Hanskamp MultiDos 035-000-000 Series User manual

MultiDos 035-000-000
036-000-000
EN
Installaon and operang instrucons
Item number: 010-100-000
Date: Nov 2017
Version 1.8 - Translaon of original instrucons for use
According to Annex 1 chapter 1.7.4 Machine guideline 2006/42/EG
Doenchem,
The Netherlands
www.hanskamp.nl/en
Vloeistof Doseersysteem
Liquid Dosing system
Flüsigkeit Dosiersystem
Liquide Systeme de dosage

2 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
Preface
Manual Contents
This manual contains the informaon necessary for the correct installaon and opera-
on of a Hanskamp MulDos.
Study and understand this informaon thoroughly before conguraon of the MulDos.
Failure to do so could result in damage to equipment. Please consult your milking equip-
ment dealer if you do not understand the informaon in this manual, or if you need
addional informaon.
All informaon in this manual has been compiled with care. Hanskamp shall not be lia-
ble for errors or faults in this manual. The recommendaons are meant to serve as
guidelines. All instrucons, pictures and specicaons in this manual are based on the
latest informaon that was available at the me of publicaon. Your MulDos may com-
prise improvements, features or opons that are not covered in this manual.
Applicability
The table below shows the type numbers of the MulDos for which this manual is
applicable.
Model designaon
Contact number Local Service Provider
We suggest you write the name, address, telephone number an E-mail address of your
local service provider contact in the table below. This makes sure you can easily nd the
informaon.
Name
Address
Telephone number
E-mail address
Model Type number
MulDos in Container (AC &DC) 035-001-000
035-002-000
036-001-000
036-002-000
Page 8 to 13)
MulDos wall mount (AC&DC) 035-003-000
036-003-000
(Page 14 to 17)

3 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
1. Introducon
MulDos by Hanskamp, a proven, sustainable technique enabling you to very easily
dose the right quanty of liquids per day and per cow. Smart, fast and
aordable. MulDos doses liquid propylene glycol like gravy on top of the feed chunks.
And cows love it!
The information in this manual is for farmers and technicians.
• Dairy farmers use the information to test and adjust the MultiDos or to list
overviews.
• Technicians use the information to install and setup the MultiDos.

4 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
2. Safety
2.1 Introducon
The safety alert symbol idenes important safety messages on your MulDos and in
the manual. When you see this symbol, be alert to the possibility of personal injury or
death. Follow the instrucon of the safety message.
Safety Alert Symbol
2.2 Signal Words
Note the use of the signal words DANGER, WARNING and CAUTION with the safety
messages. The signal word for each message uses the following guidelines:
Warning! Indicates a potenally hazardous situaon that, if not avoided, could
result in death or serious injury, and includes hazards that are exposed when
guards are removed.
Danger! Indicates a imminently hazardous situaon that, if not avoided, will
result in death or serious injury.
2.3 Safety Instrucons
You are responsible for the SAFE operaon and maintenance of your MulDos. You must
make sure that you and anyone else who is going to operate, maintain or work in the
vicinity of the MulDos knows all the related SAFETY informaon in this manual.
YOU are the key to safety. Good safety pracces protect you and the people around you.
Make these pracces a working part of your safety program. Make sure EVERYONE who
operates, maintains or works near the MulDos obeys the safety precauons. Do not
risk injury or death by ignoring good safety pracces.
• MulDos owners must train operators before they operate the
MulDos. This training must be repeated at least annually.
• The operator must read, understand and obey all safety and
operang instrucons in the manual.
• A person who has not read and understood all safety and operang
instrucons is not permied to operate the MulDos.
• Do not modify the equipment in any way. Unauthorized modicaon
may impair the funcon and/or safety and could aect the life of the
equipment, and persons.
• Only use approved spare parts, and make sure they are only installed
by authorized technicians.

