Harman HS 300 User manual

HS 300/500 Home Cinema System
SERVICE MANUAL
27820_HS500_Eng 07/08/06 14:22 Side 1
CONTENTS
SERVICE INFO, MECHAS 2 UNIT EXPLODED VIEW AND PARTS 11
SERVICING PRECAUTIONS 3 PARTS LIST 12
ESD PRECAUTIONS 5 PINOUTS 69
BASIC SPECIFICATIONS 300 6 PCB DRAWINGS 85
BASIC SPECIFICATIONS 500 7 BLOCK DIAGRAM 93
TROUBLESHOOTING GUIDE 8 WIRING DIAGRAM 94
PACKING LIST AND VIEW 10 SCHEMATIC DIAGRAMS 95
harman/kardon
service manual
Page 1 of 109

harman/kardon Service Info
HS 300/500 23 Aug 2007
To: All harman/kardon Service Centers
Models: HS 300/500
Subject: Hardware changes (2 changes, mecha and main board).
Please note that a change in hardware from Sanyo optics and mecha to Hitachi optics and
mecha has been carried out from the serial numbers stated below.
Model Start serial number End serial number Optic / mecha Part number
WA0020-01001 WA0020-03501 HD62 - DV342 (Sanyo) 01.15.JX.DV342
HS 300/230 WA0020-03502 - HOP1200W- DM3403-C
(Hitachi) 01.15.JX.EDM3403
WA0023-01001 WA0023-03500 HD62 - DV342 (Sanyo) 01.15.JX.DV342
HS 500/230 WA0023-03501 - HOP1200W- DM3403-C
(Hitachi) 01.15.JX.EDM3403
Due to the change of mecha, the main boards are also different. It is important to use the correct
main board for the loader, as the servo circuit has changed on the main board.
Model Start serial number End serial number Main board version Part number
WA0020-01001 WA0020-03501 Up to version 1.6 HAV06M1802C02*
HS 300/230 WA0020-03502 - From version 1.7 0211HAV06M3625C023
WA0023-01001 WA0023-03500 Up to version 1.6 HAV06M1802C02*
HS 500/230 WA0023-03501 - From version 1.7 0211HAV06M3625C025
* Please note that correct software according to model must be installed after change of main
board
harman/kardon
service manual
Page 2 of 109

1
SERVICING PRECAUTIONS
NOTES REGARDING HANDLING OF THE PICK-UP
1. Notes for transport and storage
1) The pick-up should always be left in its conductive bag until immediately prior to use.
2) The pick-up should never be subjected to external pressure or impact.
2. Repair notes
1) The pick-up incorporates a strong magnet, and so should never be brought close to magnetic materials.
2) The pick-up should always be handled correctly and carefully, taking care to avoid external pressure and
impact. If it is subjected to strong pressure or impact, the result may be an operational malfunction
and/or damage to the printed-circuit board.
3) Each and every pick-up is already individually adjusted to a high degree of precision, and for that reason
the adjustment point and installation
screws should absolutely never be touched.
4) Laser beams may damage the eyes!
Absolutely never permit laser beams to enter the eyes!
Also NEVER switch ON the power to the laser output part (lens, etc.) of the pick-up if it is damaged.
5) Cleaning the lens surface
If there is dust on the lens surface, the dust should be cleaned away by using an air bush (such as used
for camera lens). The lens is held by a delicate spring. When cleaning the lens surface, therefore, a cot-
ton swab should be used, taking care not to distort this.
6) Never attempt to disassemble the pick-up.
Spring by excess pressure. If the lens is extremely dirty, apply isopropyl alcohol to the cotton swab. (Do
not use any other liquid cleaners, because they will damage the lens.) Take care not to use too much of
this alcohol on the swab, and do not allow the alcohol to get inside the pick-up.
Storage in conductive bag
NEVER look directly at the laser beam, and don’t let contact
fingers or other exposed skin.
Magnet
How to hold the pick-up
Conductive Sheet
Cotton swab
Pressure
Pressure
Drop impact
harman/kardon
service manual
Page 3 of 109

2
NOTES REGARDING COMPACT DISC PLAYER REPAIRS
1. Preparations
1) Compact disc players incorporate a great many ICs as well as the pick-up (laser diode). These compo-
nents are sensitive to, and easily affected by, static electricity. If such static electricity is high voltage,
components can be damaged, and for that reason components should be handled with care.
2) The pick-up is composed of many optical components and other high-precision components. Care must
be taken, therefore, to avoid repair or storage where the temperature of humidity is high, where strong
magnetism is present, or where there is excessive dust.
2. Notes for repair
1) Before replacing a component part, first disconnect the power supply lead wire from the unit
2) All equipment, measuring instruments and tools must be grounded.
3) The workbench should be covered with a conductive sheet and grounded.
When removing the laser pick-up from its conductive bag, do not place the pick-up on the bag. (This is
because there is the possibility of damage by static electricity.)
4) To prevent AC leakage, the metal part of the soldering iron should be grounded.
5) Workers should be grounded by an armband (1MΩ)
6) Care should be taken not to permit the laser pick-up to come in contact with clothing, in order to prevent
static electricity changes in the clothing to escape from the armband.
7) The laser beam from the pick-up should NEVER be directly facing the eyes or bare skin.
Resistor
(1 Mohm) Conductive
Sheet
Resistor
(1 Mohm)
Armband
harman/kardon
service manual
Page 4 of 109

