Hanwha Vision LRN-1610S User manual

NETWORK VIDEO RECORDER
User Manual
Wisenet NVR

Copyright
©2023 Hanwha Vision Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of
their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly,
without formal authorization.
Disclaimer
Hanwha Vision makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be
provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Hanwha Vision reserves the right to
change the contents of this document without prior notice.
Design and specications are subject to change without prior notice.
You can download the latest version from the Hanwha Vision web site. (www.HanwhaVision.com)
The initial administrator ID is “admin” and the password should be set when logging in for the rst time.
Please change your password every three months to safely protect personal information and to prevent the damage of the
information theft.
Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.
NETWORK VIDEO RECORDER
User Manual

English _3
● overview
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit.
Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil
constituents as they may deform or cause damage to the product.)
7) Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. if the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
overview
Standards Approvals
`Any changes or modifications in construction of this device which are not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
`This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
`This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
PRODUCT USER MANUAL DESCRIPTION
This document is a user manual for Wisenet Recorder product. Before using this product, please read this document
carefully in order to use it properly.
•This user manual explains how to use the product based on the defaults and default screens of this product.
•The content of this manual is subject to change depending on the product software updates and the company
policies. It is subject to partial changes without prior notification to users.
TARGET AUDIENCE
This user manual contains contents for Wisenet Recorder users.
HOW TO USE THE PRODUCT
Users of this product can perform the following:
•Monitor cameras registered to Wisenet Recorder in real time
•Search for or play videos saved in Wisenet Recorder
•Monitor text data being transmitted to the POS device connected to Wisenet Recorder in real time
•Search for text data from the POS device connected to Wisenet Recorder
•Monitor real time events that occur in Wisenet Recorder, sensors, and cameras or search through logs
Before using this product, check if the latest version of this software is installed. Go to Hanwha Vision's website
(http://www.HanwhaVision.com) to check the software version and download necessary files.

4_ overview
overview
CONTENTS
OVERVIEW
3
3Important Safety Instructions
3Product User Manual Description
3Target Audience
3How to Use the Product
4Contents
LIVE
5
5Getting Started
8Live Screen Configuration
11 Live Screen Mode
12 Status
15 Zoom
15 Layout
16 Audio ON/OFF
16 Freeze
16 Event Monitoring
17 Capture
17 Maintain the Screen Ratio
18 Display Text
18 PTZ control
19 Backup
MENU SETUP
21
21 System Setup
27 Setting the Camera
35 Setting the Device
39 Setting the Recording
41 Setting the Event
44 Network Configuration
SEARCH & PLAY
51
51 Search
54 Playback
STARTING WEB VIEWER
55
55 What is Web Viewer?
55 Connecting Web Viewer
LIVE VIEWER
56
56 Live Viewer
61 Control of connecting Network Camera
SEARCH VIEWER
62
62 Search viewer
SETUP VIEWER
66
66 Setup Viewer
BACKUP VIEWER
76
76 SEC Backup Viewer
APPENDIX
78
78 Using a remote controller
79 Use Joystick
79 Using Virtual Keyboard
80 Troubleshooting

English _5
● live
GETTING STARTED
Starting the system
1. Connect the power cable of the Recorder to the wall outlet.
2. You will see the initialization screen.
The initialization process will last about 2 minute.
If a new HDD is installed, the initialization process may take longer.
3. The live screen appears with a beep.
The following symptoms might be observed when starting the system.
`If the HDD number is displayed at the bottom of the screen along with < > while the product is booting up, it indicates that
the HDD is in recovery, and for this reason booting up may take longer.
HDD 1, 2
`If the progress stalls while in < > state, it indicates that the HDD has problems. Visit your nearest customer service center to
check the HDD.
HDD 2
live
Install Wizard
As shown below, proceed through each step of the <Install Wizard>.
Install Wizard can only be accessed at factory reset. If you do not want to proceed, click <Cancel>.
1. In the <Language> screen, select the language and press the <Next> button.
2. Set the network connection type and the connection environment on the <Network> screen, and then click
the <Next> button.
Setting up the DHCP server
If you set up the DHCP server, the IP address is automatically assigned to your camera.
For more details, see the "DHCP server" page under "Menu Setup > Network Configuration" in the Table of
Contents.
`Depending on the camera's state, no IP may be automatically assigned to the camera. After exiting the installation wizard, go to
the menu to assign an IP to DHCP, or set the IP manually.
Setting up the network
The network port can be used as a common port for camera and web viewer connection.
•IP type: Allows you to select the type of network access.
•IP address, subnet mask, gateway, DNS
- Static: IP address, subnet mask, gateway, and DNS can be directly entered.
- DHCP: IP address, subnet mask, gateway, and DNS can be automatically set.
- PPPoE: IP address, subnet mask, gateway, and DNS can be automatically set.
•User ID, password: To set the access mode to PPPoE, enter the "User ID" and "Password" registered to
PPPoE.

