Harbor Freight Tools 62858 Assembly instructions

Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright©2015 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
Owner’s Manual & Safety Instructions
Vehicle not included.
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
ITEM 62858
10 FT. x 20 FT.
PORTABLE CAR CANOPY
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2015 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
REV 15i

Page 2 For technical questions, please call 1-888-866-5797. Item 62858
Table of Contents
Safety ......................................................... 2
Specifications ............................................. 3
Assembly.................................................... 4
Maintenance............................................... 8
Parts List and Diagram.............................. 10
Warranty .................................................... 12
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
safety goggles with side shields.
Read the manual before
set-up and/or use.
SAFETY MAINTENANCE
ASSEMBLY

Page 3For technical questions, please call 1-888-866-5797.Item 62858
IMPORTANT SAFETY INFORMATION
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in serious injury.
Save all warnings and instructions for future reference.
The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible
conditions and situations that may occur. It must be understood by the operator that common sense
and caution are factors which cannot be built into this product, but must be supplied by the operator.
Assembly Precautions
1. Do not assemble in windy conditions.
2. Assemble and install only on
flat, level, hard surface.
3. Assemble and anchor only according to
these instructions. Improper assembly or
inadequate anchoring can create hazards.
4. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.
5. Keep assembly area clean and well lit.
6. Keep bystanders out of the area during assembly.
7. Do not assemble when tired or when under
the influence of drugs or medication.
8. Product capabilities apply to properly and
completely assembled product only.
Use Precautions
1. Do not use grill or any other type of
fire under cover. Cover may catch fire
if exposed to heat rising from fire.
2. Do not allow snow or debris to
accumulate on this item.
3. Heavy, wet snow or strong wind could cause
damage or sudden collapse. Remove the Cover
when these or similar conditions are expected.
4. This product is not a toy. Do not allow
children to play with or near this item.
5. Use as intended only.
Do not use for long-term shelter.
6. Inspect regularly, tighten all loose hardware and
loose cords, and secure all loosened anchors.
If any parts are damaged, bent, or stretched, they
must be replaced. Hardware may loosen during
normal operation stresses. Loose hardware
or damaged/altered parts will compromise
the structural integrity of this product.
7. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
SAVE THESE INSTRUCTIONS.
Specifications
Center Height 9′ 6″
Side Height 6′ 5″
SAFETYMAINTENANCE ASSEMBLY

Page 4 For technical questions, please call 1-888-866-5797. Item 62858
Assembly
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY:
Do not leave this product partially assembled. Assemble this product completely at one time.
Note: For additional information regarding the parts listed in the following pages,
refer to Parts List and Diagram on page 10.
Note: Much of this product’s assembly is done using slip fit construction. Make sure all parts seat completely
and securely. A rubber mallet (sold separately) can be used to gently tap parts in place to ensure a tight fit.
Figure 1: Roof Assembly - 1
5
2
242
3
3
32
2
25
2
4
2
6
6
2
4
5
5
2
4
2
1. Assemble one half of the roof using 11x Swaged Tubes (2), 3x Rafter Tubes (3),
4x Straight Cross Tubes (4), 4x 3-Way Connectors (5), and 2x 4-Way Connectors (6).
Align the 3- and 4-Way Connectors so that the free ends are all on the
same side of the assembly, as shown in Figure 1.
Figure 2: Roof Assembly - 2
524262425
5
6
5
3
3
3
22
2
2. Connect a Swaged Tube (2) to each 3- and 4-Way Connector (5,6) at the top of the roof.
Connect a Rafter Tube (3) to the end of each Swaged Tube (2).
Connect 4x Swaged Tubes (2), 2x Straight Cross Tubes (4), 2x 3-Way Connectors (5), and
1x 4-Way Connector (6) together, then attach that assembly to the ends of the Rafter Tubes (3).
SAFETY MAINTENANCE
ASSEMBLY

