6.0 INSTALLATION
The units are supplied inside strong cardboard boxes with foam padding and should be left in this packaging until
they arrive on site and are installed.
6.1 Location. Figure 7 Recommended Clearance Dimensions
The units are designed for wall mounting. A mounting bracket is supplied inside the unit taped to the front of the
tank. It is intended that this bracket should be fixed to the wall and the unit hung from it. Each unit also has two
holes in the back of the chassis for extra security. The corresponding holes in the wall should be drilled to suit
once the unit is mounted on its bracket. The bracket dimensions are shown in fig 8 below.
The pressurisation units can be installed on the floor if they are secured to a wall or support using screws
through the holes in the chassis.
6.2 Pipework Connections (Shown in Figure 9)
1) Mains water connection (½" BSP Male).
The units have a type ‘AF’ air gap to prevent backflow in accordance with Water Supply (Water Fittings)
Regulations 1999. The water supply connection must conform to all local WRAS regulations.
2) Overflow connection (22 mm and ¾” Female).
Overflow should be piped to where it will be safe but visible so it will be noticed and corrected.
3) System connection.
The system connection is via a 15MM compression fitting. The unit must be connected to the system by an
antigravity loop (see Figure 3). The antigravity loop must be made in pipe-work no smaller than the expansion
vessel connection, and have a minimum height of 2 metres. It should include a lock-shield (or lockable) valve at
the system connection point for servicing and an automatic air vent fitted at the highest point of the loop. The
antigravity loop must not be lagged but can be fitted with an optional kit to prevent freezing. Consult Hamworthy
Heating for details. The pipe-work and fittings must be pressure tested to 1.5 times the safety valve lift pressure.
Figure 8 - Mounting
Bracket Details

HAMWORTHY HEATING LTD 7
WEYMOUTH 500001112/C
6.3 Electrical connection.
Wiring diagrams for the Standard and Advanced units can be found fixed inside the cover of the unit and in the
appendix. All wiring to the pressurisation unit must be in accordance with the IEE regulations, and any local
regulations which apply. Note! If in any doubt a qualified electrician should be consulted.
6.3.1 Mains Connection
Both the Standard and Advanced are supplied fitted with a 1m flying lead for connection to the mains supply.
Mains connection must be via a fused isolator rated at 13 Amps and positioned locally to the unit.
6.3.2 Safety Switches/Circuits On Advanced Only
The SPDT hi and lo pressure switches can be incorporated into circuits to interrupt a boiler control signal, in
order to shut down the boiler in the event of a system fault condition. The boiler control system must be designed
so that manual resetting is required after a system fault condition.
The circuits are rated at 230 V ~50 Hz, 15A. NOTE if the factory set pressure switch levels are to be altered
terminal should not be connected at this stage.
The connection terminal and its location is shown in fig 10.
Figure 10 Advanced Alarm Terminal
Figure 9 - Pipework Connections
STANDARD ADVANCED

HAMWORTHY HEATING LTD 8
WEYMOUTH 500001112/C
7.0 COMMISSIONING
Weymouth Units are supplied factory set and tested to suit the system parameters shown in Figure 2. If the
application falls within these parameters the unit requires minimal commissioning checks.
7.1 Mechanical Installation.
Check that the Weymouth Unit and expansion vessel has been installed correctly, as detailed in section 6.3: Pipe
-work connections. Check also that all lock-shield or lockable valves are correctly set.
7.2 System Flushing.
Ensure that the system has been flushed and all foreign matter has been removed, including pipe scale.
Note! Should this material come into contact with the expansion vessel diaphragm it could result in premature
failure of the expansion vessel assembly.
7.3 Electrical Installation.
Before working on Weymouth units ensure all electrical circuits connected to it are isolated.
7.4 System Expansion Vessel.
To set or check the expansion vessel charge pressure the lock-shield valve between the Weymouth unit and the
vessel must be closed. The drain cock fitted on the base of the expansion vessel must be open to allow any water
in the vessel to escape.
A suitable gauge should be used to check the charge pressure. Generally a Schrader ‘car type’ valve is fitted
near the top of the expansion vessel. If the charge pressure is too high it can be reduced by depressing the centre
of the Schrader valve or by using a pressure gauge with an integral air release valve. If the charge pressure is too
low a small increase can be provided using a car foot pump other wise an oil free compressor or nitrogen bottle is
recommended.
Note! The expansion vessel charge pressure should be set to 0.1 bar less than the cold fill pressure.
When the correct pressure is set the Schrader valve protective cap must be replaced.
Check the integrity of the pipe-work. Ensure the lock-shield valve between the Weymouth unit and the expansion
vessel is open and the drain valve is closed. Ensure the air purge plug is fitted (near the top of the expansion
vessel).