3
ESD PRECAUTIONS
Electrostatically Sensitive Devices (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components com-
monly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated cir-
cuits and some field-effect transistors and semiconductor chip components. The following techniques should
be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off
any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a
commercially available discharging wrist strap device, which should be removed for potential shock reasons
prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive sur-
face such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static"
can generate electrical charges sufficient to damage ESD devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD
devices.
6. Do not remove a replacement ESD device from its protective package until immediately before you are
ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive materials).
7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the
protective material to the chassis or circuit assembly into which the device will by installed.
CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL
OTHER SAFETY PRECAUTIONS.
8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion
such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can gen-
erate static electricity sufficient to damage an ESD device).
harman/kardon
service manual
Page 5 of 109

HS 300 CONTROLLER SPECIFICATIONS 31
ENGLISH
HS 300 Controller Specifications
DVD player Pickup: Semiconductor laser, wavelength 650nm
Signal system: NTSC / PAL
Video signal horizontal resolution: More than 480 lines (DVD)
Video signal-to-noise ratio: More than 60 dB (DVD)
Audio frequency response: DVD (PCM):20Hz ~ 22kHz (+/- 1.0dB)
(Stereo) CD (PCM):20Hz ~ 20kHz (+/- 1.0dB)
Audio signal-to-noise ratio: More than 80 dB (PCM)
Total harmonic distortion:: Less than 0.01% (PCM)
Dynamic range: DVD (PCM):More than 85 dB (EIAJ, 2kHz)
CD:More than 85 dB (EIAJ)
FM Tuner System: PLL quartz-locked digital synthesizer system
Tuning range: 87.50 ~ 108.00 MHz
Antenna terminals: 75 Ohms, unbalanced
Intermediate frequency: 10.7 MHz
Video Outputs HDMI:
ComponentVideo Output: Y: 1Vp-p/75 Ohms, sync negative polarity
Cr:0.7Vp-p/75 Ohms
Cb:0.7Vp-p/75 Ohms
CVBSVideo: 1Vp-p 75 Ohms
S-video: Y: 1Vp-p 75 Ohms
C:PAL 0.3Vp-p 75 Ohms / NTSC 0.286 Vp-p 75 Ohms
Audio line Outputs
Audio L/R: 2Vrms,1 kilohms
General Power requirements: AC 230V, 50 Hz
Max power consumption: 400W
Idle power consumption: Less than 2W
Dimensions (WxHxD): 440mm x 68mm x 380mm
Weight: 7.5 kg
* Designs and specifications are subject to change without notice.
Depth measurement includes knobs,buttons and terminal connections.Height measurement includes feet and chassis.
All features and specifications are subject to change without notice.
Harman Kardon is a registered trademark of Harman International Industries, Incorporated.
Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories,registered in the United States and/or other countries.All rights reserved.
DTS is a trademark of DigitalTheater Systems, Inc.
Windows Media®Audio (WMA) is a proprietary file format developed by Microsoft.
DivX is a registered trademark of DivX,Inc.
HDMI,the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
28098_HS300_Eng 07/08/06 14:21 Side 31
harman/kardon
service manual
Page 6 of 109

HS 500 CONTROLLER SPECIFICATIONS 31
ENGLISH
HS 500 Controller Specifications
DVD player Pickup: Semiconductor laser, wavelength 650nm
Signal system: NTSC / PAL
Video signal horizontal resolution: More than 480 lines (DVD)
Video signal-to-noise ratio: More than 60 dB (DVD)
Audio frequency response: DVD (PCM):20Hz ~ 22kHz (+/- 1.0dB)
(Stereo) CD (PCM):20Hz ~ 20kHz (+/- 1.0dB)
Audio signal-to-noise ratio: More than 80 dB (PCM)
Total harmonic distortion:: Less than 0.01% (PCM)
Dynamic range: DVD (PCM):More than 85 dB (EIAJ, 2kHz)
CD:More than 85 dB (EIAJ)
FM Tuner System: PLL quartz-locked digital synthesizer system
Tuning range: 87.50 ~ 108.00 MHz
Antenna terminals: 75 Ohms, unbalanced
Intermediate frequency: 10.7 MHz
Video Outputs HDMI:
ComponentVideo Output: Y:1Vp-p/75 Ohms,sync negative polarity
Cr:0.7Vp-p/75 Ohms
Cb:0.7Vp-p/75 Ohms
CVBSVideo: 1Vp-p 75 Ohms
S-video: Y: 1Vp-p 75 Ohms
C:PAL 0.3Vp-p 75 Ohms / NTSC 0.286 Vp-p 75 Ohms
Audio line Outputs
Audio L/R: 2Vrms,1 kilohms
General Power requirements: AC 230V, 50 Hz
Max power consumption: 500W
Idle power consumption: Less than 2W
Dimensions (WxHxD): 440mm x 68mm x 380mm
Weight: 8,5 kg
* Designs and specifications are subject to change without notice.
Depth measurement includes knobs,buttons and terminal connections.Height measurement includes feet and chassis.
All features and specifications are subject to change without notice.
Harman Kardon is a registered trademark of Harman International Industries, Incorporated.
Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories,registered in the United States and/or other countries.All rights reserved.
DTS is a trademark of DigitalTheater Systems, Inc.
Windows Media®Audio (WMA) is a proprietary file format developed by Microsoft.
DivX is a registered trademark of DivX,Inc.
HDMI,the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
27820_HS500_Eng 07/08/06 14:22 Side 31
harman/kardon
service manual
Page 7 of 109

