Harman Kardon AVR 435 User manual

Thank you for purchasing a Harman Kardon AVR 435. This Quick-Start
Guide will help you with a basic system installation. For detailed information
on any step, please refer to the Owner’s Manual pages referenced in this
guide. We strongly recommend that you read the Owner’s Manual for
complete details on how to install, configure and operate the AVR 435,
as well as for the important safety information it contains.
Figure 1 – Speaker Placement
The colors shown for each speaker correspond to
the matching output terminal connection on the
back of the AVR 435 (see page 8).
FRONT
LEFT
SPEAKER

(White)
SURROUND 
BACK
LEFT
SPEAKER
(Brown)
SURROUND 
BACK
RIGHT
SPEAKER
(Tan)
CENTER
SPEAKER
(Green)
SUBWOOFER
(Purple)
SURROUND
LEFT
SPEAKER

(Blue)
FRONT
RIGHT
SPEAKER

(Red)
SURROUND
RIGHT
SPEAKER

(Gray)
Step 1. Place your speakers in the listening
room (see page 19).
SPEAKER PLACEMENT
AVR 435 QUICK-START GUIDE
Connections Color Guide
Audio Connections Left Right
Front
Center
Surround
Subwoofer
Surround Back
Digital Audio Connections
Coaxial
Optical
Video Connections
Composite
S-Video
Match the colored jacks on the AVR 435 to the appropriate
jacks on your source equipment or speakers. The colors are
standardized, but not all equipment or connectors use them.

Step 2. Connect the speakers to the receiver: red (+) on speaker to colored (+) on receiver and black (–) to black (–)
(see page 16).
Step 3. Connect the Subwoofer Pre-Out jack to the Line-In jack on your subwoofer.
You may adjust the settings on the subwoofer later as needed (see page 16).
Figure 3 – How to Use the Binding-Post
Speaker Terminal
SURROUND BACK
LEFT SPEAKER
SURROUND BACK
RIGHT SPEAKER
FRONT RIGHT 
SPEAKER FRONT LEFT
SPEAKER CENTER SPEAKER
SUBWOOFER
+
_
+
_
LINE IN/SUB/LFE
+
_
SURROUND
RIGHT SPEAKER
+
_
+
_
+
_
SURROUND
LEFT SPEAKER
+
_
Figure 2 – Speaker Connections
AVR 435 QUICK-START GUIDE

SPEAKER AND AUDIO CONNECTIONS
CD PLAYERAM AntennaFM Antenna
L R Optical Coax
REC/IN

PLAY/OUT
AUDIO RECORDER
Step 4. Connect AM and FM antennas (Fig. 4) (see page 16).
Step 5. Connect source components, as shown in Figures 4 and 5, and
the Device Connection Options chart on the back of this guide (see
pages 16–17).
AUDIO connections: Right channel (red) on source to right (red)
on AVR, and left channel (white) on source to left (white) on AVR.
DIGITAL AUDIO connections, if available: Choose either coaxial
(orange) to coaxial (orange) OR optical to optical for each device.
The Coaxial 1 input defaults to the DVD player;however,it may be
reassigned. Assign the other digital inputs and outputs as appropriate
for your equipment (see Step 7).
VIDEO connections: Choose component (Y/Pb/Pr – green/blue/
red), composite (yellow) or S-video (4-pin) for each video source.
The DVD Component Video inputs default to the DVD player, but may
be reassigned. Connect the component, composite and S-video
Monitor outputs to your Video Monitor (TV). Switch your TV set’s input
to match the type of video used for the currently selected source.
Step 6. Plug all components into AC power outlets. The outlets on the back of
the AVR 435 should be used only for low-current products,such as
CD or DVD players, and the total should not exceed 100 watts.
Basic Receiver Configuration
Step 7. Select digital inputs: If your DVD is connected to Coaxial 1, no adjust-
ment is needed. For any other digital-device connections, use the
front-panel Digital Select button and the arrow buttons to select an
optical or coaxial digital input (see pages 21 and 35).
Step 8. Plug the EzSet/EQ microphone into the Microphone Jack behind the
door on the front panel. Place the microphone at your preferred listen-
ing position and then follow the instructions on pages 23 to 26 of the
Owner’s Manual and the on-screen menus to run EzSet/EQ. Note that
you will hear a series of test tones and will then be instructed to move
the microphone and point it towards the three front speakers during
the second part of the calibration process.When the on-screen
menu indicates that EzSet/EQ is complete,your system settings for
speakers, delay times, channel output and room equalization are
entered into the unit’s memory. Unplug the microphone and keep
it for future use.
Step 9.
Your system is configured – sit back and enjoy.
Figure 4 – Audio Connections
Dashed lines (––––) indicate coaxial and optical
digital audio connections. Choose either type
(but not both) for each digital audio source.
Figure 5 – Connecting EzSet/EQ Microphone

DVD PLAYER
VCR (Video 1)
In/Rec

Out/Play
LR VIDEO
Component Video
Y
Pb

Pr
Optical Coax
L R Video S-Video
Cable Box or Satellite Receiver (Video 3)
OUT
LR Video S-Video
Optical Coax
Component Video
Y
Pb
Pr
TV or Video Display
IN
Video S-Video Component Video
YPb Pr
VIDEO CONNECTIONS
Device Connection Options:Recommended connections are shown in red, but connections may be made to best fit your system requirements. The Video 4, Coaxial 4 and Optical 4 inputs are on the front panel of the receiver.
Device Input Name Audio Input Connections Audio Output Connections Video Connections
CD Player CD CD L/R Inputs, Optical Digital 1, 2 or 3, or Coaxial Digital 1, 2 or 3 Not required Not required
DVD Player DVD Coaxial Digital 1, 2 or 3, Optical Digital 1, 2 or 3, or DVD L/R Inputs Not required DVD Component Video Input, DVD Composite or S-Video
VCR Video 1 Video 1 L/R Inputs Video 1 L/R Outputs Video 1 Composite or S-Video Input and Output
Cable Box or Satellite Receiver Video 3 Video 3 L/R Inputs, Optical Digital 1, 2 or 3*, or Coaxial Digital 1, 2 or 3*Inputs Not required Component V2, Video 3 Composite or S-Video
Audio Recorder Tape Tape L/R Inputs, Optical Digital 1, 2 or 3, or Coaxial Digital 1, 2 or 3 Inputs Tape L/R Outputs, Digital Optical** or Coaxial Outputs** Not required
TV or Video Display Not applicable Not required Not required Monitor-Out Component, Composite and/or S-Video.
*Check with your cable company to determine whether digital audio is available for all channels.It may be necessary to make BOTH analog and digital connections if it is not. **Digital audio recorders only.
250 Crossways Park Drive, Woodbury,New York 11797 www.harmankardon.com © 2004 Harman International Industries, Incorporated Part No.ZKC1116HA00-8C
Power for the Digital Revolution .
®
®
Figure 6 – Video Connections
Dashed lines (––––) indicate coaxial and optical digital audio connections. Choose either type (but not both) for each
digital audio source.
Dotted lines (••••) indicate component, composite or S-video connections. Component video is the preferred connection
when available, but you may use any of the three types (but not more than one). When component, composite and
S-video sources are connected to the AVR you must also connect all outputs from the AVR to your TV.