6_ live
live
3. Set the administrator password on the <Recorder ID/PW> screen and click the <Next> button.
Click < > to view the basic guide for setting a password. Refer to the password setup rules.
4. Set the camera password in factory reset on the <Camera ID/PW> screen.
If ID/PW is already set in the camera, register the ID/PW and click <Next>.
`When the password is in factory reset, it can be changed and managed in a batch.
`Up to 3 sets of camera ID with password and password can be registered.
`You may change the passwords for all registered cameras by navigating to Menu > Camera > Camera Password.
`You cannot change password of a camera registered using ONVIF or RTSP.
5. Set the date, time, time zone, and DST on the <Date/Time> screen, and then click the <Next> button.
`If the LAN cable is not connected to the port, the setting button will not be activated for use. Check the LAN cable connection.
(But in case of a PoE product, Network 1 is activated.)
`The built-in DHCP Server in Recorder will turn on automatically at stage 2. At this stage, using the existing DHCP server in the
same network may cause a problem, as two DHCP servers would be simultaneously operating.
`A product with multiple network ports cannot use a single bandwidth for all of them.
Example)
- Port 1: 192.168.100.199 / Port 2: 192.168.100.198 (X)
- Port 1: 192.168.100.199 / Port 2: 192.168.101.198 (O)
Setting the Switch Mode
Set the camera registration method. This function is only available for products with PoE support.
For products with PoE support, see “Products supporting each feature”. (See page 4 of the Product
Specification Manual)
•PnP Mode : Camera connected to the PoE port of the product will be registered automatically on each
channel in the order of the port number.
- When the camera is factory reset, it defaults to the ID and password set during the <Camera ID/PW>
step.
- If the camera's ID and password have already been set, the registered information matches the ID and
password set during the <Camera ID/PW> step. (up to 3 sets)
If the camera uses a static IP, it can be registered only if it has the identical bandwidth with Network1's IP
bandwidth.
•Manual Setup Mode : Automatically scans and registers camera connected to the product’s PoE and camera
with separate switch.

English _7
● live
6. To set the recommended resolution on the <Resolution> screen, click <Apply> followed by the <Next>
button.
7. On the <Camera register> screen, select a camera to register from the searched camera list and click the
<Register> button. Select a camera to register from the list and click the <Change IP> button.
After completing camera register, click <Next>.
8. On the <Channel Setup> screen, you can view the camera videos registered to each channel in thumbnails
along with thumbnail information. To change the camera video position, select a video and drag and drop it
to the desired location.
9. Click the <Finish> button to complete the Install Wizard.
Shutting Down the System
1. In the live screen menu, select <Shutdown>.
2. The “Shutdown” confirmation pop-up window will appear.
3. Click on <OK>.
The system will shut down.
Restarting the System
1. In the live screen menu, select <Restart>.
2. The “Restart” confirmation pop-up window will appear.
3. Click on <OK>.
The system will restart.
`Only the user with the "Shutdown" or "Restart" permission can shut down or restart the system.
`To manage Permission Setup, see the "User" page under "Menu Setup > System Setup" in the Table of Contents.

8_ live
live
Login
To use the Recorder menu, you are required to login as a user that is authorized to access the applicable menu.
1. Right click with your mouse button on the live mode screen.
You will see the context menu on the screen as shown.
2. Select <Login>.
The login dialog appears.
`The initial administrator ID is set to "admin" and you will need to configure the password in the installation wizard.
`Please change your password every three months to safely protect personal information and to prevent the damage of the
information theft. Please, take note that it’s a user’s responsibility for the security and any other problems caused by
mismanaging a password.
`For more information about limited-access permission, see the "User" page under “Menu Setup > System Setup” in
the Table of Contents.
LIVE SCREEN CONFIGURATION
Icons on the Live Screen
You can check the status or operation with the icons on the live screen.
CAM 01
2019-01-01 00:00:01
FULL NO
CPU
FULL NO
CPU
FULL NO
CPU
FULL NO
CPU
Name Description
a
Current Date, Time Displays the current time and date.
b
Screen Mode
FULL NO RAIDRAID
SCSI
It is displayed when there is ongoing backup in the live condition.
FULL NO RAIDRAID
SCSI
Displayed when manually recording a video while the access restriction for stop recording
is enabled.
Only a user with the permission to stop recording is allowed to stop recording.
FULL NO RAIDRAID
SCSI
It is displayed when all the channels are switched at the set time interval.
FULL NO RAIDRAID
SCSI
This icon is displayed when you press the Freeze button.
FULL NO RAIDRAID
SCSI
It is displayed when the magnifying function is in operation.
c
Login Information When you are logged in, the "LOG ON" icon will be displayed.
d
System
Operation
FULL NO RAIDRAID
SCSI
It is displayed when there is a problem with the fan.
`
Only provided for products that support fans. (See page 4 of the Product Specification
Manual)
FULL NO RAIDRAID
SCSI
Displayed when recording data is not properly saved.
FULL NO RAIDRAID
SCSI
Appears when input data rate per channel exceeds the specified data rate limit.