5 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
2.3.1 General Safety
• Read and understand the manual and all safety signs before you connect
power supplies to operate or adjust the MulDos.
• Only trained persons are permied to operate the MulDos.
A rst-aid kit must be available near the MulDos. Store in a highly visible
place.
• A carbon dioxide or foam re exnguisher must be available near the
MulDos. Store the re exnguisher in a highly visible place.
• Install all protecve covers and guards before you operate the MulDos.
• Wear the correct protecve clothing and equipment. Disconnect and isolate
the electrical power supply before you clean or do maintenance on the
MulDos.
• Know the emergency medical centre number for your area.
• Contact your nearest milking equipment dealer provider if you have any
quesons
• Review safety related items with all operators frequently (annually).
2.3.2 Electrical Safety
• Only an authorized electrician must install the electrical power supply for
the MulDos.
• Make sure the electrical grounding of the electrical system and all parts of
the MulDos meet the local rules and regulaons.
• Replace any damaged electrical lines, conduits, switches and components
immediately.
• Isolate the electrical power supply before you open the MulDos to work
on the electrical system.
2.3.3 Installaon Safety
• Read and understand the instrucons in this manual.
• Make sure the MulDos is correctly installed.
2.3.4 Operang Safety
• Read and understand the applicable manual and all safety signs before you
connect power supplies to operate or adjust the MulDos.
• Only trained persons are permied to operate the MulDos.
• Switch o the electrical power supply by taking plug out of the power point
and secure the plug before you clean or do maintenance on the MulDos.
• Install the covers and guards before you operate the MulDos.
• Keep hands, feet, hair and clothing away from all the electrical parts.
• Keep unauthorized persons, especially small children away from the
MulDos at all mes.
• Before the electrical supply is aached to the MulDos, make sure all parts
are ght and that all the parts are in good condion.
• Contact your nearest milking equipment dealer if you have any quesons.

6 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
2.3.5 Maintenance Safety
• Read and understand the applicable manual and all safety signs before you
connect power supplies to operate or adjust the MulDos.
• Only trained persons are permied to maintain the MulDos.
• Switch o the electrical power supply by taking plug out of the power
point and secure the plug before you clean or do maintenance on the Mul-
Dos.
• Wear protecve clothing and safety goggles when you do work on the
pneumac system.
• Make sure all the covers and guards are installed when maintenance work
is complete.
2.3.6 Safety Decals
• General safety messages appear in this safety messages secon. Specic
safety messages are in applicable parts of this manual when potenal
hazards may occur if the instrucons or procedures are not followed.

7 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
3. Installaon instrucon
General comment:
The Hanskamp Mul-Dos-dosing system is a liquid dosing system. The MulDos
is suitable for uids with a low viscosity like Glycerine, Propyleen glycol, Tirsana
or Keto-protect which are based on water or oil. The MulDos is not suitable for
uids with a high viscosity.
The MulDos can also as the PipeFeeder and other Hanskamp dosators be linked to
any general feed system.
This instrucon will help you to install the MulDos-system (gure 1.).
Read this instrucon carefully and follow the safety instrucons. Examples of instal-
laon can be found at www.hanskamp.nl/en
Order numbers and names of accessories can be found in the aachment.
Transport and storage:
A complete MulDos system set consists out of a MulDos wall mount or a MulDos
-container with including 1 or 2 MulDos pumps. The container and/or wall mount will
be send in a box. These boxes can be put on each other on a pallet. The MulDos system
can also be send in a box.
Please note! Always use an appropriate vehicle (forkli truck, pallet fork,
pump truck, etc.) to move the pallet.
Please note! Parts may fall o the pallet when it is being unpacked.
Safety:
The user and installer are solely responsible for the safe operaon and maintenance of
the MulDos-system. In case of changing the HanskampQualityTube of the pump (art.nr.
003-512-00*), always disconnect the electric system.
Important: do not remove the sckers!
Maintenance of the sckers:
• Keep the safety sckers clean and legible.
• Clean the safety sckers with soap and water.
• Do not use any solvents or abrasives that could damage the safety sckers.
• Replace missing or illegible safety sckers.
• Safety sckers are obtainable from Hanskamp. Always specify the item numbers in correspondence.
Type descripon, to be found on the pump housing
Serial number
Arcle number
CE-marking
Art.nr. scker
1
1
Pag. 8 t/m 13 Pag. 14 t/m 17
Product name

