Harman Stove Company Conquest Gas Stove User manual

1
A
B
C
R1
SAFETY NOTICE
PLEASE READ THIS ENTIRE MANUALBEFORE YOUINSTALLAND USE YOURNEW ROOMHEATER. FAILURE TO
FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTYDAMAGE, BODILYINJURY, OREVEN DEATH.
FOR USE INTHE U.S.AND CANADA. SUITABLE FOR INSTALLATIONINMOBILE HOMES
IF THIS HARMAN STOVE IS NOT PROPERLYINSTALLED,AHOUSEFIREMAYRESULT. FORYOURSAFETY,FOLLOW
INSTALLATIONDIRECTIONS.
CONTACT LOCAL BUILDING OR FIREOFFICIALSABOUT RESTRICTIONSAND INSTALLATION INSPECTION
REQUIREMENTS INYOUR AREA.
CONTACT YOUR LOCAL AUTHORITY (SUCHAS MUNICIPAL BUILDING DEPARTMENT, FIRE DEPARTMENT, FIRE
PREVENTIONBUREAU,ETC.) TODETERMINE THENEED FORAPERMIT.
CETTEGUIDE D'UTILISATIONEST DISPONIBLEENFRANCAIS.CHEZVOTRECONCESSIONNAIRE DEHARMANSTOVE
COMPANY.
SAVETHESEINSTRUCTIONS.
The Harman Conquest Gas Stove
Installation & Operating Manual
R6
“Ce manuel est disponible en Français sur demande”
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

2
CAUTION: Do notoperate the appliancewith glass removed,cracked orbroken. Replacementof the
panel(s)should bedone bya licensed orqualifiedserviceperson.
This appliancemustbeinstalled inaccordancewithlocalcodes,ifany,ifnot;followthecurrent editionofthe
National Fuel Gas Code, ANSI Z223.1 or Canadian Installation Codes, CAN/CGA B149. (Installer l’appareil
selon les codes ou règlements locaux, ou, en l’absence de tels règlements, selon les Codes d’installation CAN/
CGA-B149)
WARNING: If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
FORYOUR SAFETY
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
FORYOUR SAFETY: WHATTO DO IFYOU SMELLGAS
• Do not try to light any appliance.
• Open windows.
• Extinguish any open flame.
• Do not touch any electrical switch; do not use any phone in your building.
•Im mediately call you r gas supplier fro m a neighbor's phone.
Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified gas installer, service agency,
or the gas supplier.
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

3
Table of Contents
Introduction 4
Safety Precautions 4
Operation 5
Specifications 7
Clearances 8
Installation 9
Venting 10
Changing To Natural Gas 14
Option Installation
Thermostat 18
Remote Control 18
Glass Grill 18
Blower 19
Maintainence 20
Wiring Diagram 22
Parts 24
Trouble Shooting 26
Manufactured by The
Harman Stove Company
352 MountainHouse Rd.
HalifaxPA 17032
USA
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