28 TROUBLESHOOTING
Troubleshooting
If you experience any of the following difficulties
while using the system,use this troubleshooting
guide to help you remedy the problem.
Should any problem persist,consult your
authorized Harman Kardon dealer.
No power.
• Is the power cord firmly plugged into the
power outlet?
• One of the safety mechanisms may be operat-
ing.In this event, unplug the player from the
power outlet briefly and then plug it in again.
No picture.
• Check that the system is connected correctly
and securely.
•The video cable may be damaged.Replace it
with a new one.
• Make sure the system is connected to a video
input on theTV (see page 14).
• Make sure theTV is turned on.
• Make sure the correct video input on theTV is
selected for viewing with this system.
Noise (interference) appears in the
picture.
• Clean the disc.
• If video from this system has to go through
yourVCR to get to yourTV, the copy-protection
applied to some DVD programs could affect
picture quality. If you still experience problems
after checking your connections,please try con-
necting your DVD system directly to yourTV’s
S-Video input,if yourTV is equipped with this
input (see page 14).
The aspect ratio of the screen is wrong
(picture vertically expanded) when you
play a wide picture even though you set
“TV DISPLAY” in the SETUP menu to
"16:9".
• If you connect the system with the SCART
cable,connect directly to theTV. Otherwise the
autoswitch function of the aspect ratio for the
TV may not work.
• If theTV is not connected with a SCART cable
to the HS,or if the autoswitch function does
not work you should turn theTV to "16:9" (if
possible with yourTV).
• Depending on theTV,you may not be able to
change the aspect ratio. In that case (TV not
adjustable to 16:9) do not select "16:9" in the
TV Display.Then, no change of the aspect ratio
is needed.
There is no sound or volume is very low.
• Check that the speakers and components are
connected correctly and securely.
• Make sure that you have selected the correct
source on the system.
• Press MUTE on the remote control,if the
words MUTE ON are blinking on the front
panel display.
•The protective circuitry has been activated
because of a short circuit.Turn off the system,
eliminate the short circuit problem and turn on
the power again.
•The audio interconnect is damaged.Replace it
with a new one.
•The system is in pause mode or in slow-motion
play mode,or fast forward or fast reverse.
Press Nto return to normal play mode.
• Check the speaker settings (see page 19).
The left and right channels are unbalanced
or reversed.
• Check that the speakers and components are
connected correctly and securely.
Severe hum or noise is heard.
• Check that the speakers and components are
connected securely.
• Check that the connecting cords are away from
a transformer or motor and at least 3 meters
away from fluorescent light.
• Move yourTV away from the audio compo-
nents.
•The plugs and jacks are dirty.Wipe them with a
cloth slightly moistened with alcohol.
• Clean the disc.
The surround effect is difficult to hear
when you are playing a Dolby Digital
sound track.
• Check to see if the Dolby Digital mode is
turned on properly, otherwise unload and load
the disc again.
• Check the speaker connections.
• Depending on the DVD disc,the output signal
may at times be mono or stereo even if the
soundtrack is recorded in Dolby Digital format.
The sound comes from the center speaker
only.
• Depending on the disc,sound may sometimes
come from the center speaker only.This also
applies to mono recordings (from disc or any
analog source),when Pro Logic mode is
selected.This is normal.
No sound is heard from the center speaker.
•Adjust center speaker volume (see pages 19).
No sound or only very low volume from
the rear speakers.
•Adjust the rear speaker volume (see page 19).
The volume goes down automatically
and can not be increased.
•The internal temperature is too high.Wait
approximately one minute for the amplifier to
reach normal working temperature.
Radio stations cannot be tuned in.
• Check that the antenna is connected correctly.
Adjust the antenna and connect an external
antenna if necessary.
•The signal strength of the stations is too weak
for automatic tuning.Use manual tuning.
• No stations have been preset.
•The tuner mode is not selected,select the
Radio mode.
The remote does not function.
• Remove any obstacles between the remote
control and the system.
• Move the remote control closer to the system.
• Point the remote control at the remote sensor
on the front panel.
• Replace all the batteries in the remote control
with new ones if they are weak.
• Check that the batteries are loaded correctly.
The disc does not play.
•There is no disc inside.(“NO DISC” appears on
the front panel display and theTV screen.)
Insert a disc.
• Insert the disc correctly with the playback side
facing down on the disc tray.
• Clean the disc.
•The system cannot play CD-ROM's,etc.
(see page 3).
• DVD with wrong region code
(see page 13).
The system starts playing the DVD auto-
matically.
•The DVD features the auto playback function.
Playback stops automatically.
• Some discs include an auto pause signal.When
playing such a disc,the system stops playback
at the signal.
27820_HS500_Eng 07/08/06 14:22 Side 28
harman/kardon
service manual
Page 8 of 109