English _9
● live
Name Description
d
System
Operation
FULL NO RAIDRAID
SCSI
It is displayed when there is firmware to update the server.
FULL NO RAIDRAID
SCSI
It is displayed when the network is overloaded.
`
It occurs when the max receiving allowance is exceeded, causing an overload to the CPU.
It will disappear if you modify the camera settings or delete a camera to reduce the
performance burden.
FULL NO
CPU
Displayed when system overload occurs.
`
Limit the number of users remotely monitored by Web Viewer or VMS, or control the
number of channels played by remote or recorder.
FULL
NO RAIDRAID
SCSI
Displayed if the HDD is full and the Recorder has an insufficient space to record.
FULL
NO
RAIDRAID
SCSI
Displayed when there is no HDD or HDD is not detected.
FULL NO RAIDRAID
SCSI
Displayed if the HDD needs a technical examination.
FULL NO
CPU
Displayed when the camera firmware upgrade is complete. Click to view the results.
e
Video Input
Status
Displayed if no input is entered in the condition that the camera is set to <ON>.
FULL NO RAIDRAID
SCSI
Displayed when the live image with the camera turned <ON> exceeds the supported
resolution.
Displayed if no permission to live view is granted.
If the camera channel is <OFF>, the camera is not registered, or it is set to <Covert2>,
the live screen will display nothing. For <Covert1>, the screen will display nothing but
OSD.
f
Camera Title / Channel Display the camera title and channel number.
g
Camera
Operation
FULL NO
CPU
This icon is displayed for a channel that a PTZ-featuring camera is connected to.
FULL NO
CPU
Displays AUDIO ON/MUTE. Not displayed in video mode if deactivated.
FULL NO
CPU
If the sensor is set to <ON>, the input signal will be displayed on the screen of the
connected channel.
FULL NO
CPU
This icon is displayed when Motion Detection is set to <ON> and a camera motion or
camera event occurs.
/ / It displays the status of general/event/scheduled recording.
FULL NO
CPU
It is displayed when it fails to decode all the frames due to limited decoding performance
and in this case only the I-Frame is decoded.
FULL NO
CPU
This is displayed when a POS (text) event occurs.
FULL NO
CPU
RED - Displayed when there is any abnormality in the RED-SD card.
YELLOW - Displayed when there is no storage space in the SD card.
FULL NO
CPU
/
FULL NO
CPU
Flickers when a defocus event occurs. When you click the icon, a simple focus command
is sent to the camera.
`
Displayed when a fog detection event occurs.
Error Information
•If the built-in HDD is not connected, the “NO HDD” icon ( ) will be displayed in the top left corner. In this
case, make sure you contact the service center for assistance as this may cause a failure of recording,
playback or backup.
•
If you do not format a purchased HDD in a format supporting Recorder, a "NO HDD" icon( ) will be
displayed on the top left side of the screen. If the "NO HDD" icon is displayed, go to "Menu > Storage
Device" to check the HDD connection status, and format your HDD.
•
If a product with a fan does not work or has a problem with the fan, <Fan Information Window> appears and
the fan malfunction icon ( ) is displayed at the top left. In this case, check the fan inside the product. If the
fan is defective, it can shorten the product life cycle, so please make sure to contract service center nearby.
`If an abnormal fan icon ( ) or NO HDD ( ) icon, HDD FAIL (
FULL NO RAIDRAID
SCSI
) icon is displayed, contact our customer service.
`For products that support fan, see page 4 "Products supporting each feature" of the Product Specification Manual.
Live Screen Menu
If you right click with your mouse button in live screen mode, it will launch the live screen menu where you can
access each menu.
The context menu differs depending on the state of Log in/out, split mode, and Recorder operation status.
`Depending on the user permissions, you may have limited access to menu items of Live View, Backup, Stop Recording, Search,
PTZ, Remote Alarm Output, and Exit.
Single Mode Menu
The single mode menu is available only in Single Mode.
Menu Description
PTZ
Accesses the PTZ Control menu. The PTZ menu will be active on the Live screen after you select a
single channel.
For more details, see the "Live > PTZ Control" page in the Table of Contents.
ZOOM You can enlarge the selected screen.
See the "Live > Zoom" page in the Table of Contents.
Capture Captures the screen of the selected channel.
See the "Live > Capture" page in the Table of Contents.

10_ live
live
Split Mode Menu
In Live split mode, right-click to display this context menu as shown.
The look of the split mode menu is different for each Recorder product and it also depends on the login/logout
status.
Menu Description
Layout Select the split mode to display on the live screen.
See the "Live > Live screen mode"page in the Table of Contents.
Layout Setup Set the layout of each channel.
See the "Live > Layout"page in the Table of Contents.
Full aspect ratio/
Channel aspect ratio
Channel screen ratio is changed.
See the "Live > Maintain the Screen Ratio" page in the Table of Contents.
Status
Shows the connection information of camera connected to each channel as well as live and recording
status.
See the "Live > Status" page in the Table of Contents.
`
For product supporting PoE, you can check the PoE status under “PoE Status”.
`
Only provided for products that support PoE. (See page 4 of the Product Specification Manual)
Audio On/Off Turns ON/MUTE the sound of the selected channel.
See the "Live > Audio ON/OFF"page in the Table of Contents.
Freeze Stop playing the video temporarily.
See the "Live > Freeze"page in the Table of Contents.
Stop alarm output Stop the alarm output, deactivate the event icon and release the auto sequencing.
See the "Live > Event Monitoring" page in the Table of Contents.
Record/Record stop Starts or stops manual recording.
Play See the "Search & Play > Play" page in the Table of Contents.
Search See the "Search & Play > Search" page in the Table of Contents.
Menu Description
Backup Searches for a backup device and back up each channel at your desired time.
See the "Live > Backup"page in the Table of Contents.
Menu Enter the main menu.
See the "Menu Setup"page in the Table of Contents.
Shutdown/Restart
The system shutdown/restart dialog will appear.
Login/Logout You can log in or out.
Show Launcher/
Hide Launcher
Shows or hides the launcher. Refer to "View the Launcher Menu".