4
Introduction
TheHarmanConquestDirectVent Gas Stoveisa
listed gas-fired direct vent room fireplace tested by
Intertek Testing Services/Warnock Hersey toANSI
Z21.88-2002, CSA 2.33-M02 and CANL/CGA-
2.17-M91.
The installation of the Conquest Direct Vent
Gas Stove must conform with local codes, or in the
absenceoflocalcodes, withNationalFuelGas Code,
ANSI Z223.1 — latest edition and CAN 1 B1-149.1
and .2 Installation Code.
Also for use in mobile (manufactured) homes
after home is sited.
Mobile(manufactured)homeinstallationsmust
adhere to Title 24 CFR, Part 3280, or CSA Z240.4.
CAUTION: This appliance must be vented to
the outside.
Installation and repair of the Conquest Direct
Vent Gas Stove should be done by a qualified ser-
vice person. The appliance should be inspected be-
fore use and at least annually by a qualified service
person. Morefrequent cleaningmay berequired due
to excessive lint from carpeting, bedding material,
etc. Itis imperativethat controlcompartments, burn-
ers, and circulating air passagewaysofthe Conquest
be kept clean.
When operating your Harman Conquest Gas
Stove, respect basic safety standards. Read these in-
structions carefully before you attempt to operate
the stove. Failure to do so may result in damage to
property or personal injury and may void the prod-
uct warranty.
Consult with your local building code agency
and insurance representative before you begin your
installation to ensure compliance with local codes,
including theneed forpermits and follow-up inspec-
tions.
Several issues must be addressed when select-
ing a suitable location for your Conquest Gas Stove.
Observing required clearances to combustible ma-
terials, the proximity to a safe chimney or venting
system location, and the accessibility of the gas and
electricalsupply must all be considered. In addition,
selecting a location that takes advantage of the
building's natural air flow is also desirable to maxi-
mize the heatingeffectiveness of the stove. In many
cases, this is a central location within the building.
Duetohightemperatures,theConquestDirect
Vent Gas Stove should be located outof traffic
and away from furniture and draperies.
Children and adults should be alerted to the
hazards of high surface temperatures and
should stay away to avoid burns or clothing
ignition.
Youngchildrenshould becarefullysupervised
when they are in the same room as the
appliance.
Clothing or otherflammable materials should
not be placed on or near the appliance.
Surveiller les enfants. Garder les vetements,
les meubles, lessence ou autres liquides a
vapeur inflammables lin de lappareil.
This appliance may be installed in an after-
market permanently located (mobile) home,
where not prohibited by local codes.
This appliance is only for use with the
type(s) of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified kit is used.
Cet appareil peut etre installe dans un
maison prefabriquee (mobile) deja installee a
demeure si les reglements locaux le permettent.
Cet appareil doit etre utilise uniquement
avec les types de gas indiques sur la plaque
signaletique. Ne pas l utiliser avec d autres gas
sauf si un kitde conversion dertifie est installe.
Anysafetyscreenor guard removedfor servicing
anappliance mustbe replaced prior tooperating
the appliance.
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

5OPERATION
Operation
HOW TO LIGHT THE FIRE
1. STOP! Read the safety information on the
front cover of this manual.
2. If using the optional thermostat, set thermostat
to the lowest setting.
3. Turn off electric power to the optional blower.
4. Turn the ON-OFF switch to the OFF position.
5. Push in the gas control knob slightly and turn it
clockwise to "OFF." NOTE: THE KNOB
CANNOT BE TURNED FROM "PILOT" TO
"OFF" UNLESS IT IS PUSHED IN SLIGHTLY.
DO NOT FORCE IT.
6. Wait five (5) minutes to clear out any gas. If
you then smell gas, STOP! Follow "B" in the
safety information on the front cover. If you
don't smell gas, go to the next step.
7. Set the High-Low Regulator to High by turning
it fully counterclockwise.
8. Press in the gas control knob slightly and turn
counterclockwise to "PILOT."
9. Find the pilot by looking down between the
logs as shown at lower left.
10. Push the control knob fully down and hold.
Immediately push the red piezo ignitor button to
light the pilot. It is normal to have to push the
red button several times before the pilot ignites.
Continue to hold the control knob in for about
one (1) minute after the pilot is lit. Release the
knob and it will pop back up. Pilot should
remain lit. If it goes out, repeat steps 5
through 10.
•If the knob does not pop up when re-
leased, stop and immediately call your service
technician or gas supplier.
•If the pilot will not stay lit after several
tries, turn the gas control knob to "OFF" and
call your service technician or gas supplier.
11. Turn the gas control knob counterclockwise to
"ON."
12. Place the ON-OFF switch in the ON position
or turn up the thermostat setting if the optional
thermostat is used.
13. Turn on the electric power to the optional
blower if installed.
14. Set the optional thermostat to the desired
room temperature.
Piezo Ignitor
Button
PILOT
Gas Control
High-Low
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

