Haobonder MAI-8525 User manual

MAI-8525 系列工业主板
使用说明书
深圳市华邦德科技有限公司

Chapter 1
Introduction
1.1 Copyright Notice

All Rights Reserved. The information in this document is subject to change
without prior notice in order to improve the reliability, design and function. It
does not represent a commitment on the part of the manufacturer. Under no
circumstances will the manufacturer be liable for any direct, indirect, special,
incidental, or consequential damages arising from the use or inability to use
the product or documentation, even if advised of the possibility of such
damages. This document contains proprietary information protected by
copyright. All rights are reserved. No part of this manual may be reproduced
by any mechanical, electronic, or other means in any form without prior
written permission of the manufacturer.
1.2 About this User's Manual
This User's Manual is intended for experienced users and integrators with
hardware knowledge of personal computers. If you are not sure about any
description in this User's Manual, please consult your vendor before further
handling.
1.3 Warning
Embedded Miniboards and their components contain very delicate
Integrated Circuits (IC). To protect the Embedded Miniboard and its
components against damage from static electricity, you should always follow
the following precautions when handling it :
1. Disconnect your Embedded Miniboard from the power source when you
want to work on the inside.
2. Hold the board by the edges and try not to touch the IC chips, leads or
Circuitry.
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that came
with the Embedded Miniboard, whenever components are separated from
the system.
1.4 Replacing the lithium battery

Incorrect replacement of the lithium battery may lead to a risk of
explosion. The lithium battery must be replaced with an identical
battery or a battery type recommended by the manufacturer. Do not
throw lithium batteries into the trashcan. It must be disposed of in
accordance with local requlations concerning special waste.
1.5 Warranty
This product is warranted to be in good working order for a period of
two years from the date of purchase. Should this product fail to be in
good working order at any time during this period, we will, at our option,
replace or repair it at no additional charge except as set forth in the
following terms. This warranty does not apply to products damaged by
misuse, modifications, accident or disaster.
Vendor assumes no liability for any damages, lost profits, lost savings
or any other incidental or consequential damage resulting from the
use, misuse of, or inability to use this product. Vendor will not be liable
for any claim made by any other related party.
Vendors disclaim all other warranties, either expressed or implied,
including but not limited to implied warranties of merchantibility and
fitness for a particular purpose, with respect to the hardware, the
accompanying product's manual(s) and written materials, and any
accompanying hardware. This limited warranty gives you specific
legal rights.
Return authorization must be obtained from the vendor before
returned merchandise will be accepted. Authorization can be obtained
by calling or faxing the vendor and requesting a Return Merchandise
Authorization (RMA) number. Returned goods should always be
accompanied by a clear problem description.
1.6 Ordering Information

MAI-8525 R1.0/CM600
5.25" Intel ULV Celeron M 600MHz Miniboard with CRT/LCD, LAN,
Audio, PC/104 & PC/104 Plus and DOC Socket
1.7 Specification
Product Name EmCORE-i8527
Form Factor 5.25" Embedded Board Size (203x146mm)
Processor Intel Ultra-Low Voltage Celeron-M FSB 400MHz,
Celeron-M FSB 400MHz,
Low Voltage Pentium-M FSB 400MHz,
Pentium-M FSB 400MHz Processor.
Chipset NB : Intel 852GM SB: Intel ICH4
System Memory On board DDR RAM 256MB (Optional: 512MB Max)
VGA/LCD Controller UMA 852GM AGP Video Controller with LVDS and
CRT support (Support Dual Display, Independent display)
Ethernet Intel 82551QM 10/100 Base-T Fast Ethernet LAN
I/O Chips WINBOUND W83627HF
BIOS Phoenix-Award BIOS version 6.0PG, Support 4MB
Flash ROM
Audio
AC'97 Codec Version: 2.3 supports MIC-In/ Line-In/
Line-out; Optional Stereo Amplifier included (ALC655)
IDE Interface ATA-33 x 1 channel (Support two ATAPI devices)
Compact Flash Disk X 1 (Support up to 2GB)
Serial Port Six COM ports:
COM1,2: RS232/422/485 Selectable
COM3~6: RS-232 (By FinTek F81216D)
Parallel Port Parallel Port Supports SPP/ EPP/ ECP mode
K/B and Mouse Support Standard PS/2 K/B and Mouse
Universal Serial Bus 6 x USB 2.0 Port
Expansion Interface PCI slot, PC/104 and PC/104-plus
Watchdog Timer Chipset Integrated in W83627HF, 1~255 Level (sec or min)
Hardware Monitor Chipset Integrated in W83627HF
RTC Support Real Time Clock
Power Input Connector 2 x 10 Pin ATX (AT power can be used)
Operation Temp. 0 ~ 60°C
* PCI Slot and PC/104-Plus can not be used at the same time, since they
share PCI resource.
1.8 Board Dimensions