8 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
Assembly Container-version
Look for the assembly of the wall-bracket version at page 14.
This manual contains the informaon for the installaon of one pump unit. When you
have two pump units, use exactly the same informaon to mount the second pump at
the other side of the container.
1. Check that all the parts are present using the item list. The list of materials can be
found in the appendix. (page 27)
Aenon! There are no connecon materials included to aach the pipe to
the feedstaon.
2. Aach the mounng pipe (art.nr.003-521-000) 1¼” (Ø 42,4) to a feed staon or
another feeding system.
3. Install the MulDos container over the pipe (g. 2)
4. Slide the container xer band (art.nr. 003-538-000) over the stand pipe unl it
touches the container. Mount the container xer band so that the container can’t
rotate. (g.4)
Aenon! During the assembly of the stand pipe, look for possible clip
danger.
Aenon! When the container runs easily on the tube, it should be xed.
When the container can make mulple rotaons it may impair the
operaon.
5. Unscrew the 3 Socket screw with ange (art.nr. 003-510-000) at the outside of the
MulDos-pump and detach the pump. (g. 5)
6. Take the PVC hose and cut this to size. This part becomes the delivery hose to the
sprayer.
7. Place the delivery hose (art.nr.001-006-005) into the hole of the container and
through the pipe (g. 6A and 6B.) This hose goes to the sprinkler.
Aenon! Watch out for minor injuries by sharp objects during the installa-
on of the hose trough the stand pipe.
Aenon! Make sure that the PVC hose keeps its shape during
the mounng of it. Don’t pull the e-wraps too hard, this can
pinch the hose.
8. For nozzle assembly see page 22.
1x pumphose Ø11.5 (HanskampQualityTube) (art. no. 003-512-000)
1x sucon hose = 20 cenmetre (PVC hose Ø10x7) (art. no. 003-575-000)
1x delivery hose = 5 meter (PVC hose Ø10x7)(art.nr.001-006-005)
3
6B
2
6A
With 2 pumps:
Also drill a hole Ø13 on the other side of the container (diag. 3). Aerwards aach the
extra supplied feed-through coupling (art. no. 003-572-000) in the hole and secure this
with a coupling nut (art. no.001-886-000).
5
4

9 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
9. Take the already present delivery hose and pull this through the rear wall of the
pump housing to the front.
10. Aach the feed-through coupling (art. no. 003-572-000) in the container and on
the delivery hose as indicated in diag.7.
11. Aerwards mount the sucon hose (art.no. 003-575-000) on the feed-through
coupling as indicated in diagram 8.
12. Take the pump, remove the four long screws (art. no. 003-509-000) and take the
transparent cover of the pump housing (art. no. 003-502-000) (diag. 9)
13. Push the end of the electrical cable from the motor into the hole of the container
which also contains the pressure hose. (g. 8)
14. Move the pump into the container, make sure the cable and the pressure hose
are not pinched.
15. Install the pump with the corresponding screws (art.nr. 003-510-000) evenly by
hand.
Take care! HanskampQualityTube is not suitable for acids.
A hose set suitable for acids is available from Hanskamp.
7
10
11
8
9

10 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
16. Take the delivery hose, HanskampQualityTube (which is located in the pump) and
1 feed-through coupling (art. no. 003-572-000). Mount this according to diagram
10 and 11.
Aenon! When assembling of the hose clamps there is a small chance of
clamp danger.
Aenon! Cut the hose o straight. When the hose is cut crooked, may im-
pair the operaon.
17. Turn the rotor of the pump loose by hand (counter-clockwise), and remove it
(g.12)
Aenon! By loosening of the rotor by hand, minor injuries can occur.
12
10
11
5

11 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
18. Bend the HanskampQualityTube around and slide this over the feed-through
coupling that scks out of the pump housing (g.16)
19. Bend the HanskampQualityTube as much as possible in the shape of the
casing. Press this to the delivery hose as far back as possible in the stand
pipe.
20. Take the Rotor and turn this with the side of the conical recess on the sha of
the pump motor. With the last turn press the HanskampQualityTube into the
recess of the pump housing. The hose is now wedged in-between the rollers
and the pump housing. Tighten the rotor by hand on the motor sha (g. 19
and 20). 16
17
18
19
20