6OPERATION
15. Set the High-Low Regulator to desired setting:
Turn fully counterclockwise for High and fully
clockwise for Low.
NOTE: An odor, resulting from the initial heating
of new materials in your heater, is not unusual
during the first fire, and in most cases will
disappear after an hour or two.
HOW TO TURN OFF THE FIRE
1. If using optional thermostat, set thermostat to
the lowest position.
2. Turn off the electric power to the blower.
3. Turn the ON-OFF switch on the upper right
rear of the stove to the OFF position.
4. Push in the gas control knob slightly and turn it
clockwise to “OFF.”
NOTE: The knob cannot be turned from “PILOT”
to “OFF” unless it is pushed in slightly. Do not
force it.
FLAME HEIGHT ADJUSTMENT
The flame height adjuster can be accessed by
openingthe right side panel.Turn theadjuster clock-
wise to increase flame height and counterclockwise
to decrease. See above left. Adjusting the flames
toohigh willcause them to haveblack tipsand cause
sooting. Sooting can cause the glass to get dirty.
Check flame height after five to ten minutes and re-
adjust if necessary.
PilotFlames
If pilot flames are less than shown at left, use
pilot adjuster shown below, to increase flames.
FlameHeight
Adjuster
Normal Flame pattern. Note: Flames will vary in height and
position depending on theplacement and the amount of
ember wool.
Warning: The unit and
adjuster may be hot.
Wear gloves and arm
protection if making
adjustments while in
operation.
Pilot Adjuster
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

7SPECIFICATIONS
RATINGS NATURAL PROPANE
Input Rating(Btu/hr)(0-4500 ft.)(0-1375 m) 29000 29000
Min. Input Rating(Btu/hr)(0-4500 ft.)(0-1375 m) 14900 14100
Orifices (DMS)(0-4500 ft.)(0-1375 m) 37 53
ManifoldPressure (inw.c./kPa) 3.8/.95 11.0/2.75
Min. Manifold Pressure (in w.c./kPa) 1.1/.27 2.8/.7
Min. Inlet Pressure (in w.c./kPa) 5.0/1.25 11.5/2.87
Max. Output (Btu/hr)(0-4500 ft.)(0-1375 m) (Blower Off) 21375 21854
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

8SPECIFICATIONS
MINIMUM CLEARANCES FROM COMBUSTIBLE CONSTRUCTION
Unit to corner walls 2 in.
Unit to side wall 8 in.
Unit to back wall 3 in.
Unit to alcove ceiling 16 in.
Maximum alcove depth 16 in.
Electrical Rating: 120 Volts, 60 Hz, > .7 AMP
8”
3”
2”
2”
16”
8”8”
16”
Alcove Clearances
Side And Back Wall Clearances Corner Clearances
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

9INSTALLATION
Only For Qualified Installers
Burn Only the Fuel for which the Heater is
Equipped
TheConquest can burn eithernaturalgasor pro-
pane, but requires a change-over kit for natural gas.
The labelon theburner system module indicates the
fuelfor which it is equipped.Asecond label, (on the
valve) also indicates the fuel type.
Making The Connection
The gas inlet is located on the bottom right side
of the stove. The inlet fitting is a 1/2" male flare
fitting.
A separate gas shut-off valve and a 1/8" N.P.T.
pluggedtapping should be installedimmediately up-
stream of the connection to the appliance.
The Conquest Direct Vent Gas Heater must be
disconnected from the gas supply piping during any
pressuretestingofthat system at pressuresin excess
of 1/2 psig (3.5 kPa).
The Conquest gas control valve must be in the
OFF position during any pressure testing of the gas
supply system at pressures equal to or less than 1/2
psig (3.5 kPa).
WARNING: To avoid pipe compounds from
enteringintothe gas train, applycompounds only
tomale pipe threads and do notapply compound
to the first two threads.
CAUTION: TESTALL JOINTS FOR LEAKS
BEFORE OPERATING.
Gas Pressure Requirements:
Correct gas pressure and the use of a properly
sized gas supply line are essential for the safe and
efficient performance of this appliance. Make sure
that the plumber or gas supplierchecks the gas sup-
ply line and gas pressure at installation.
NOTE:Improper gaspressure can affect heater
performance, flame color, or cause pilot outage.
Natural Gas:
Maximum inlet pressure 7.0" w.c. (1.74 kPa)
Minimum inlet pressure 5.0" w.c. (1.25 kPa)
Gas manifold pressure 3.8" w.c. (0.87 kPa)
LPG Gas:
Maximum inlet pressure 13" w.c. (3.24 kPa)
Minimum inlet pressure 11.5" w.c. (2.74 kPa)
Gas manifold pressure 11" w.c. (2.49 kPa)
DO NOT USE THIS HEATER IF ANY PART
HAS BEEN UNDER WATER OR EXPOSED TO
MOISTURE CORROSION. IMMEDIATELY
CALLAQUALlFlED SERVICETECHNICIAN TO
INSPECT THE HEATER AND REPLACE ANY
PART OF THE CONTROL SYSTEM AND ANY
GAS CONTROL WHICH HAS BEEN UNDER
WATER.
PipeLength Schedule40Pipe Tubing,TypeL
(Feet) InsideDiameter OutsideDiameter
N.G. L.P. N.G. L.P.
0-10 1/2" 3/8" 1/2" 3/8"
1.3cm 1.0cm 1.3cm 1.0cm
10-40 1/2" 1/2" 5/8" 1/2"
1.3cm 1.3cm 1.6cm 1.3cm
40-100 1/2" 1/2" 3/4" 1/2"
1.3cm 1.3cm 1.6cm 1.3cm
100-150 3/4" 1/2" 7/8" 3/4"
2.0cm 1.3cm 2.3cm 2.0cm
RECOMMENDED GAS PIPE DIAMETER
NOTE: NEVER USE PLASTIC PIPE. CHECK TO
CONFIRM WHETHER YOUR LOCAL CODES ALLOW
COPPER TUBING OR GALVANIZED PIPE.
A LABEL ON THE BURNER SYSTEM
MODULE STATES THE FUEL FOR
WHICH THE HEATER IS EQUIPPED.
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