HAMWORTHY HEATING LTD 9
WEYMOUTH 500001112/C
7.5 Initial Setting Of Both Standard And Advanced Units
1) Check water inlet supply, it MUST have a flow greater than 8l/min.
2) Flow Restrictors
Standard
Each Standard comes with a selection of inserts that can be fitted into the inlet valve to achieve the required
output:
Mains inlet pressure > 4 bar H.P. restrictor (narrow coils see fig 11) Figure 11 Restrictor Inserts Standard
Mains inlet pressure < 4 bar L.P. restrictor (wide coils see fig 11)
The restrictors are fitted by pushing them into the open end of the
Inlet before attaching the unit to the water supply (see fig 11)
Advanced
Each Advanced comes with a selection of inserts that can be fitted into the inlet valve to achieve the required
output:
Mains inlet pressure > 4 bar H.P. restrictor (white see fig 12) Figure 12 Restrictor Inserts Advanced
Mains inlet pressure < 4 bar L.P. restrictor (red see fig 12)
The HP restrictor is fitted in the inlet side of the float valve assembly. This
should be unscrewed in order to change the restrictor (see fig 13). The LP
Restrictor is clipped to the side of the valve assembly.
Figure 13 Changing Advanced Restrictor Inserts
3) If the cold water is from a tank then the tank must be at least 2m above the inlet for the header tank to remain
full when the pump is working at maximum rate. The pressurisation units should not be used to fill a heating
system.
4) Check that the unit has been connected to the system using a suitable isolation valve.
5) Check that the mains lead has been connected to a suitably fused and switched isolator.
6) The cold fill pressure switches on both the Advanced and Standard are factory set to the levels listed in figure
2 as are the Hi and Lo pressure switches. If these levels are unsuitable for the installation then adjustment
instructions are given in section 7.3.
7) Set the float to its lowest level. (fig 14)
Figure 14a. Float Adjustment Standard Figure 14b. Float Adjustment Advanced

HAMWORTHY HEATING LTD 10
WEYMOUTH 500001112/C
7.6 Filling The Unit
1) Check all connections and pressures. Open inlet isolation valve and fill the tank.
2) Undo the priming screw on pump head (fig 15). Prime until water appears. Close the screw and turn on the
pump (keeping system isolation valve closed). Pump should run for a few seconds until set pressure is reached.
Figure 15a. Priming Screw Standard Figure 15b. Priming Screw Advanced
3) Check for any leaks within the unit, if OK open system isolation valve and fill system via filling loop.
4) The unit will now monitor the system and keep it at the required pressure.
7.7 Pressure Switch Adjustment
The pressure switches are fitted with a scale to indicate the pressure at which they are set. This scale is to be
used for indication only. As all the pressure switches and the pressure gauge take readings from the same place,
the unit’s pressure gauge can be used to give an accurate reading when setting switching levels .
The switches should be set last, after all the other commissioning tasks are complete.
Figure 16. Pressure Switch Adjustment
All the pressure switches have a nominal pressure differential (Hysterisis) of 0.4 bar. This means that there will
be 0.4 bar between the pressure at which the switch changes state during a pressure rise and the pressure at
which it will change when the pressure is falling again or vice versa. For example if the cold fill pressure switch is
set to 3.4 bar then the switch will operate when the pressure rises to 3.4 bar causing the pump to stop. The switch
will not change over & start the pump until the pressure has fallen back to 3.0 bar.