TROUBLESHOOTING 29
ENGLISH
Troubleshooting
Track Skip or direct select with numeric
buttons, Search, Slow-motion play, repeat
play or Program play, etc., cannot be done.
• Depending on the DVD orVCD,some of the
above operations may not be available
(Playback control).
Messages do not appear on the TV screen
in the language you want.
• Select the language for Display and Preferred
Subtitle in the SETUP menu (see page 18).
For all messages from the DVD (DVD menu,
subtitles) in the proper language the disc must
have the language you selected,if not, another
language will be selected.
The audio language cannot be changed
when you play a DVD.
• Multilingual sound is not recorded on the DVD.
• Changing the language for the sound by the
Audio button on the remote or theAudio line
in the Player Menu is prohibited on the DVD.In
that case the audio language must be selected
by the main menu on the DVD.
The subtitle language cannot be changed
when you play a DVD.
• Multilingual subtitles are not recorded on the
DVD.
• Changing the language for the subtitles by the
Subtitle button on the remote or the Subtitle
line in the Player Menu is prohibited on the
DVD.In that case the subtitle language must
be selected by the main menu on the DVD.
The subtitles cannot be turned off when
you play a DVD.
• Depending on the DVD,you may not be able to
turn the subtitles off.
The angles cannot be changed when you
play a DVD.
• Multi-angles are not recorded on most DVDs.
• Change the angles when the angle mark
appears on theTV screen.
• Changing the angles is prohibited on some
DVDs.
The system does not operate properly.
• Static electricity, etc.,may affect the system’s
operation.
Disconnect theAC power cord,then connect it
again.
Please also refer to theTroubleshooting
guide contained in your loudspeaker
Owners Manual.
27820_HS500_Eng 07/08/06 14:22 Side 29
harman/kardon
service manual
Page 9 of 109

1
2
3
4
5
6
8
9
11
7
12
2
13
No.PartNo. Description
Qty.
101.00.BZ.X.W.E237 Carton boxHS300EUversion 1
01.00.BZ.X.W.E238 Carton boxHS300USversion 1
01.00.BZ.X.W.E328 Carton boxHS500EUversion 1
01.00.BZ.X.W.E329 Carton boxHS500USversion 1
2Barcordlabel 1
301.00.YS.SM1.E265 OwnermanualHS300 USversion 1
01.00.YS.SM1.E266 OwnermanualHS300 EUversion 1
01.00.YS.SM1.E356 OwnermanualHS500 USversion 1
01.00.YS.SM1.E357 OwnermanualHS500 EUversion 1
401.00.BZ.D.Z.E020 Plasticbagfor manual25*35cm 1
501.00.YS.FY3.468 Safety instruction manual HS300EU 1
01.00.YS.FY3.469 Warningcard HS300USversion 1
01.00.YS.FY3.470 Guarantee card HS300USversion 1
01.00.YS.FY3.529 Safety instruction manual HS500EU 1
01.00.YS.FY3.530 Warningcard HS500USversion 1
01.00.YS.FY3.531 Guarantee card HS500USversion 1
601.47.CNT.CTX.042 AM antennaAM-300-AWM 1
701.47.CNT.CTX.037 FM antennaFM-075 1
01.47.CNT.CTX.038 FM antennabFM-TV-75-A 1
801.47.CNT.LJX.5.012 SCART cabel 1
901.47.CNT.ACX.E052 ACpowercordEUversion 1
01.47.CNT.ACX.E053 ACpowercordUSversion 1
10CBADV-19P-19P-2M HDMI19P/MtoHDMI 19P/M CABLE 1
1101.00.RC.100 RemotecontrolHS100-RC 1
1201.00.BZ.D.H.E034 Plasticbagfor RC9*27.5cm 1
1301.14.DX.B.0007 battery7#battery 3
1401.00.BZ.D.Z.E008 Plasticbagfor battery 6*9cm 1
1501.00.BZ.X.B.E178 accessories box 1
16 accessoriesPolyfoam 2
1701.00.BZ.F.P.E100 PolyfoamHS100-left 1
01.00.BZ.F.P.E101 PolyfoamHS100-right 1
18 Main unit 1
1901.00.BZ.D.C.E065 Plasticbagfor unit 54.5*60cm 1
HS300/500 Packinginstuction
14
15
18
19
17
16
10
17
harman/kardon
service manual
Page 10 of 109