10INSTALLATION
Only For Qualified Installers
6-5/8 x 4 8” x 5” Description
n/a 1208 6” Pipe Length
908B 1208B 6” Pipe Length, Black
n/a 1207 9” Pipe Length
907B 1207B 9” Pipe Length, Black
906 1206 12” Pipe Length
906B 1206B 12” Pipe Length, Black
904 1204 24” Pipe Length
904B 1204B 24” Pipe Length, Black
903 1203 36” Pipe Length
903B 1203B 36” Pipe Length, Black
902 1202 48” Pipe Length
902B 1202B 48” Pipe Length, Black
n/a 1211 11” to 14-5/8” Pipe, Adjustable
911B 1211B 11” to 14-5/8” Pipe, Adjustable, Black
n/a 1217 17” to 24” Pipe, Adjustable
945 1245 45oElbow
945B 1245B 45oElbow, Black
990 1290 90oElbow
990B 1290B 90oElbow, Black
940 1240 Rnd Support Box/Wall Thimble Cover
941 1241 Cathedral Ceiling Support Box
943 1243 Flashing, 0/12 to 6/12 Roof Pitch
943S 1243S Flashing, 7/12 to 12/12 Roof Pitch
953 1253 Storm Collar
963 1263 Ceiling Firestop
988 1288 Wall Strap
981 1281 Snorkel Termination (36”)
982 1282 Snorkel Termination (14”)
984 1284 Horizontal Square Termination
980 1280 Vertical Termination
991 1291 Vertical Termination, High Wind
950 1250 Vinyl Siding Standoff
1222D (Only available from Harman) 8” x 5” to 6 5/8” x 4” Adaptor
Part Numbers for SimpsonDura-Vent Pipe and Fittings
Use Only Approved Venting
This appliance has been tested and is listed for installation with Simpson Duravent GS venting com-
ponents. The Simpson Duravent GS warranty will be voided, and serious fire, health, or other safety
hazards may result from any of the following actions:
• Installation of any damaged Duravent GS component.
• Unauthorized modification of the Duravent GS System.
• Installation of any component part not manufactured or approved by Simpson Duravent.
• Installation other than as instructed by Simpson Duravent and the appliance manufacturer.
Consult your local building codes before beginning the installation, and follow the manufacturer's
instructions exactly. The Simpson Duravent GS venting components listed below are approved for use
with the Conquest Direct Vent Gas Stove.
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