HAMWORTHY HEATING LTD 11
WEYMOUTH 500001112/C
7.7.1 Pressure Switch Adjustment Apparatus
When adjusting pressure switches the unit must be set up with the apparatus similar to that shown in Figure 17
connected to the outlet. Figure 17. Pressure Switch Adjustment Apparatus
7.7.2 Cold Fill Pressure Switch
Designed to stop the pump when pressure reaches a preset level. Setting procedure as follows:
1). Ensure the system pressure is lower than the pressure the switch is to be set to.
2). Switch the unit on.
3) Introduce a small leak at the outlet.
4) Because of the leak the unit begins a cycle of starting and stopping. Adjust the cold fill pressure switch until the
starts at 0.4 bar below the required cold fill pressure.
7.7.3 Lo Pressure Switch (Advanced Only)
Designed to stop the boiler operating if the pressure falls below a preset level. Setting procedure as follows:
1) Set the cold fill pressure switch by following the procedure in section 7.7.2 & allow system to run to pressure.
2) Isolate the Weymouth unit from the mains electrical supply & from the boiler circuits
3) Introduce a small leak until the unit’s pressure gauge reading equals the required Lo pressure setting.
4) Stop the leak.
5) The lo pressure switch is lowest on the panel which pivots around corner for easy access (see figure 23).
7) Set the lo pressure switch to its highest level (adjustment is shown in fig 16)
8) The terminals at either end of the switch form a closed circuit. Adjust the switch until the circuit is open . A
meter across the two terminals will signal the change.
7.7.4 Hi Pressure Switch (Advanced Only)
Designed to stop the boiler operating if the pressure exceeds a preset level. Setting procedure follows:
1) Isolate the Weymouth unit from the mains electrical supply & boiler circuits.
2) Use the pressure source increase the pressure until the pressure gauge reads the required Hi pressure level.
3) Set the hi pressure switch to its lowest level (adjustment is shown in fig 16).
4) The terminals at either end of the switch form an open circuit. Adjust the until the circuit is closed. A meter
across the terminals will signal a change.
If needed figure 25 shows the wire colours of the switches.

HAMWORTHY HEATING LTD 12
WEYMOUTH 500001112/C
8.0 FAULT FINDING
General fault finding is shown in Figure 18. If the Weymouth unit still does not operate satisfactorily, consult
Hamworthy Heating for assistance.
Figure 18. Fault Finding Guide.
Fault Possible Causes Action
Pump will not run Unit up to pressure
No power to the unit
Isolator fuse blown
Cold Fill Pressure switch set
incorrectly
Cold fill pressure switch wired
incorrectly.
Pump seized or faulty
None
Check at source
Replace fuse in isolator. Note! Investigate cause of
blown fuse before restarting the unit
Adjust pressure switches (see section 7)
Check wiring against figure 25
Service or replace pump (see section 10)
Pump runs but will not build
up pressure Pump isolating valve closed (Advanced only)
Pump not primed
No water in tank
Pump non return valve jammed
Open valve (see fig 21)
Prime pump (see section 7.6)
Check water level and investigate if necessary
Check valve
Pump cuts in and out
rapidly (hunting) Pressure switches set incorrectly
Non return valve not sealing
correctly
System Leak
Adjust pressure switches (see section 7)
Clean valve seat or replace valve if necessary (see
section 10.7)
Trace leak and ensure system is sound
Pump runs continuously Cold fill pressure switch set
incorrectly
Cold fill pressure switch faulty
System leak
Adjust pressure switches (see section 7) *
Replace faulty switch (see section 10.5)
Trace leak and ensure system is sound
Pump cuts out at wrong
pressure Cold fill pressure switch set incorrectly
Cold fill pressure switch faulty
Adjust pressure switches (see section 7)
Replace faulty switch (see section 10.5)
Maximum system working
pressure too high Cold fill pressure switch set incorrectly
Cold fill pressure switch faulty
Adjust pressure switches (see section 7)
Replace faulty switch (see section 10.5)
Boiler switches off un-
expectedly Hi or lo pressure switches set incorrectly
Hi or lo pressure switches &
circuits wired incorrectly
Adjust pressure switches (see section 7)
Check wiring with Wiring diagram in appendix
System pressure runs
consistently at cold fill
pressure
Small system leak Trace leak and ensure system is sound.