harman/kardon
service manual
Page 11 of 109

P/N Description Specification Qty Location.No. Note
01.00.WJ.TJ.E583 HS300 metals part HS300-chassis 1 HS300-PT01
01.00.WJ.TJ.E416 HS100 metals part HS100-top cover 1 HS100-PT02
01.00.WJ.TJ.E584 HS300 metals part HS300-rear panel(EU) 1 HS300-PT03 EU version
01.00.WJ.TJ.E585 HS300 metals part HS300-rear panel(US) 1 HS300-PT03 US version
01.00.WJ.TJ.E544 HS100 metals part HS100-top cover support 1 HS100-PT04
01.00.WJ.TJ.E798 HS300 metals part HS300-mainboard-top cover
support 1 HS300-PT05
01.00.WJ.TJ.E586 Heatsink 95*62*44.5MM 3 For U403 U404 U405 on
amplifer
01.00.WJ.TJ.E542 Heatsink 16*12*26MM 1 Match SQR6(BA033BCO
DIP) on SMPS Hole above PCB 18mm
01.00.WJ.TJ.E325 Heatsink 12*16*35MM 1 Match SQR5(FSDM07652R
DIP) on SMPS Hole above PCB 16mm
01.00.WJ.TJ.E730 Heatsink 16*12*46MM 1 Match SQR4(FYPF2010DN
DIP) on SMPS Hole above PCB 18mm
01.00.WJ.TJ.E673 Heatsink 41.5*13*46MM(152-DEV) 1 Match SQR3(D10XB60 DIP)
on SMPS
01.00.WJ.TJ.E674 Heatsink 50*19*46MM 1
Match
SQR1(FFPF30U20STU DIP)
on SMPS
01.00.WJ.TJ.E675 Heatsink 141*18*46MM 1
Match SQR2(IRFP460C DIP
ISL9R1560PF2 DIP) on
SMPS
01.00.WJ.TJ.E676 Heatsink 18*7*46MM(MF0948) 1
Match SQR7(FYPF2010DN
DIP KA278R05 DIP) on
SMPS
01.00.WJ.TJ.E268 Heatsink 28*28*10mm 1 Mor U4 on mainboard
01.13.L.H.E018 Magnetism annulus F5BRH 25.9*29*12.7mm 1 Important to EMI test
01.13.L.H.E020 Magnetism annulus M248 1 Important to EMI test
01.00.WJ.JG.E547 hexagonal screw M3*20.5 1 For outputboard holding on
mainboard
0100SJHS300E001 HS300 plastic part HS300front panel 1 HS300-RE01
0100SJHS100E003 HS100 plastic part HS1002 in 1 button 1 HS100-RE03
0100SJHS100E005 HS100 plastic part HS100Open/Close button
collar 1 HS100-RE05
0100SJHS100E006 HS100 plastic part HS100volume chamfer 1 HS100-RE06
HS300(B ) Component List
harman/kardon
service manual
Page 12 of 109

P/N Description Specification Qty Location.No. Note
0100SJHS100E007 HS100 plastic part HS100power indicator
lampshade 1 HS100-RE07 Transparent ABS + astigmatism liquide
0100SJHS100E008 HS100 plastic part HS100volume button
lampshade 1 HS100-RE08 Transparent ABS + astigmatism liquide
0100SJHS100E009 HS100 plastic part HS100disc tray door 1 HS100-RE09 Light black
0100SJHS100E010 HS100 plastic part HS100volume button 1 HS100-RE10
0100SJHS100E011 HS100 plastic part HS100pedestal underlay 2 HS100-RE11 Transparen PC
0100SJHS100E012 HS100 plastic part HS100len for tray
door2mm width 1 HS100-RE12
0100SJHS300E002 HS300 plastic part HS300-len for VFD3mm
width 1 HS300-RE02
0100SJ1000AE016 HS300 plastic part 1000A-IR receiver support
5.5mm 1
01.00.SJ.QT.E005 PCB plastic frame Φ7*8mm 6
01.00.FZ.QT.153 Astigmatism PVC Φ45.5*Φ9.5mm 1 Between volume button and
PCB
01.00.SJ.QT.E019 VFD filter 124.5*33.5*0.5mm 1
01.40.CON.DCZ.E178 AC power socket WS-044-0 1
01.00.SB.E035 Metal logo 47mm"Harmarn" supper
slim logo 1 Stick on the len for tray door
01.00.SB.E036 Metal logo 100mm"Harmarn" supper
slim logo 1 Stick on the top cover
01.00.SB.E054 Metal logo HS300 supper slim logo 1
01.00.YS.SM1.E265 Owner manual HS300 US version 1
01.00.YS.SM1.E266 Owner manual HS300 EU version 1
01.00.YS.TZ.T.E068 Laser label Laser precausion mark 1 Stick on the top of tray
01.00.YS.TZ.T.E057 Laser label Laser precausion guide 1 Stick on the top of tray
01.00.YS.FY3.E468 Safety instruction manual HS300-EU version 1
01.00.YS.FY3.E469 Warning card HS300-US version 1
01.00.YS.FY3.E470 Guarantee card HS300-US version 1
01.00.BZ.B.E021 MADE IN P.R.C. label 23*7MM transparent
PET(sigle side glue) 1Stick on the rear panel with
EU version EU version
01.00.RC.EHS300 Remote control HS300-RC 1
01.14.DX.B.E0007G Alkalescent battery GP7# 3
HS300(B ) Component List
harman/kardon
service manual
Page 13 of 109