12 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
Note! The tube must be placed as perfect as possible in the curve of the
pump (g. 21)
21. Take the transparent cover (art.nr. 003-502-000) with the associated four long
ange head screws (art.nr. 003-509-000). Posion the cover so that it is right for
the recess in the pump. Tighten the screws evenly unl the lid is ght. Note: solid
xed! (g. 22)
22. Connect the motor of the MulDos to the control board of the feeding staon.
First, make the control board voltage free, before connecng the motorcable
Aenon! When connecng the motor to the control board, it is possible
that light electric shocks can occur.
23. Always mount the cover, so that dirt and dust can’t fall into the container.
24. With one pump unit: mount a stainless steel blind plate on the other side of the
container. Fasten the blind plate with the including socket screws (g.24) (art.nr.
003-545-000)
Maintenance:
Check the MulDos on faults and wearing on a daily basis. Do this by means of a test
on the output of de tubes and electric cables. Check periodical the quanty and cali-
brate if necessary. When the HanskampQualityTube is worn by intensive use (leaking),
replace it according described steps. A repair kit is available by Hanskamp.
Also check the rollers and bearings for wear. Also these parts are available
as a repair kit by Hanskamp.
Aenon! Replace the HanskampQualityTube every year, or aer
pumping 1000L of uid.
Calibraon:
For calibraon: operate the motor manually ll the liquid emerges from the
nozzle.
Aenon! During the rst rotaons you will not see anything hap-
pen, this is because the rotor gets fastened to the axel of the
motor.
The MulDos is calibrated by allowing the feeding computer to emit a pulse ten
mes. Then you measure the amount of dispended liquid, divide this by 10 and
enter this value into the feeding computer.
Repeat this procedure every month and also
aer changing the liquid. This is one of the
possibilies for calibraon. When the manual
21
22
23
24
3545

13 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
Assembly Wallmounng-version
1. Check if all the parts are present using the item list. The list of materials can be
found in the appendix
2. Unscrew the 3 Countersunk Hexagon socket screw (art.nr. 003-510-000) at the out-
side of the MulDos-pump and detach the pump.
Aenon! Place the housing up to a maximum of 2 meters from the boom of
the storage tank.
The MulDos can be mounted on two dierent ways.
3a. Aach to a wall:
Drill holes in the back of the MulDos, as indicated in gure 28. Then secure the wall
mounng. (Mounng material is nog included)
3b. Installed on a surface:
Drill holes in the underside of the MulDos. The place of the holes is free
to choose, minimum distance between the tubes and the place is dis-
played in gure 27. Then secure the mounng material.( Mounng mate-
rial is not included).
25
26
28
27
Distance between the tube and
the plate: ± 8mm

14 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
4. Unscrew the casing of the pump housing.
5. Make a hole in the middle grommet with a small at screwdriver. Press
the cable of the motor through that hole. This cable gets aached to the
relevant control unit. For a correct installaon, consult the installaon
instrucon of the relevant control unit. Do this when the mounng of the
MulDos is completed.
6. Mount the feed-through coupling (art. no. 003-574-000) in the 2 outer-
most holes of the wall aachment and secure these with a union nut
(art.no. 001-886-000) as indicated in diagram 30.
7. Steadily screw the pump housing with the accompanying screws (art. no.
003-510-000) hand-ght on the wall aachment. (Diag. 29)
8. Loosen the rotor of the pump by turning an-clockwise and remove it
Aenon! By loosening of the rotor by hand, minor injuries can oc-
cur.
Aenon! Hanskamp only guarantees a correct operaon when the sucon
hose is 2 meters or shorter. Use the 5 meter hose as a delivery hose.
Aenon! HanskampQualityTube is not suitable for acids. A suitable hose kit for
acids can be ordered from Hanskamp upon request.
Aenon! Cut the hose o straight. When the hose is cut o skewed, it
may impair the operaon.
Aenon! Make sure that the end of the sucon hose is placed at the boom of
the container, otherwise the pump cannot pump all the liquid.
29
32
30
31
5

15 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
9. Take the right side of the HanskampQualityTube, and slide this on the feed-
through coupling (art. no.003-572-000).(Diag. 32)
10. Bend the HanskampQualityTube round and slide this over the le feed-through
coupling.
11. Now slide the sucon hose on the right feed-through coupling.
12. Repeat this with the delivery hose on the le-hand side.
13. Take the HanskampQualityTube, bend this as much as possible in the shape of the
pump housing. (diag. 35)
Take care! Always cut the hose square. If the hose is cut obliquely this can
adversely aect the operaon.
33
35
34
Motorcable to the
control unit
delivery-
hose
Sucon hose