11INSTALLATION
Only For Qualified Installers
Maximum of four 450elbows allowed.
Subtract threefeet of total horizontal pipe
length for each of the 3rd and 4th 450elbows
used.
Maximum of two 900elbows allowed.
Subtract five feet of total horizontal pipe
length for second elbow.
Venting with 6 5/8” x 4” Pipe
Acombination of one 900elbow and two 450
elbows is allowed.
Subtract threefeet of total horizontal pipe
length for each 450 elbow used.
This appliance must not be
connected to a chimney flue
serving a separate solid fuel
burning appliance.
6 5/8” to 8” Increaser
8”
CONQUEST
Rear Vent
A snorkel termination is
recommended when no
vertical pipe is used.
Vent termination mustremain within the
shaded area regardless of configuration.
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

12INSTALLATION
Only For Qualified Installers
Requirements for Terminating the Venting
WARNING: Venting terminals must not be re-
cessed into a wall or siding.
In addition, the following must be observed:
A. The clearance above grade, or a veranda,
porch, deck or balcony must be a minimum of 12"
(30 cm).1
B. The clearance to a window or door that may
be opened must be a minimum of 12" (30 cm).1
C. A 12" (30 cm) clearance to a permanently
closed window is recommended to prevent con-
densation on the window.
D. The vertical clearance to a ventilated soffit
located above the terminal within a horizontal dis-
tance of 2 feet (60 cm) from the center-line of the
terminal must be a minimum of 18" (46 cm).
E.The clearance to an unventilated soffit must
be a minimum of 12" (30 cm).
F. The clearance toan outsidecorner is11"from
center of pipe.
G. The clearance to an inside corner is 12" (30
cm). H. A vent must not be installed within 3 feet
(90 cm) above a meter/regulator assembly when
measured from the horizontalcenter-line oftheregu-
lator.1
I. The clearance to service regulator vent outlet
must be a minimum of 6 feet (1.8 m).1
J. The clearance to a non-mechanical air sup-
ply inlet to the building or the combustion air inlet
to any other appliance must be a minimum of 12
inches (30 cm).1
K. The clearance to a mechanical air supply
inlet must be a minimum of 6 feet (1.8 m).1
L. The clearance above a paved sidewalk or a
paved driveway located on public property must be
a minimum of 7 feet (2.1 m).1,2
M. The clearance under a veranda, porch, deck
or balcony must be a minimum of 12 inches (30
cm).1,3
1As specified in CAN 1 B1-149 Installation
Codes (currentedition). Note: Localcodesorregula-
tionsmayrequiredifferentclearances.
2Avent shallnot terminatedirectly abovea side-
walk or paved driveway which is located between
two single family dwellings and serves both dwell-
ings.3Only permitted if veranda,porch, deck, or bal-
cony is fully open on a minimum of 2 sides beneath
the floor.
VA
=Ventterminal =Airsupply inlet
Fixed
Closed
Openable
Openable Fixed
Closed
InsideCorner
Detail
=Areawhereterminalisnotpermitted
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

13INSTALLATION
Only For Qualified Installers
Natural Gas or Propane
0 Feet (rear Vent) Open
6 feet 1/4 to Open
12 feet 1/4 to Open
24 feet Closed to 1/2
36 feet Closed to 1/2
Range OfApproved Damper Settings
A vent damper is provided to allow fine tuning
of the draft. Too little draft will cause flames to be
too long with black tips and too much draft will
cause flames to be short and blue.
To adjust the damper, burn the unit on High 10
minutes or more. Adjust the vent damper to a posi-
tion in therangeslisted belowthat producesthemost
desirable flame pattern. Note: 1 is less draft and 4 is
maximum draft.
Damper Settings
Top Vent Only
Vent damper shown in the
Maximum Draft”OPEN” position
for top vent.Note: This would be
the Minimum Draft”CLOSED”
position if a rear vent was
installed.
OPEN
CLOSED
ONE HALF
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