P/N Description Specification Qty Location.No. Note
01.47.CNT.ACX.E052 AC power cord WS-002E+WS-019 HO5VV-
F 0.75×2C BK 2M 1 EU version
01.47.CNT.ACX.E053 AC power cord WS-002E+WS-004A
SJT18AWG×2C BK 2M 1 US version
0147CNTLJX5E012 SCART cable SCART 1 1.5M(EU version)
0147CNTLJX5E119 Grounding cable 70MM(with 42 bundles
inside) 1Connect 1820C to the
ground under loader support
Solder one and grounding
M4 another end
0147CNTLJX5E032 Grounding cable 200mm(with 42 bundles
inside) 1
Connect headphone on
1819C to ground fastened
on SMPS
Solder one and grounding
M4 another end
0147CNTLJX5E141 Grounding cable 195mm(with 42 bundles
inside 1Connect USB on 1819c to
ground fastened on SMPS
Solder one and grounding
M4 another end
01.47.CNT.CTX.E016 FM antenna FM-TV-22 1 EU version
01.47.CNT.CTX.E037 FM antenna FM-075 1 US version
01.47.CNT.CTX.E042 AM antenna AM-300-AWM 1 US version
01.15.JX.EDM3403 Loader DM3403-C(HOP-1200W)
loader (HITACHI laser) 1
01.49.E11 Tuner module TFCF1E806A 1 EU version
01.49.E07 Tuner module TFCF1E804A 1 US version
01.00.WJ.JG.E619 Screw 3*8PWBTTC (without
plumbum) 15
For SQR2 (3) SQR1(2) on
SMPS,heatsink and amplifier
(6),loader and chassis(4)
01.00.WJ.JG.E620 Screw 3*6KBTTNI (without
plumbum) 11
For front panel and
chassis(2),chassis and
pedestal underlay(9)
01.00.WJ.JG.E621 Screw 3*13PWMTTC (without
plumbum) 6 For SMPS and chassis
01.00.WJ.JG.E622 Screw 3*6PAHC (without
plumbum) 11
For 2 in 1 button and
open/close button
collar(3),1819C and front
panel(4),1820C and front
panel(4)
01.00.WJ.JG.E623 Screw 3*8KBTTNI (without
plumbum) 3For front panel and
chassis,pedestal underlay
HS300(B ) Component List
harman/kardon
service manual
Page 14 of 109

P/N Description Specification Qty Location.No. Note
01.00.WJ.JG.E101 Screw 3*8PWAHC W=7.4(without
plumbum) 2For open/close buton collar and front panel(2)
01.00.WJ.JG.E625 Screw 3*8PBTTC (without
plumbum) 12 For IC and heatsink on SMPS(12)
01.00.WJ.JG.E626 Screw 3*8PAHO (without
plumbum) 9For output port(7),tuner module(2)
01.00.WJ.JG.E626 Screw 3*8PAHO (without
plumbum) 2 For output port(2) US version
01.00.WJ.JG.E627 Screw 3*10PAHO (without
plumbum) 2For output port on
amplifier(2)
01.00.WJ.JG.E628 Screw 3*4RBTTNI (without
plumbum) 8
For rear panel and
chassis(4),top cover and
chassis(4)
01.00.WJ.JG.E629 Screw 3*6PWBTTNI W=7 (without
plumbum) 7
For top cover and chassis
with rear panel(5),top cover
support and chassis(2)
01.00.WJ.JG.E630 Screw 3*10PBTTC (without
plumbum) 1For MOS and heatsink on
SMPS
01.00.WJ.JG.E631 Screw 3*6PWMHC W=7 (without
plumbum) 9
For mainboard and
chassis(2),SMPS and
chassis(1),amplifier and
chssis(5),ESD grounding(1)
01.00.WJ.JG.E144 Screw 3*8PMHC 2
For mainboard with
mainboard-top cover support
and chassis(2)
01.00.WJ.JG.E713 Screw 3*6PMHNI 1 For mainboard and
outputboard(1)
01.00.WJ.JG.E632 Screw 3*10PMHO (without
plumbum) 3
For IC and SQR7 on
SMPS(1),and AC power
socket(2)
01.00.WJ.JG.E632 Screw 3*10PMHO (without
plumbum) 2 For SCART output port EU version
01.00.WJ.JG.E633 Nut M3 (without plumbum) 2 For SCART output port EU version
01.00.WJ.JG.E633 Nut M3 (without plumbum) 3
For IC and SQR7 on
SMPS(1),and AC power
socket(2)
01.00.WJ.JG.E634 Spring pad M3 (without plumbum) 6 For heatsink and amplifier(6)
HS300(B ) Component List
harman/kardon
service manual
Page 15 of 109

P/N Description Specification Qty Location.No. Note
01.00.WJ.JG.E635 Flat pad M3*0.5 W=8 (without
plumbum) 6For heatsink and amplifier6
01.00.BZ.X.W.E237 Carton box HS300(US version) 1 For unit and accessories US version
01.00.BZ.X.W.E238 Carton box HS300(EU version) 1 For unit and accessories EU version
01.00.BZ.X.W.E239 Big color carton box HS300(EU version) 1
According to client,for
external box and
loudspeaker
EU version
01.00.BZ.X.W.E240 Big color carton box HS300(US version) 1
According to client, for
external box and
loudspeaker
US version
01.00.BZ.X.B.E286 Accessories box HS100
380*245*45mm(V1.0) 1 For accessories EU version
01.00.BZ.X.B.E763 Accessories color box HS300(US version) 1 For accessories US version
01.00.BZ.F.P.E116 Polyfoam HS300-left 1
01.00.BZ.F.P.E117 Polyfoam HS300-right 1
01.00.BZ.F.P.E452 Polyfoam HS100-front panel 2
01.00.BZ.D.H.E053 Plastic bag for unit 54.5*60cm 1 For unit
01.00.BZ.D.Z.E020 Plastic bag for user's
manual 25*35cm 1 For owner manual
01.00.BZ.D.Z.E034 Plastic bag for remote
control 9*27.5CM 1 For remote control
01.00.BZ.D.Z.E008 Plastic bag for battery 6*9cm 1 For battery
01.00.BZ.D.H.E002 Plastic bag 11*28cm 1 For AC power cord
01.00.FZ.QT.E187 Mask PVC Φ38.5 (bottom with
glue)black PVC 1Stick inside the volume
button
0147CNTLJX7E026 Connect cable 2.0-5Y-5Y-260mm-
B(UL20080 28AWG) 1Connect loader and CN1 on
mainboard
0147CNTLJX7E125 Connect cable 2.0-6Y-6Y-350mm-
B(UL20080 28AWG) 1Connect loader and CN2 on
mainboard
0147CNTLJX7E357 Connect cable 2.0-7Y-7Y-220MM -A 1 Connect CN606 on 1819C
and CN607 on 1822C
0147CNTLJX7E539 Connect cable 2.54-2.0-6Y-330mm-B 1 Connect CN503 on SMPS
and CN602 on 1819C B
HS300(B ) Component List
harman/kardon
service manual
Page 16 of 109