16 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
14. Take the rotor to turn it on the side of the recess (protruding side) in the sha of
the pump motor. With the last ghtening turn, press the HanskampQualityTube
into the recess of the pump. The tube is now clamped between the rollers and the
pump casing. Turn the rotor by hand on the motor sha (g. 36 and 37).
Note! The tube must be placed as perfect as possible in the curve of the pump
(g. 37).
15. Take the transparent cover (art.nr. 003-502-000) with the associated four long
ange head screws (art.nr. 003-509-000). Posion the cover so that it is right for
the recess in the pump. Tighten the screws evenly unl the lid is ght. Note: solid
xed! (g. 38 and 39)
16. Connect the motor of the MulDos to the control board of the feeding staon.
First, make the control board voltage free, before connecng the motorcable.
Aenon! During the connecng of the motor to the control board, light
electric shocks can exist.
Maintenance:
Check the MulDos on faults and wearing on a daily basis. Do this by means of a test on
the output of de tubes and electric cables. Check periodical the quanty and calibrate if
necessary. When the HanskampQualityTube is worn by intensive use (leaking), replace it
according described steps. A repair kit is available by Hanskamp. Also check the rollers
and bearings for wear. Also these parts are available as a repair kit by Hanskamp.
We recommend to disconnect the rotor when the system is temporarily decommis-
sioned. Replace the HanskampQualityTube every year, or aer pumping 1000L of uid.
Calibraon:
For calibraon: operate the motor manually ll the liquid emerges from the nozzle.
Aenon! During the rst rotaons you will not see anything
happen, this is because the rotor gets fastened to the axel of
the motor.
The MulDos is calibrated by allowing the feeding computer to emit a
pulse ten mes. Then you measure the amount of dispended liquid, divide
this by 10 and enter this value into the feeding computer. Repeat this pro-
cedure every month and also aer changing the liquid. This is one of the
possibilies for calibraon. When the manual of your feeding computer
describes another method of calibrang, you need to apply that way of
calibrang the MulDos.
Installaon instrucon Process Computer
Nedap: (001-669-000 motor SolidState5)
-Dosage volume: 30 (equals 3cc dosage volume of MulDos)
-Interval/dispensing speed 5sec/0,6kg/min.
Congure the minimum and maximum feeding speed per interval according to the same
rao as feedstus 1 and 2. Thereto don’t enter the same numbers, but enter as a rao of
concentrates/ liquid addive.
Conguring liquid addive can be done in the same way as conguring chop. But the
dosage weight is a tenth (1/10) part of the programmed weight.
Example: Programmed feed 3: 0,10 is the same as 10cc liquid addive
Programmed feed 3: 1,00 is the same as 100cc liquid addive
36
37
38
39

17 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
Gascoigne Meloe (011-038-000 motor 24V AC 10RPM Time-controlled
GM 3000
1. Enter liquid addive as an extra feedstu in the GM3000.
2. Enter its name, “MulDos” in the processor.
3. Enter dosage at 0,5g/sec.
4. Enter minimum running me at 2sec.
5. Calibraon value 60sec.
6. Close-o me: not applicable.
Gascoigne Meloe (011-038-000 motor 24V AC 10RPM Time-controlled
ID 2000(+) and MR2000(+)
Key Data, change the following seng:
06 [enter]: Concentrate ? Yes
07 [enter]: Scale factor 1
08 [enter]: Min. Dispense 3 gram
10 [enter]: Eang speed 10,9g/sec.
Press the spacebar. The main menu appears again
Type 16 [enter]: Quit, to exit the ID2000 user program. The ID/MR2000 tools-menu 1.13
appears.
REMARK: When the Scale factor has been changed all data from all ID2000 Main con-
trollers have to be erased and cow data have to be re-entered again.
Feed staon Data: Change the following sengs:
09 [enter]: Auger? Yes
10 [enter]: Feed dispense 10,00g/sec.
11 [enter]: Auger stop me 131 msec.
All other feedtype(s):
01 [enter]: Auger? Yes
Press the ‘Arrow Up’ key to select Feed staon 2.
Repeat Chapter 3 for all other Feed staons or type 7[enter]: Entering per batch, to
change the sengs for a batch of selected feed staons.
Press the spacebar and type 16[enter]: Quit.
DeLaval ALPRO/DELPRO (Motor 011-044-000 AC 5 RPM with feedback)
In ALPRO
Menu 2:1 or Menu 2:6
In FP204
Menu 2 (F9)
General
0,05kg = ± 50ml liquid addive.
Calibrion
See ‘DeLaval ALPRO/feeding system book’ or ‘DeLaval ALRPO/program descripon in-
strucon book.’