English _11
● live
View the Launcher Menu
The Launcher menu appears on the bottom of the live screen.
1. Select <Show Launcher> in the context menu of the Live screen.
2. Move the cursor to the bottom and click a desired item in the Launcher menu.
`If no input is entered for 10 seconds, the menu will disappear.
c db mlkjihgfe
a
Menu Description
a
Layout Select the layout to be displayed on the screen.
b
Layout Setup You can set, change or delete the new layout of each channel.
c
Screen Mode Displays a list of split modes available in a bar type.
The current screen mode will be displayed grey.
d
Close Slide/
Open Slide Click to display the hidden menu to the right.
e
Manual Backup Searches for a backup device and back up each channel at your desired time.
f
Zoom In Enlarges the selected area. This is available only in Single Live mode.
g
PTZ Mode If the network camera connected to the selected channel supports the PTZ operations, this will run
the PTZ control launcher.
h
Alarm Stop Stops the alarm if it's activated.
i
Freeze Freezes the Live screen temporarily.
j
Capture Captures the screen of the selected channel.
k
Print Text Text output is ON or OFF.
l
Play Enters Play mode if a file to play exist, and if not, enters Search mode.
m
Manual Record Start/End recording the Live screen.
LIVE SCREEN MODE
You can display your camera's live video in various split modes.
`The ‘Live4NVR’ profile is added automatically with network camera auto registration, and settings can be changed according to user
environment.
`Live4NVR Profile Basic Settings : H.264 (codec), 800 x 600 or 800 x 448 (resolution), 30fps (frame rate)
`Depending on camera specification, you may not be able to add a profile or if you have the PLUGINFREE profile, you will not be able to
add the Live4NVR profile.
`When system overloaded and the performance is down, network camera may play only main frame(I-frame).
`To set profiles, see the "Camera Setting" page under "Menu Setup > Setting the Device".
Method for displaying screen mode
If you want to change the split mode, select a screen mode suggested in the launcher menu or right click with
the mouse button and select a split mode in the screen mode menu.
`Each product may support different split view modes. See page 14 "Product specification"of the Product Specification
Manual.
CH1
CH1
CH2 CH1 CH2 CH1 CH2 CH3
Single mode Horizontal 2-split screen Vertical 2-split screen 3-split mode
CH1 CH2
CH3 CH4
CH2
CH1 CH3
CH4 CH5 CH6
CH2
CH3
CH1 CH4
CH5 CH6 CH7 CH8
CH1 CH2 CH3
CH4 CH5 CH6
CH7 CH8 CH9
4-split mode 6-split mode
(1+5-split mode)
8-split mode
(1+7-split mode)
9-split mode
CH2 CH3 CH4 CH5
CH6 CH7
CH8 CH1 CH9
CH10 CH11 CH12 CH13
CH1 CH2 CH3 CH4
CH5 CH6 CH7 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16 CH1
13-split mode
(1+12-split mode)
16-split mode Auto Sequence

12_ live
live
Switching the split mode
You can split the live video from cameras to Single, 4-split, 9-Split, or 16-split mode and watch them one by one.
`Each product supports different split modes. For more information, see "Method for displaying screen mode".
Press the button in the launcher or use the right menu to automatically switch the screen.
Mouse right button menu ;Layout ;Auto switching mode
Auto Sequence
You can monitor the split mode of your own choice by switching one after another at a certain interval.
`For segmented screen switching, set <Sequence switching time> on the "Monitor" page under "Menu Setup > Setting
the Device" in the Table of Contents to automatically switch to the next sequence according to the preset time.
`When you switch the channel, the video may be delayed depending on the network condition.
Example) LRN-1610S
16
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1
CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
1
Single mode
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
13-16
1-4
4-split mode
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
10-16
1-9
9-split mode
Manual Switching
Click the arrow <
◄
/
►
> key to move to the next split mode.
`If your product supports a remote controller, you can manually press the Left/Right buttons to switch between different screen
modes.
For products that support remote controls, see page 4 “Products supporting each feature”of the Product Specification
Manual)
Example) After setting to 4-split mode in LRN-1610S, if you press the Right [►] button:
Channel(CH 1~4) ;Channel(CH 5~8) ;Channel(CH 9~12) ;Channel(CH 13~16)
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH17 CH18
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH17 CH18
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH17 CH18
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
CH1 CH2
CH3 CH4
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH17 CH18
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH3 CH4 CH5 CH6CH1 CH2
CH9 CH10 CH11 CH12CH7 CH8
CH15 CH16 CH17 CH18CH13 CH14
CH21 CH22 CH23 CH24CH19 CH20
CH27 CH28 CH29 CH30CH25 CH26
CH33 CH34 CH35 CH36CH31 CH32
▶ ▶ ▶
STATUS
You can check the connection information of the camera to be connected to each channel on the live screen.
Channel info
Right-click on the live screen and select <CH Info> in the <Status> menu to display the information on the
current video in overlay over the live video being monitored.
`ARB is only displayed when an ARB situation occurs.
`The letters shown next to the product name represents the protocol used to register the camera.
-S and V represent Wisenet protocol while O represents ONVIF.
-If connected using the RTSP protocol, then only RTSP is displayed without any product name.
RES : 1920x1080 (H.264)
SET/IN/DEC : 30/30/30.0
RES : 1920x1080 (H.264)
SET/IN/DEC : 30/30/30.0

English _13
● live
Connection Status
Right-click on the live screen and select <Connection> in the <Status> menu to check the status of cameras
connected to each channel.
Live Status
Right-click on the live screen and select <Live> in the <Status> menu to check the transmitted data from a
network camera connected to each channel.
•Model : Displays the model name of camera connected to each channel.
•Status : Shows the connection status of camera set to each channel.
•IP Address : Displays the IP address of a camera set to each channel.
•Codec : Displays the live profile codec information for a camera set to each channel.
•Resolution : Displays the live profile resolution of a camera set to each channel.
•Frame Rate : Displays the live profile transmission rate for a camera set to each channel.
Record Status
Right-click on the live screen and select <Record> in the <Status> menu to check each channel's profile,
record type, input/recording frame count, allowed/input/recorded amount of data.
•Total Bitrate (Record/Max) : Record bitrate shows the amount of actual data recording while Total bitrate
shows the maximum data transfer allowed by the Recorder.
•Profile : Shows the video profile configured to each channel.
•Frame rate (fps) : Show the input/record frames per second for each channel.
•Bitrate (bps)
- Limit / Input / Record : Shows the amount of limit/input/recording data for each channel.
- Receive/Limit : Shows the data ratio of actual data transferred from the camera and allowed maximum
defined by user.
•Current : Shows the recording status information of currently transferred data.
•Max : Shows recording information of the most biggest recording data out of configured standard and event
recordings.
•: Reloads the recording information.
•Record Setup : The menu screen will switch to the record setting screen.
`
If an error occurs during recording, the channel's profile column turns yellow.
This profile error indicates that when a recording profile cannot be used to receive video from camera, an alternative profile is used to record the video.
When the recording profile resumes, the camera video can record by using the set recording profile.
`
If Recorder exceeds the recording limit, only the key frame will be recorded. In that case, a restricted recording popup and an icon will appear. The
restricted recording popup appears only once. If you change the camera setup and record setup, the restricted recording popup may appear once more to
confirm the status. If you don't want to see it again, then check Do not show this again in the popup.
For the maximum allowed number of recoding, see the "Record Setup" page under "Menu Setup> Setting the Recording" in the Table of Contents.
`
For dual recording, the bit rate is shown as the sum of Main Stream and Sub Stream.
However, the <Enable dual recording> box in the "Record > Record Option" menu must be checked. The recording profile
and remote profile can be set in the "Camera > Profile" menu.