P/N Description Specification Qty Location.No. Note
0147CNTLJX7E358 Connect cable 2.54-2.0-4Y-210mm-A 1
Connect CN508 on SMPS
and CN14 on
mainboardM
0147CNTLJX7E054 Connect cable 2.0-10Y-10Y-70mm-A 1
Connect CN9 on mainboard
L and CN303 on output
boardL
0147CNTLJX7E312 Connect cable 2.54-2.0-13Y-120mm-B 1 Connect CN509 on SMPS
and CN5 on mainboard (K)
0147CNTLJX7E180 Connect cable 2.54-2.0-5Y-80mm-B 1 Connect CN505 on SMPS
and CN402 on amplifier (I)
0147CNTLJX7E420 Connect cable VH-3Y-2Y-2Y-610mm-
A(with magnetism annulus) 1Connect CN506 on SMPS
and CN403 on amplifierJ
cable wrap magnetism
annulus in one circuit,and
the length from magnetism
annulus to another end is
120mmone cable length
610mmanother 300mm
0147CNTLJX7E401 Connect cable VH-3Y-2Y-330mm-B(with
magnetism annulus) 1Connect power socket and
SMPS
140mm from magnetism
annulus to another solder
end
0147CNTLJX7E361 Connect cable 2.0-4Y-4Y-580MM-Awith
shield 1
Connect CN605 on
1819C(F) and CN304 on
outputboardF
0147CNTLJX7E402 Connect cable
2.0-5Y-5Y-480MM-
Ared,black,white,black
shield,green
1
Connect CN603 on 1819C
(Hand CN6 on
mainboardH(with shield
order on mainboard from
fist pin:red,black,white,black
shield,green)
0147CNTLJX7E052 Connect cable 2.0-9Y-9Y-70mm-A 1 Connect CN609 on 1820C
(E) and CN611 on 1819C (E)
0147CNTLJX7E163 HDMI cable CBADV-19P-19P-
2M(black,φ5.5 ,30AWG) 1
01.48.BPX.1.E109 Flat cable 1.0*20P*60mmA 1
Connect CN11 on
mainboard (O) and CN302
on mainboardO
01.48.BPX.1.E108 Flat cable 1.0*14P*60mmA 1
Connect CN13 on
mainboard (N) and CN301on
outputboard (N)
HS300(B ) Component List
harman/kardon
service manual
Page 17 of 109

P/N Description Specification Qty Location.No. Note
01.48.BPX.1.E107 Flat cable 1.25*18P*380mmA 1
Connect CN601 on 1819C
(A) and CN4 on mainboard
(A)
01.48.BPX.1.E103 Flat cable 1.0*16P*70mmA 1
Connect CN7 on mainboard
(C) and CN401 on amplifier
(C)
01.48.BPX.1.E085 Flat cable 1.25*11P*70mmA 1 Connect tuner module and
CN12 on mainboard
01.48.BPX.2.E159 Flat cable 0.5*24P*290mmA 1 Connect loader and CN3 on
mainboard
01.00.DP.XJ.E192 Silica gel underlay 50.6*4.2*1.5mm(sigle side
with 500# white glue) 4 HS100-H01 For underlay
01.00.DP.XJ.E199 Silica gel underlay 21*16*1.0mm (φ3.0)black 1 Match D504(ISL9R1560PF2
DIP) on SMPS
01.00.DP.HM.E199 Sponge 20*20*7MM(with double
side glue) 3For VFD (2),flat cable
attached to volumeboard(1)
01.00.DP.JY.E158 Insulated PVC 150*152*0.5mm 1 Place between SMPS and
chassis
01.00.DP.JY.E149 Insulated PVC
80*55*0.5MM
transparence PVC with
sigle side glue
1Stick on the top cover
support
01.00.DP.JY.E173 Insulated PVC 150*160*0.5mm( with sigle
side glue) 1Stick under the top cover
above SMPS
01.00.DP.JY.E174 Insulated PVC 38*55*0.5mm( with sigle
side glue) 1Stick under output board
above mainboard
01.00.DP.JY.E124 Insulated particle TO-220 1 For D504(ISL9R1560PF2
DIP) on SMPS
01.00.DP.HM.E290 Sponge 20*20*8mm(with sigle side
glue) 4Place under big transfer and
heatsink on SMPS
01.00.DP.HM.E316 Sponge 20*20*6MM(with sigle side
glue 1Place under transfer on
SMPS
01.00.DP.HM.E317 Soft sponge 50*12*4MM(with sigle side
glue 4
Stick on top cover
support(2),mainboard-top
cover support on
mainboard(2)
01.00.DP.HM.E312 Sponge 125*20*2MM(with sigle side
glue 1Stick on chassis for flat
cable of loader
HS300(B ) Component List
harman/kardon
service manual
Page 18 of 109