HAMWORTHY HEATING LTD 13
WEYMOUTH 500001112/C
9.0 SERVICING SCHEDULE
The following is a recommended servicing schedule for the Weymouth unit and expansion vessel. If remedial
action is required, refer to section 10: SERVICING AND REPLACEMENT OF COMPONENTS. If in doubt consult
Hamworthy Heating.
9.1 6 Monthly
1) Check the expansion vessel charge pressure, as described in section 7.4. A significant drop in charge
pressure could be due to a faulty vessel diaphragm; replacement of diaphragm should be considered. See
section 10.9.
2) Briefly run the pump to check for rotor seizure. This could occur if the pump is not run for extended periods.
This can be accomplished by slightly opening the expansion vessel drain valve to initiate a leak.
Note! Ensure that the drain valve is closed after this operation.
9.2 12 Monthly
1) Check the ball float valve diaphragm seat for integrity and replace if necessary. Also check the plastic float for
soundness.
2) Check the expansion vessel for signs of external corrosion. If any deterioration is observed then it is
recommended that the frequency of inspection be increased.
3) Check the operation of the safety circuits if utilised on the Advanced unit.
9.3 4 Yearly
1) Remove the expansion vessel diaphragm as described in section 10.9 and inspect for wear/ageing.
Inspect the internal surface of the vessel for corrosion.
Significant corrosion can lead to failure of the vessel; replacement of the entire vessel should be considered.
If necessary replace the diaphragm as described in section 10.9.

HAMWORTHY HEATING LTD 14
WEYMOUTH 500001112/C
10.0 SERVICING AND REPLACEMENT OF COMPONENTS
Note! When servicing or replacing Weymouth components electrically isolate the unit and close the system and
expansion vessel isolating valves. The Advanced unit should also be isolated from the pressure alarm circuits.
When remaking screwed connections use a thread sealant .
The cover on the Standard unit is secured by one screw at the lower edge of the front panel and one screw on the
top panel. The cover on the Advanced unit is secured by one screw at the lower edge of the front panel only.
10.1 Hamworthy Heating Recommended Spares
Standard Spares
Advanced Spares
Part Part N° Part Part N°
Pump Assembly 530905046 Pump Assembly 530905045
Float Valve Assembly 531911037 Float Valve Assembly 531911038
Pressure Gauge 557002009 Pressure Gauge 557002009
Pressure Switch Assembly 533925005 Pressure Switch Assembly 533925005
Non-return valve cartridge 531911039 Non-return valve cartridge 531911040
NOTE! For any service/replacement parts the unit serial No. (on the Data Plate inside the unit) MUST be
quoted. For service or spares contacts please refer to the inside front cover of this guide.
10.2 Standard Pump Removal Figure 19 Pump Fittings
Hamworthy part n° 530905046
Pump Removal Sequence
1) Isolate the water supply from the unit.
2) Empty the unit’s header tank.
3) Once clear of water undo the bulkhead fitting (fig 19,1),
4) Undo the down pipe fitting (fig 19,2)
5) Unscrew the 2 pump assembly mounting screws (fig 19,3).
6) Once the pump assembly has been removed from the
unit the pump can easily be removed from the assembly.
The wiring terminals are inside the box on the top on the pump. The wiring layout can be found on the wiring
diagram in the appendix and on Figure 20 below.
Figure 20 Standard Pump Wiring Terminals