14_ live
live
Network Status
Right-click on the live screen and select <Network> in the <Status> menu to check the status of network
bandwidth currently being received/transmitted.
PoE Status
This function is only available for products that support PoE. For products with PoE support, see “Products
supporting each feature”. (See page 4 of the Product Specification Manual)
Right-click on the live screen and select <PoE> in the <Status> menu to check the current PoE status of each
port.
•Consumption(W) : Displays the power consumption in PoE.
- 0 : No device is connected to the port or a device is using its own power supply.
- –: Trouble in the port (More detailed trouble information can be displayed in additional information.)
`For more information on the whole full PoE power specs of each product, see "Product Specification Manual”. If the power
limits of all ports exceed the PoE specification, each port will be powered down one by one.
•PoE : Turns on/off the power supply to the camera.
If checked, it means the power supply is On; if not checked, it means it is Off.
•Additional information : If there is a problem in the power supply, it is explained here.
Power supply problems include excessive power (class 1 to 4) and voltage errors.
•Total PoE power consumption : Display the sum of power consumption for all the ports.
Channel Setting
You can display the channel in a desired area of a split screen.
1. Place the cursor over the camera name of each channel to display the <
▼
> key to the right on the screen.
2. Click a camera name to display a channel list where you can select a different channel.
3. Select a desired channel and click it.
The current channel will be switched to the selected one.
`Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also change the channel
position.
Example) If switching CH 1 to CH 7
CH1
CH1
CH1
CH1
CH2
CH1
CH2
CH6
CH8
CH10 CH11 CH12 CH13
CH3 CH4 CH5
CH7
CH9
CH1
CH5 CH6 CH7 CH8
CH2
CH3
CH4
CH2
CH3
CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH4 CH5 CH6
CH7 CH8 CH9
CH1 CH2 CH3 CH4
CH5 CH6 CH7 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16
CH1
CH1
CH1
CH1 CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH7 CH8 CH9
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH10 CH11 CH12
CH13 CH14 CH15
CH16
CH7 CH2 CH3 CH4
CH5 CH6 CH1 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16 CH3 CH1
CH1 CH2
CH1 CH2
CH3 CH4
CH1
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH1
CH1
CH1
CH1
CH2
CH1
CH2
CH6
CH8
CH10 CH11 CH12 CH13
CH3 CH4 CH5
CH7
CH9
CH1
CH5 CH6 CH7 CH8
CH2
CH3
CH4
CH2
CH3
CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH4 CH5 CH6
CH7 CH8 CH9
CH1 CH2 CH3 CH4
CH5 CH6 CH7 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16
CH1
CH1
CH1
CH1 CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH7 CH8 CH9
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH10 CH11 CH12
CH13 CH14 CH15
CH16
CH7 CH2 CH3 CH4
CH5 CH6 CH1 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16 CH3 CH1
CH1 CH2
CH1 CH2
CH3 CH4
CH1
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
;
Switching to Single Mode
When in split mode, select and double-click a desired channel to switch to its Single mod.
`If your product supports a remote controller, press the number button for the desired channel on the remote controller to switch
to a single screen.
For more information, see "Using a remote controller > Using the Numeric buttons".
`This function is only available for products that support the use of a remote controller. For products that support remote
controls, see page 4 “Products supporting each feature” of the Product Specification Manual.
Example) If double-clicking CH 3.
CH1
CH1
CH1
CH1
CH2
CH1
CH2
CH6
CH8
CH10 CH11 CH12 CH13
CH3 CH4 CH5
CH7
CH9
CH1
CH5 CH6 CH7 CH8
CH2
CH3
CH4
CH2
CH3
CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH4 CH5 CH6
CH7 CH8 CH9
CH1 CH2 CH3 CH4
CH5 CH6 CH7 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16
CH1
CH1
CH1
CH1 CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH7 CH8 CH9
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH10 CH11 CH12
CH13 CH14 CH15
CH16
CH7 CH2 CH3 CH4
CH5 CH6 CH1 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16 CH3 CH1
CH1 CH2
CH1 CH2
CH3 CH4
CH1
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH1
CH1
CH1
CH1
CH2
CH1
CH2
CH6
CH8
CH10 CH11 CH12 CH13
CH3 CH4 CH5
CH7
CH9
CH1
CH5 CH6 CH7 CH8
CH2
CH3
CH4
CH2
CH3
CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH4 CH5 CH6
CH7 CH8 CH9
CH1 CH2 CH3 CH4
CH5 CH6 CH7 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16
CH1
CH1
CH1
CH1 CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH7 CH8 CH9
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH10 CH11 CH12
CH13 CH14 CH15
CH16
CH7 CH2 CH3 CH4
CH5 CH6 CH1 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16 CH3 CH1
CH1 CH2
CH1 CH2
CH3 CH4
CH1
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3
CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
;