14INSTALLATION
Only For Qualified Installers
Changing to Natural Gas
Remove pilot tower with
a 7/16” wrench. Replace
LP orifice with Natural
Gas orifice. See
instructionsin kit.
Use a 1/2” deep well
socket to remove the LP
#53 orifice and replace
with the #37 Natural gas
orifice from the kit.
Natural Gas Kit PartNo.1-00-09112
NG Conversion label
NG Orifice #37
NG Valve
Conversion
Module
NG Conversion
Instructions
This kit is only for use in the Conquest direct
vent gas stove.
Natural Gas Conversion Kit
NG Pilot Orifice
Remove the three screws that hold the
LP knob module in place. Remove the
module and replace with the Natural
gas module from the kit. See kit
instructions.
Remove four
boltsand
remove burner
modulefrom
stove.
3
1
2
4
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

15INSTALLATION
Only For Qualified Installers
Place conversion sticker (provided in Kit) on the valve. This
is to permanently mark the valve that it has been converted
to Natural Gas. This label isimportant in the event that the
valve is ever removed and mixed in with other valves.
6
Mark the proper box on the
label with a permanent marker.
Note: If no conversion is made,
the box for the propane box must
still be marked by the installer.
7
Note: The higher the orifice number the smaller
hole in the tip. For example, a number 52
orifice has a larger hole than a number 60
orifice.
5
Reinstall burner module back into the
stove with the four bolts that were
removed. Check gasket for damage
and replace if necessary. Check for
gas leaks when finished.
9
Verify gas inlet and manifold pressures are within the
specifications on the appliance data plate located inside the
bottom of the unit.
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

16INSTALLATION
Only For Qualified Installers
Rear Log
Front Log
Place the rear log behind the front log with the branch
resting on the front log on the right side as shown.
Place thefront log as shown between the andironsand the
air deflector.
Log Placement
Andirons
Air Deflector
Before lighting a fire check that the rear
log is as far back against the rear wall as
possible.
The front log should be slide rearward in
it’s position between the andirons and
deflector plate.
Ember Placement
After the logs are positioned, place the embers
as shown above.
There are two typesof embers supplied.One is
a wool like material and the other like a nugget.
The wool is to be placed on the screen by pull-
ing smallpieces from the bunch with yourfingers or
a tweezers. Place the wool lightly on the screen over
the horse shoe tube area. Be careful not to compact
thewool.The looserand fluffierthe better.The place-
ment and density of the wool changes the front
flames and glowing embers. You can try different
placement to get the look you prefer.
Placenuggets where desired elsewherein front
of the log.
Wool Nuggets
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

17INSTALLATION
Only For Qualified Installers
Tile Kit
Each tile kit contains six tiles and fifteen allen-
set screws. Ifthe Conquest is installed as a top vent,
then the round tile is not used. If it is installed as a
rear vent, then the trim ring is not used.
Installing Tiles
Below each tile opening are three threaded
holes. In some cases it may be helpful to remove
extra paint from the treads with a 1/4-20 tap.
1. Screw the set screws down until the top of the
screw is about the thickness of the tile below the
top surface.
2. Place the proper tile in the opening.
3. Observe the level of the tile. If the level of the
tile is not satisfactory, remove the tile by press-
ing down on one of the corners and adjust set
screws accordingly.
Round Tile Not
Used On Top Vent
Trim Ring Not
Used On Rear
Vent.
Allen Set
Screws
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

18INSTALLATION (Options)
Only For Qualified Installers
Connecting the Optional Thermostat
If the optional thermostat is used, it must be
plugged into the TH terminals located on the
valve.
When installing a millivolt controlsystem, use
only a special low resistance thermostat. DO NOT
USE A REGULAR HEATING THERMOSTAT.
Be surethat allelectricalconnectionsare clean,
free from corrosion, and tight. Inspect connections
periodically to confirm that no corrosion has built
up over time.
When properly installedand maintained,a mil-
livolt control system should give many years of
trouble-free service.
It is important to use wire of a gauge proper
for the length of the wire:
RECOMMENDED WIRE GAUGES
Maximum Wire
Length Gauge
100' 14
60' 16
40' 18
25' 20
15' 22
Thermostat
Remote Control Kit
The button on the remote control can be used
to turn the fire on and off.
This remote uses the ultrasonic controlmethod
and does not need to be pointed directly at the fire-
place.
Thekit includesinstallation instructions,a hand
held sending unit, receiving unit, mounting bracket,
and all wiring.
Note: The ON/OFF switch must be “OFF”
when using the remote. If the switch is in the “ON”
position, the fire willstay on even when the set tem-
perature on the thermostat is reached.
Glass Grill
To install the glass grill remove the door and
slide the top of the vertical bars up into the slots at
the top of the firebox opening. Lower the grill down
so the bottom of the vertical bars rest just inside the
lip at the bottom of the firebox opening.
Reinstall door.
BurnerButton
Glass Grill
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