18 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
Boumac 115V AC (001-436-000 motor bald 10RPM)
1. Enter liquid addive as an extra feedstu in the processor.
2. Maximize the intake speed of this feedstu.
3. Calibrate according to calibraon test results.
4. If the process computer cannot work with 1/100kg, mulply all values by 10.
Conguraon for propylene glycol is similar to conguring for concentrates. If the cali-
braon has been mulplied by factor 10, the conguraon should also be mulplied by
factor 10.
Example: Feedstu 3 is congured by 1kg to equal 100ml

19 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
Please note! In case of maintenance make sure to always rst switch o the
voltage and ensure that the storage container is empty.
Disassembly:
In case of disassembly all parts should be separated on material type and should be
processed in the right type of waste management system.
Please note! When disassembling the MulDos, there is a risk of clamping
danger. Also watch out for slight injuries on the hand, by grasping into the
roller mechanism.
Please note! During the cleaning of the tubing (ush) and grasping into the
roller mechanism with your hands, small injuries can occur on your hand.
With an uncovered motor ( no cover mounted) watch out for light electric
shocks.
Overview of included changes in this installaon-and operang instrucon:
Warranty limitaons:
The warranty excludes costs and expenses due to:
- incorrect use of the equipment, not in accordance with the specicaons in the in-
strucons for installaon and use;
- the consequences of any intervenon by engineers other than engineers recognised
and approved by Hanskamp for carrying out service, maintenance and other
technical work;
- incidents such as freezing, ice, re, ooding, inundaon or any other form of
extreme water damage, and lightning;
- defects in the electrical system or grounding system;
- damage to the electrical system due to vermin and so forth.
The warranty is not applicable to consequenal damage that is not related to the
machine itself. All systems have been tested. However, in the event of faults,
Copyright and disclaimer
The informaon given in this publicaon is provided for informaon purposes only and does not constute an oer for sale. The products supplied may
dier from those illustrated. No part of this publicaon may be reproduced or made public without prior permission in wring from Hanskamp AgroTech
BV. Although this publicaon was put together with the utmost care, Hanskamp AgroTech is not liable for any damage that might arise due to errors or
gaps in this publicaon.
The instrucons for installaon and use in Dutch are the original instrucons for installaon and use. The translaons into other languages have used the
Dutch instrucons for installaon and use as the source document. Hanskamp AgroTech does not accept any liability for dierences between the trans-
laons. If there are doubts about the content and accuracy of the translated instrucons for installaon and use, the Dutch instrucons for installaon
and use constute the authoritave document.
Nr. Release date Chapter(s) Notes
108/2014 First edion
1.1 10/2014 All Apply technical improvements
1.2 12/2014 Conguraon Conguraon for mulple feed-
computers
1.3 01/2015 Arcle structure Update + 36000No.
1.4 09/2015 All General inspecon
1.5 09/2015 Aachment 1 Use only 3518 spray nozzle
1.6 01/2016 General comment
and maintenance
1.7 05/2017 All Arcle structure changed
1.8 10/2017 Alle Art. no. 001-006-000 split up

20 - 30
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulDos
EN Dosing system – Dosiersystem – Systeme de dosage - Doseersysteem
4. FAQ
Common problem Possible cause Soluon
The liquid runs from the pump
back in the stock barrel
Leaking tube, worn rollers,
worn bearings
Replace the tube, replace the rollers, replace
the bearing.
Liquid runs out of the nozzle
while the motor doesn’t run
False air between the pump
and the nozzle
Press the hose on the nozzle again, check/
improve the sealing between the coupling and
nozzle again, mount the nozzle 100% vercal.
The motor runs but it doesn’t
pump any liquid
The sucon tube is closed,
rotor is installed the wrong
way.
Clean the sucon tube (possibly by blowing),
install the rotor in the right way.
Leaking feed-through coupling Hose too loose on the cou-
pling
Mount a hose clamp (art. no 001-153-000) on
the coupling/hose