Chapter 2
Installation
2.1 Board layout

2.2 Jumpers and Connectors

Jumpers Setting
CMOS Jumper Settings (JBAT1)
Type: Onboard 3-pin header (JBAT1)
Default setting: Keep CMOS
COM1 RS-232 / 422 / 485 Select (JRS1)
Type: Onboard 3-pin header (JCF1)
Default setting:RS-232 mode
COM2 RS-232 / 422 / 485 Select (JRS2)
Type: onboard 6-pin (2*3) header
Default setting: RS-232 mode

COM1 Power Source Special Support (JV1,JV3)
Type: onboard 2*3-pin header
Default setting: Standard
COM2 Power Source Special Support(JV2,JV4)
Type: onboard 2*3-pin header
Default setting: Standard
DOC Address Selects(JDOC1)
Type: onboard 4-pin header
LVDS Panel Voltage Selects (JVLCD1)
Type: onboard 3-pin header
Default setting:3.3V
Connectors

JFRT1

Type: onboard 2.54 pitch 10-pin (2*5) header
Display Connector(VGA1)
Type Onboard 2.0mm 2X8 Pin Box Header
Enhanced IDE Connector(IDE1)

Type onboard 44-pin 2.0mm box headers
LOW PIN CONNECTOR (LPC1)
Type onboard 2*10pin 2.0mm PIN headers
DOC CONNECTOR (DOC1)

Type onboard 2*10pin 2.0mm PIN headers
External SMBus Connector (SMBUS1)
Type: onboard 2.54pitch 3-pin wafer
Floppy Disk Drive Connector (FDD1)
Type: onboard standard 2.00pitch 34-pin (2*17) holes
FAN Connector (CPUF1)

Type: onboard 3-pin wafer connector
FAN Connector (SYSF1)
Type: onboard 3-pin wafer connector
RS-232 Serial Port (COM1)
Type: onboard 2X5-BOX HEADER(2.0mm)
RS-232 Serial Port (COM2)
Type: onboard 2X5BOX HEADER(2.0mm)
RS422/485 Output Connector (JCOM1)
Type: onboard 2.0pitch 4-pin header
RS-422/RS-485 Select by JRS1, share COM1 resource.
RS422/485 Output Connector (JCOM2)

Type: onboard 2.0pitch 4-pin header
RS-422/RS-485 Select by JRS2, share COM2 resource.
PS/2 Keyboard & Mouse Connector (KBM1)
Type: One onboard 2x4pin Header
Parallel Port (LPT1)
Type: onboard 2X13BOX HEADER(2.0mm)
USB Connector (USB1)
Type: onboard 2.54pitch 10-pin header for two USB ports
USB Connector (USB2)

Type: onboard 2.54pitch 10-pin header for two USB ports
USB Connector (USB3)
Type: onboard 2.54pitch 10-pin header for two USB ports
LVDS Panel Inverter Connector (INV1)
Type: onboard 2.0pitch 5-pin wafer
LVDS LCD Connector (LVDS1)
Type: onboard DF13 30-pin header
VDD could be selected by JVLCD1 in +5V or +3.3V
DVI CONNECTOR (TMSDS1)

Type: onboard DF13 20-pin header
Infrared (IR) Connector (IR1)
Type: onboard 2.54pitch 5-pin header
Fast Ethernet Connector (LAN1)
Type: onboard 2.54pitch 10-pin header
LAN LED Indicator (LLED1)
Type :onboard 1*4pin 2mm header
Audio Port (Audio1):
Audio Interface Port
Type: onboard 2*5pin 2.0mm BOX header

Power Connector (ATX1)
Type : onboard 2*10-pin connector
Compact Flash Connector (CFD1)