19INSTALLATION (Options)
Only For Qualified Installers
Optional Blower
The Blower Kit (Part # 1-00-09102) includes a
blower assembly ready to bolt to the left side of the
stove and a blower chamber cover.
The blower has a variable speed control knob
to adjusttheblowerspeedasdesired.Aspecialswitch
is used to automatically start the blower when the
stove temperature is hot enough to blow warm air.
This switch will also stop the blower when the stove
temperature drops below the point that warm air is
available.
Installation
1. Open the left side panel.
2. Remove the four screws from the left side of the
firebox with a 5/16” socket.
3. Place the blower as shown and start the top
screw. This will hold the blower in place and
make it easier to install the other three screws.
4. Route the power cord rearward between the side
panel and the pedestal and plug into a 120 volt
outlet.
5. Open the right side panel and remove the two
screws on the right side of the firebox.
6. Use the two screws to fasten the blower cham-
ber cover plate to the firebox. This plate pre-
vents air from the blower escaping from the air
chamber.
7. Close side panels.
Operation
Turn the speed control knob clockwise until it
clicks. This is the full speed position. Turning the
knob farther in the clockwise direction will gradu-
ally reduce the blower speed. To turn the blower
“OFF” turn the knob counterclockwise until it clicks.
Blower Assembly
Speed Control Knob
Blower Chamber Cover
Power Cord
This blower is equipped with a three-prong
(grounding) plugfor protectionagainst shock
hazard and should be plugged directly into a
properly grounded three-prong receptacle.
Do not cut or remove the grounding prong
from the plug.
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

20MAINTENANCE
Removing the Glass Front
Remove the air grill by pulling forward.
Lift thelatch shownabove andtilttheglass door
out at the top and lift off the hooks at the bottom.
Handle the glass with care.
Replacing the Gasket
The Conquest uses part no. 3-44-00539 fiber-
glass gasket in the front door. Should it ever need
replacement, use only the proper replacement gas-
ket that is available from your Harman dealer. Re-
place the gasket as follows:
1. Lay glass door face down on a soft surface that
will not scratch the glass.
2. Remove the nuts holding the top and bottom
glass clip in place.
3. Remove glass from door and remove old gasket.
4. Install new gasket around glass.
5. Place glass back in door.
6. Reinstall glass clips and tighten the nuts.
7. Reinstall glass door by placing the slots on the
bottom of the door overthe hooks on the bot-
tom of the door opening. Next, lift the latch and
push the door against the unit. Pull the spring
loaded latch front until the tab drops into the
slot on the door frame.
8. Reinstall air grill.
Cleaning the Glass
The glass may be cleaned with ordinary house-
hold glass cleaner and a soft cloth or paper towel.
WARNING:Never clean the glass when it is
hot. Do not use abrasive cleaners on the glass.
A qualifiedservicepersonshould conduct
an annualinspection and maintenance of your
Conquest, its venting, and the installation to
keep it running safely and efficiently. The fol-
lowing procedures should be performed only
by a qualified service person. The gas supply
should be turned off whenever a maintenance
procedure is performed.
Iftheglass doororsidedoorsare removed
for servicing, they must be replaced prior to
operating the stove.
CAUTION: Do not operate this appliance
with the glass front removed, cracked, or
broken.Replacementof glass shouldbe done
by a licensed or qualified service person.
Never use substitute materials.
CAUTIONNER: N’opère l’appareil avec le
verre enlève, craque ou casse. Le
remplacement dupanneau(s) devraitêtre fait
par une personne de service qualifiá ou
autorisá.
DO NOT STRIKE OR SLAM GLASS
Latch
Air Grill
Gold Frame Door
Glass
Gasket
Top
Clip
Bottom
Clip
Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.