English _15
● live
ZOOM
This is activated only in Live Single mode.
1. After right-clicking on the live screen, click <ZOOM>.
You can also press the [ZOOM] button on your remote controller or click < > in the launcher menu.The Zoom
in icon will appear at the bottom right.
2. Click < > icons to magnify the selected area.
By adjusting the box at the bottom, you can adjust the position of the magnified screen.
3. Click < > icons to zoom out the selected area.
4. Click < > at the top right to close zoom.
If your product supports a remote controller, follow these steps to zoom in on the video screen:
1. Press the [ZOOM] button on your remote controller.
2. Press the four directional keys (▲▼◄►) to designate an area to zoom in.
3. In the selected area, press the [ENTER] button on your remote controller. The selected area can be magnified up
to 10 times.
4. If you want to close the zoom, then press the [ZOOM] button on your remote controller.
`For products that support remote controls, see page 4 “Products supporting each feature” of the Product Specification Manual.
LAYOUT
In the live screen, you can set the layout for each channel.
Setting Up the Live Layout
This section outlines how to select a series of channels based on their purpose/accessibility and monitor them
in a single layout.
Example) Layout "Lobby" - Lobby camera 1, Lobby camera 2, Front entrance camera 2
Layout "VIP" - Directors' meeting room 1, Directors' meeting room 2, Directors' lounge 1, Corridor camera on
the 7th floor
def
c
a
b
g
To create a new layout, follow these steps:
aOpen the channel layout setup menu.
bClick <New>.
cEnter a name for the selected channels (e.g., Parking lot).
dSelect the channels that you want to add to the layout (e.g., 1, 2, 3, 4).
eChoose a split mode to apply (e.g., 4-way split).
fClick <OK>.
gChoose a layout to view it on the screen (e.g., change to Parking lot).
1. Select the < >.
The layout setting screen will appear.
•New : You can set the new layout.
•Rename : You can make changes to the selected layout.
When the layout is changed, the channel order is initialized.
•Delete : You can delete the selected layout.
•Channel Table : You can select channels in the table to be registered in, or removed from the layout.
•Channel List : You can select channels in the list to be registered in, or removed from the layout.
2. Press the <New> button and enter the name of layout to add.
3. In the channel table or channel list, click and select the channel to be displayed on the layout screen.
4. Click on <OK> to save the selected layout.
`The layout for each user is saved separately.
`You can use a configured layout even in the Search Time function to facilitate search using the channel sequence and
combination that you have set.
See the "Time Search" page under "Search & Play > Search" in the Table of Contents

16_ live
live
AUDIO ON/OFF
You can turn the sound on/off corresponding to the channel in Live mode.
AUDIO ON/OFF in Single mode
Click on the audio icon ( ) on the screen to turn it ON/OFF.
`If you have configured the audio output settings properly but the audio or voice is not output, check if the connected network
camera supports the sound signal and if you have configured the sound settings as appropriate. The sound icon can be
displayed if the sound signal fails to output from noise.
`Only the channel where <Audio> is set to <On> in "Camera > Channel Setup" displays the audio icon ( ) in Live mode
that you can use to turn the sound on/off.
FREEZE
This is available only in Live mode, this pauses playing the Live image temporarily.
1. Click < > of the launcher mode.
Video playing is paused.
2. Click on < >.
Pause is canceled. Playing is resumed.
`If your product supports a remote controller, you can press the [FREEZE] button to pause the video.
For products that support remote controls, see page 4 “Products supporting each feature” of the Product Specification Manual.
EVENT MONITORING
This will display the channel in sync with a specific event (Sensor/Motion/Video Loss) if it occurs.
To use the event monitoring function, you should set the <Event Display> by referring to the "Monitor" page in the
table of contents "Menu Setup > Setting the Device".
•If multiple events occur simultaneously, the screen will switch to a split mode.
- 2 ~ 4 events : 4-split mode
- 5 ~ 9 events : 9-split mode
- 10 ~ 16 events : 16-split mode
•If the second event occurs within the set time of <Event Display>, the first event will last until the second one is
terminated.
Example1)
`If you set <Event Display> to 5 seconds, and only one event occurs in CH 1.
CH1
CH1
CH1
CH1
CH2
CH1
CH2
CH6
CH8
CH10 CH11 CH12 CH13
CH3 CH4 CH5
CH7
CH9
CH1
CH5 CH6 CH7 CH8
CH2
CH3
CH4
CH2
CH3
CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH4 CH5 CH6
CH7 CH8 CH9
CH1 CH2 CH3 CH4
CH5 CH6 CH7 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16
CH1
CH1
CH1
CH1 CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH7 CH8 CH9
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH10 CH11 CH12
CH13 CH14 CH15
CH16
CH7 CH2 CH3 CH4
CH5 CH6 CH1 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16 CH3 CH1
CH1 CH2
CH1 CH2
CH3 CH4
CH1
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3
CH1
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
Event occurrence 5 seconds
Stop alarm
Example2)
`If you set <Event Display> to 5 seconds, and the second event occurs in CH 2 within the set time after the first
event occurred in CH 1.
CH1
CH1
CH1
CH1
CH2
CH1
CH2
CH6
CH8
CH10 CH11 CH12 CH13
CH3 CH4 CH5
CH7
CH9
CH1
CH5 CH6 CH7 CH8
CH2
CH3
CH4
CH2
CH3
CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH4 CH5 CH6
CH7 CH8 CH9
CH1 CH2 CH3 CH4
CH5 CH6 CH7 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16
CH1
CH1
CH1
CH1 CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH7 CH8 CH9
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH10 CH11 CH12
CH13 CH14 CH15
CH16
CH7 CH2 CH3 CH4
CH5 CH6 CH1 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16 CH3 CH1
CH1 CH2
CH1 CH2
CH3 CH4
CH1
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3 CH1CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
CH1
CH1
CH1
CH1
CH2
CH1
CH2
CH6
CH8
CH10 CH11 CH12 CH13
CH3 CH4 CH5
CH7
CH9
CH1
CH5 CH6 CH7 CH8
CH2
CH3
CH4
CH2
CH3
CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH4 CH5 CH6
CH7 CH8 CH9
CH1 CH2 CH3 CH4
CH5 CH6 CH7 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16
CH1
CH1
CH1
CH1 CH2
CH3 CH4
CH2 CH3
CH4 CH5 CH6
CH7 CH8 CH9
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH10 CH11 CH12
CH13 CH14 CH15
CH16
CH7 CH2 CH3 CH4
CH5 CH6 CH1 CH8
CH9 CH10 CH11 CH12
CH13 CH14 CH15 CH16 CH3 CH1
CH1 CH2
CH1 CH2
CH3 CH4
CH1
CH1CH7 CH8
CH4
CH3
CH2
CH5
CH1
CH6 CH12
CH1
CH13
CH19
CH4
CH7
CH5
CH10
CH8
CH11
CH6
CH2 CH3
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
CH9 CH10
CH11 CH12
CH13 CH14
CH15 CH16
CH1
CH4 CH5
CH2
CH6
CH1 CH3
CH7 CH8 CH9
CH13 CH14
CH11
CH15
CH10 CH12
CH16
CH1 CH3
CH2
CH4 CH5 CH6
CH1
CH2
CH1 CH2
CH3
CH1
CH15
CH11
CH16
CH12
CH7
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH1
CH6
CH2
CH15
CH11
CH16
CH12
CH1
CH3
CH8
CH4
CH13
CH9
CH14
CH10
CH5
CH7
CH6
CH2
Event occurrence 4 seconds 9 seconds
Stop alarm

