Hans Grohe Starck 10933 1 Series Installation guide

Installation Instructions / Warranty
Starck
10933XX1
Phoenix
17944XX1
Carlton
17935XX1
Phoenix
17945XX1
Massaud
18933001
Citterio
39925XX1
Citterio
39920XX1
Uno
38933XX1
Carlton
17933XX1
Terrano
37930XX1
Montreux
16830XX1
Terrano
37933XX1
Steel
35933801
QUATTRO
DIVERTER
Trim Sets
Montreux
16834XX1
Citterio M
34930XX1

2
These trim kits fit Quattro diverter rough 13932181.
Starck
10933XX1
Montreux
16830XX1
Carlton
17933XX1
Carlton
17935XX1
Phoenix
17945XX1
Steel
35933801
Terrano
37930XX1
Terrano
37933XX1
Uno
38933XX1
Citterio
39920XX1
Citterio
39925XX1
Massaud
18933001
Phoenix
17944XX1
Montreux
16834XX1
Citterio M
34930XX1

3
Seal the wall around the rough
with waterproof sealant.
Failure to seal the wall can lead
to possible water damage.
Sleeve and escutcheon assembly
Remove the cover (1).
Seal around the rough-in with waterproof sealant
(2).
Starck 10933XX1, Montreux 16830XX1/
16834XX1, Phoenix 17944XX1/17945XX1,
Terrano 37930XX1/37933XX1, Uno 38933XX1
and Citterio 39920XX1/39925XX1 only:
Push the guide ring into the body of the rough-in.
Install the trim sleeve and the escutcheon.
(Special assembly for Massaud, see next page)

4
Massaud 18933001
Install the trim sleeve and the escutcheon.
Handle assembly
Starck 10933XX1
Montreux 16830XX1/16834XX1
Terrano 37930XX1/37933XX1
Push the handle onto the shaft.
Tighten the screw.
Cover the hole with the screw cover.
Carlton 17933XX1 / 17935XX1
Phoenix 17944XX1 / 17945XX1
Push the handle onto the shaft.
Tighten the screw
Phoenix cross handle only: Cover the hole with the
screw cover.

5
Steel 35933801
Citterio M 34930XX1
Uno 38933XX1
Tighten the screw by hand only three turns.
Snap on the handle.
Tighten the screw.
Cover the hole with the screw cover.
Citterio 39920XX1 / 39925XX1
Massaud 18933001
Install the handle snap connector and tighten the
screw.
Snap on the handle
Tighten the hollow set screw with a 2 mm Allen
wrench.

6
Spare parts
1 escutcheon Montreux 98669XX1
escutcheon Starck/Carlton/Phoenix/Steel/Allegroh/
Terrano/Citterio/Uno 13936XX0
escutcheon Massaud 98676000
escutcheon Citterio M 98963XX0
2 sleeve 96242XX0
3 guide ring
4 handle Starck 10993XX1
4.1 screw cover Starck 96540XX1
5 cross handle Carlton 17298XX1
6 lever handle Carlton 17993XX1
7 handle Steel 35993801
7.1 screw cover Steel/Allegroh/Uno, Phoenix cross 96541001
8 handle Montreux Lever 16693XX0
9 cross handle Terrano 37995XX1
9.1 screw cover Terrano 96542XX0
10 lever handle Terrano 37993XX1
10.1 screw cover Terrano 96543XX0
11 handle Uno / Citterio M 38993XX1
12 lever handle Phoenix 96632XX1
13 cross handle Phoenix 96792XX1
13 lever handle Citterio 39993XX1
15 cross handle Citterio 39995XX1
16 cross handle Montreux 16593XX0
16.1 screw cover Montreux 97987000
17 handle Massaud 18095001
XX = color code
00 chrome
62 oil rubbed bronze
80 steel
82 brushed nickel
83 polished nickel
Extension set 1 1/2” 92630000
(if needed, please order separately)

7
1
2
345
6
7
9
10
11
12
13
14
15
16
7.1
9.1
16.1
7.1
10.1
8
16.1
4.1

8
1
17
11
1
7.1

9
Cleaning Recommendation for Hansgrohe Products
Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the
market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when
cleaning.
Cleaning Materials for Faucets and Showers
Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the following points
when cleaning faucets and showers:
Only use cleaning materials which are explicitly intended for this type of application.
Never use cleaning materials which contain hydrochloric, formic, phosphoric, or acetic acid, as they cause considerable
damage.
Never mix one cleaning material with another.
Never use cleaning materials or appliances with an abrasive effect, such as unsuitable cleaning powders, sponge pads,
or micro fiber cloths.
Cleaning Instructions for Faucets and Showers
Please follow the cleaning material manufacturer’s instructions. In addition, pay attention to the following points:
Clean the faucets and showers as and when required
Use the amount of cleaning product and the amount of time recommended by the manufacturer. Do not leave the cleaner
on the tightenture longer than necessary.
Regular cleaning can prevent calcification.
When using spray cleaners, spray first onto a soft cloth or sponge. Never spray directly onto the faucet as droplets can
enter openings and gaps and cause damage.
After cleaning, rinse thoroughly with clean water to remove any cleaner residue.
Important
Residues of liquid soaps, shampoos, and shower foams can also cause damage, so rinse with clean water after using.
Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage.
Components with damaged surfaces must be replaced or injury could result.
Damage caused by improper treatment is not covered under the warranty.
•
•
•
•
•
•
•
•
•