Page 5For technical questions, please call 1-888-866-5797.Item 62858
Figure 3: Roof Tarp (9)
9
eyelet
straps
3. Place the Roof Tarp (9) over the top of the roof assembly with its eyelet straps facing down, on the inside.
Figure 4: Connecting Ball Tie-downs (10)
4. Use the Ball Tie-downs (10) to attach the Roof Tarp to the tubes using the eyelets on the eyelet straps.
Figure 5: Leg Assembly - 1
1
2
1
2
1
2
5
6
5
WARNING
Topreventserious
injury,
propertydamage,
andcollapse:
1.DONOTUSEIN
HIGH
WIND.
Remove
coverifharshweather
orheavyrainthreatens.
2.Donotallowsno
w,
rainwate
r,ordebris
toaccumulateor
poolonshelte
r.
3.Anchorsecurelytoflat,
level,solidsurfaceable
tosupportshelterand
vehicleaccordingto
manualinstructions.
4.Inspectbeforeassembly
andeveryuse;donot
assembleoruseifparts
looseordamaged.
5.W
earANSI-approved
safetygoggles,
heavy
-dutywork
gloves,
andhardhatduring
assemblyandservice.
6.Readmanualbefore
assemblyand/oruse.
MadeinChina.
12a ITEM
69034
DONOTREMOVE.
10ft.x 20 ft.
Portable
CarCanopy
warning
label
5. Attach a Straight Tube (1) to each 3- and 4-Way Connector (5, 6) on one side of the assembly.
Note: The warning label is on one of the Straight Tubes (1).
Turn that Tube so that the Warning label can be read easily.
Attach a Swaged Tube (2) to the bottom of each Straight Tube.
SAFETYMAINTENANCE ASSEMBLY

Page 6 For technical questions, please call 1-888-866-5797. Item 62858
1
2
1
2
1
2
5
6
5
Figure 6: Leg Assembly - 2
6. Attach a Straight Tube (1) to each 3- and 4-Way Connector (5, 6) on the other side of the assembly.
Attach a Swaged Tube (2) to the bottom of each Straight Tube.
8
7
8
7
8
7
8
7
8
7
8
7
Figure 7: Foot Plate (8) Assembly
7. Place a Foot Plate (8) over the bottom of each Swaged Tube (2).
Use two Base Fastening Stakes (7) through each Foot Plate to anchor the Canopy.
Note: Verify that there are no utility lines nearby before driving anchors.
SAFETY MAINTENANCE
ASSEMBLY

Page 7For technical questions, please call 1-888-866-5797.Item 62858
Figure 8: Securing Tarp Corner Hook (11)
ab
11
8. For each corner of the Roof Tarp (9)
a. Connect the Tarp Corner Hook (11) to the hole on the inside corner of the Straight Tube (1).
b. Pull the end of the Rope snug and tie it off.
Figure 9: Rope Fastening Stakes (12)
9. Drive a Rope Fastening Stake (12) about 3 feet away from each corner of the canopy, angled inward.
Tie a Rope (13) around the 3-Way Connector (5) at each corner of the Canopy, then attach it to the Stake (12).
Note: Verify that there are no utility lines nearby before driving anchors.
SAFETYMAINTENANCE ASSEMBLY

Page 8 For technical questions, please call 1-888-866-5797. Item 62858
Maintenance
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM PRODUCT FAILURE:
Do not use damaged products. If damage is noted, have the problem corrected before further use.
MONTHLY, inspect the general condition of the Portable Garage. Check for:
• loose ratchet tie downs, anchors, tube connections, and rail clamps (tighten as needed),
• torn or frayed covers, ropes, or cables,
• cracked, bent, or broken parts, and
• any other condition that may affect its safe operation.
SAFETY MAINTENANCE
ASSEMBLY

Page 9For technical questions, please call 1-888-866-5797.Item 62858
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
SAFETYMAINTENANCE ASSEMBLY

Page 10 For technical questions, please call 1-888-866-5797. Item 62858
Parts List and Diagram
Parts List
Note: Individual part illustrations not to scale.
Part Description Illustration Qty
139″ Straight Tube 6
240 1/4″ Swaged Tube 24
324″ Rafter Tube 6
440 5/8″ Straight Cross Tube 6
5 3-Way Connector 6
6 4-Way Connector 3
7 Base Fastening Stake 12
8 Foot Plate 6
9Roof Tarp 1
10 Ball Tie-down 26
11 Tarp Corner Rope and Hook 4
12 Rope Fastening Stake 4
13 Rope 4
SAFETY MAINTENANCE
ASSEMBLY

Page 11For technical questions, please call 1-888-866-5797.Item 62858
Assembly Diagram
11
9
10
1
5
2
8
7
2
242
3
2
5
2
4
2
6
2
4
52
4
2
1
2
2
12
2
2
1
2
1
5242624
3
2
1
2
1
5
SAFETYMAINTENANCE ASSEMBLY

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.