English _17
● live
`Select <Alarm Stop> to initialize the status of alarm output and release the event function.
`If your product supports a remote controller, then press the [ALARM] button to reset the alarm output status.
For products that support remote controls, see page 4 “Products supporting each feature” of the Product Specification
Manual.
`If an alarm is output with the pre-event and post-event times specified together with the event recording settings, the event
recording will perform according to the specified recording type (pre event or post event).
`In case of continuous events such as motion detection, switching to another split mode display may not immediate if
concatenating events follow, even when you stopped alarm of the event.
`The video may be delayed depending on the network condition.
`The event output can be delayed as the transfer of the alarm event from the network camera takes time.
CAPTURE
You can capture a screen selected on the live screen.
Function to perform in single channel mode on the live screen or when selecting a channel.
1. Right-click on the live screen and select <Capture>.
You can click on < > in the launcher menu.
2. Select the output information to be displayed on the captured screen.
`If the <Description> box is checked, the description field will be enabled where you can enter up to 50 Korean letters.
3. Select a device to save a captured file, file path and file name.
4. Complete the settings and click <OK>, then the image captured from the screen is saved to the selected device.
`Camera screen larger than 2 megapixels is captured in Full HD size. (LRN-410S/LRN-810S)
MAINTAIN THE SCREEN RATIO
The screen ratio for a live video can be changed.
Maintain a screen ratio for all channels
Video screen ratio for all channels can be changed in live split screen mode.
1. Right-click on the live screen and select <Full aspect ratio>.
The screen ratio for all channels will be changed.
2. If you want to go back to the previous screen ratio, check the menu option for <Full aspect ratio>.
;
Maintain a channel screen ratio
If you select a channel from a live single screen or split screen, you can change its video screen ratio.
1. Right-click on the live screen and select <Channel aspect ratio>.
The screen ratio of a specified channel will be changed.
2. If you want to go back to a previous screen ratio, select <Channel aspect ratio> again.
;

18_ live
live
DISPLAY TEXT
You can monitor texts regarding the sales record received from POS in real time.
Change text output
The Recorder can display text on a live screen when a text device is set.
Select text output
This is executable when a text device is connected.
•How to turn the text output off : Select "OFF" from the text list.
•
How to display on other devices differently from the preset device : Select a device to display from the text list.
Onions 3.59
CHIP 2.37
Apple 2.69
Goat 0.79
Cheese 0.69
Onions 1.58
Peppers red, loose 0.59
2 x 0.79 1.18
Pasta 0.59
2 x 0.59 1.18
========================
TOTAL 3.63
TEXT 01
Onions 3.59
CHIP 2.37
Apple 2.69
Goat 0.79
Cheese 0.69
Onions 1.58
Peppers red, loose 0.59
2 x 0.79 1.18
OK
TEXT 01
PTZ CONTROL
With this Recorder, you can configure the settings of a PTZ camera as well as commercial cameras in the market to
your preference.
PTZ device
This is active only if a channel that a PTZ camera is connected to is selected.
Getting started with PTZ operations
The PTZ camera will be activated only if the channel of the PTZ camera is selected, which can be performed in
the following way:
•Using the launcher menu : Click < > from the launcher menu of the Live screen.
•Using the Live screen menu : Select <PTZ> in the context menu of the Live screen.
•Using the icons on the Live screen : Simply click the < > icon on the Live screen.
`This is available only if a PTZ camera is connected and the < > icon is displayed on the screen.
`Even if the connected network camera does not support the PTZ operations, you can configure the PTZ control settings (if
possible) by installing the PTZ driver (physical device).
`It supports only the Hanwha Vision PTZ function network camera and ONVIF registration network camera.
Using the PTZ camera
You can use a single PTZ camera to perform the Pan, Tilt and Zoom operations to monitor multiple places, and
configure the custom settings of the presets in a desired mode.
1. Open the <PTZ Control> menu.
The < > icon in the left bottom of the screen will turn yellow, indicating that the system accesses "PTZ
Control" mode. You will see the "PTZ Control" launcher menu.
`The PTZ working (active) mark can be active even if the PTZ operation is not available in normal mode. So ensure that you have
completed the PTZ settings before proceeding.
2. Use the PTZ Wheel in the launch menu to adjust the location of recording by a camera.
•Sensitivity : Adjust sensitivity for Pan, Tilt controls.
•PTZ Wheel : Click a near area from the center to move the camera lens slowly; clicking a far area will move it
fast.
`If clicking and holding the mouse in the left will turn the camera counterclockwise; if clicking and holding the mouse in the right will
move the camera lens clockwise.
•Zoom : Activate the Zoom operation of the PTZ camera.
•Iris : Adjust the amount of light incoming to the camera.
•Focus : You can adjust the focus manually.
•Swing : Swing is a monitoring function that moves between two preset points and enables you to trace the
motion.
•Group : The group function enables you to group various presets before calling them in sequence.
•Trace : Tracking remembers the trace of movements that you instructed and reproduces it for your reference.
•Tour : Monitor all the groups created by a user in turn.
`Some cameras may differ in the menu title and operation with regard to Swing, Group, Tour and Trace.
`Even if your network camera supports the function, you can use it only if the button is activated in the PTZ control launcher.
`If your product supports a remote controller, then press the four directional keys (▲▼◄►) to control PTZ.
For products that support remote controls, see page 4 “Products supporting each feature” of the Product Specification
Manual.

English _19
● live
Using Digital PTZ (D-PTZ) function
1. Register a camera that supports the D-PTZ profile.
`In cameras that support the D-PTZ profile, you can use the D-PTZ function.
2. Both cameras that support general PTZ and cameras that support D-PTZ can control the live image using
some of the <PTZ control> function menus.
`For more information about the supported functions, please refer to the camera manual.
Preset
Preset is a set of saved data specifying the locations of a PTZ camera. A single PTZ camera can save up to
300 locations.
To add a preset
1. Check the preset checkbox.
2. Select < >.
The virtual keyboard will appear on the screen. Use it to provide the preset name.
`See "Using virtual keyboard" in the Appendix.
•: You can change the preset settings to your preference.
•: Delete a selected preset.
•: Delete all the existing preset settings.
`If you replace a camera that saves your preset settings with a different one, you must configure the preset settings again.
3. Select <OK>.
The preset setting will be saved in the provided name.
To change or delete a registered preset
1. Check the preset checkbox and select a preset to change or delete.
2. Press < > or < > as needed.
•: Delete all the existing preset settings.
`Deleting all presets might delete even the default preset from the network camera.
3. Provide a new name and press <OK>.
BACKUP
You can search for a backup device and back up video recording at your desired time for each layout or channel.
;
1. Right-click on the live screen and select <Backup>.
You can click on < > in the launcher menu.
`If your product supports a remote controller, then press the [BACKUP] button to go to the Backup menu.
For products that support remote controls, see page 4 “Products supporting each feature” of the Product Specification
Manual.
2. The backup settings screen will be opened.
•Select a layout. : Select a desired layout from the layout list.
•Channel : Sets the channel to backup.
`You can select multiple channels.
If you select <All>, all channels will be selected.

20_ live
live
•Backup Range : Sets the <Start> and <End> time for the backup.
- Start time : Set the backup start time to your desired time.
If you click the [Start] button, the Backup start time is set to the starting time of the last video recording.
However, the Start time will not be displayed on the screen. If you click the [Start] button once more, the
Backup start time is set to the time set by user.
- End : You can set the Backup end time to your desired time.
If you click the [End] button, the Backup end time is set to the ending time of the last video recording.
However, the End time will not be displayed on the screen. If you click the [End] button once more, the
Backup end time is set to the time set by user.
•Overlapped Data : Shows a list of overlapping data on a same time according to the number of data.
This is displayed when there are duplicate data in the same channel due to changes in the time or time zone.
`See the "Setting the Date/Time/Language" page under "Menu Setup > System Setup" in the Table of Contents.
•Device : Select a backup device from the recognized devices.
•Type : Sets the backup data format.
- SEC : SEC is a proprietary file format, which can be played on the PC immediately as it is backed up with a
dedicated viewer.
- Recorder : Saved data can be played back only by the Recorder.
`When you select the SEC format, you can select or deselect "Password" and "Text data included".
•Path : displays the location of the folder in which the backup file is to be saved.
•Check capacity : Shows the size of the selected backup data, used and available capacity of the selected
backup device.
3. When the backup setup is done, press <Start>.
`If there is no device to back up, the <Start> button is disabled.
`If you insert a USB memory stick with insufficient storage space, volume calculation may be disabled.
Format the memory stick or delete some of the data on the memory stick to secure adequate storage space.
`The application may slow down during the backup.
`You can switch to the menu screen during the backup in operation, but playback of data is not available.
`The data can be played back on a Webviewer while the backup is in progress but audio does not function.
`If backup has failed, select “Device > Storage Device” and check the free space of the HDD and check also if the HDD is
properly connected.
`Pressing the <Hide> during the backup will return to the previous menu, while the backup progresses.
Table of contents
Other Hanwha Vision Network Hardware manuals
Popular Network Hardware manuals by other brands

Sierra Monitor Corporation
Sierra Monitor Corporation EX250-SEN1 instruction manual

Quadro
Quadro NMEA Technical manual

Brocade Communications Systems
Brocade Communications Systems RFS4000 Cli reference guide

D-Link
D-Link MYDLINK DNR-322L Quick installation guide

IOCELL
IOCELL NetDISK 351UNE user manual

MICROBEE
MICROBEE PCFW-104-ETH user manual