P/N Description Specification Qty Location.No. Note
01.00.DP.HM.E313 Sponge 65*20*2MM(with sigle side
glue 1Stick on chassis for flat cable of loader
01.00.DP.HM.E314 Sponge 30*15*4MM(with sigle side
glue 1For magnetism annulus of AC power cord
01.00.DP.HM.E289 Sponge 10*10*6MM(with double
side glue) 1 For IR receiver
01.00.DP.HM.E263 Sponge 20*10*8MM(with double
side glue) 1Place flank between tuner
module and chassis
01.00.DP.HM.E160 Sponge 20*10*4.5mm(with sigle
side glue) 3Place between amplifer and
heatsink
01.00.DP.HM.E117 Sponge 20*10*5MM(with double
side glue) 1Place between 1820C and
Flat cable 3M9448
01.00.FZ.QT.E122 Plastic fastener 12CM 4
01.00.FZ.QT.E216 Plastic fastener 20CM 2
01.00.DP.QT.E001 Sil-pad sil-pad 400-2820 3 For Q501 Q503 Q504 on
SMPS
01.00.DP.JY.E112 Diathermanous Selenium
Rubber 16*11*1mm 3 Place on U403 U404 U405
on amplifier
01.00.DD.PM.E092 Sponge with electric
material 10*9*10mm 3 Place under amplifier
01.00.DD.PM.E166 Sponge with electric
material 110*10*8mm 1 Place on top cover support
01.00.DD.QT.E152 Electric cloth 20*10MMsigle side 1 Stick between s-video out
side and rear panel
0211HAV06M3625C01 Mainboard(semi-
manufactured goods)
HAV06M-3625C01(US
Version +HITACHI laser) 1 Four layers board
0211HAV06M3625C02 Mainboard(semi-
manufactured goods)
HAV06M-3625C02(EU
Version +HITACHI laser) 1 Four layers board
0214HAV06I1804C01 Outputboard(semi-
manufactured goods)
HAV06I-1804C01(US
version) 1 Two layers board
0214HAV06I1804C02 Outputboard(semi-
manufactured goods)
HAV06I-1804C02(EU
version) 1 Two layers board
0217HAV06A1805C02 Amplifier(semi-
manufactured goods) HAV06A-1805C02 1 Two layers board
0219HAV06P1806C02 SMPS(semi-manufactured
goods) HAV06P-1806C02 1 Two layers board
HS300(B ) Component List
harman/kardon
service manual
Page 19 of 109

P/N Description Specification Qty Location.No. Note
0215HAV06K1819C01 Front panel board(semi-
manufactured goods) HAV06K-1819C01 1 Two layers board
0215HAV06K1820C01 Front panel board(semi-
manufactured goods) HAV06K-1820C01 1 Two layers board
0215HAV06K1822C01 Front panel board(semi-
manufactured goods) HAV06K-1822C01 1 Two layers board
P/N Description Specification Qty Location.No. Note
01.00.WJ.TJ.E583 HS300 metals part HS300-chassis 1 HS300-PT01
01.00.WJ.TJ.E416 HS100 metals part HS100-top cover 1 HS100-PT02
01.00.WJ.TJ.E683 HS500 metals part HS500-rear panel(EU)) 1 HS500-PT03 EU version
01.00.WJ.TJ.E684 HS500 metals part HS500-rear panel(US) 1 HS500-PT03 US version
01.00.WJ.TJ.E544 HS100 metals part HS100-top cover support 1 HS100-PT04
01.00.WJ.TJ.E798 HS300 metals part HS300-mainboard-top cover
support 1 HS300-PT05
01.00.WJ.TJ.E586 Heatsink 95*62*44.5MM 3 for U403 U404 U405 on
amplifer
01.00.WJ.TJ.E542 Heatsink 16*12*26MM 1 match SQR6(BA033BCO
DIP) on SMPS Hole above PCB 18mm
01.00.WJ.TJ.E325 Heatsink 12*16*35MM 1 match SQR5(FSDM07652R
DIP) on SMPS Hole above PCB 16mm
01.00.WJ.TJ.E730 Heatsink 16*12*46MM 1 match SQR4(FYPF2010DN
DIP) on SMPS Hole above PCB 18mm
01.00.WJ.TJ.E673 Heatsink 41.5*13*46MM(152-DEV) 1 match SQR3(D10XB60 DIP)
on SMPS
01.00.WJ.TJ.E674 Heatsink 50*19*46MM 1
match
SQR1(FFPF30U20STU DIP)
on SMPS
01.00.WJ.TJ.E675 Heatsink 141*18*46MM 1
match SQR2(IRFP460C DIP
ISL9R1560PF2 DIP) on
SMPS
01.00.WJ.TJ.E676 Heatsink 18*7*46MM(MF0948) 1
match SQR7(FYPF2010DN
DIP KA278R05 DIP) on
SMPS
01.00.WJ.TJ.E268 Heatsink 28*28*10mm 1 for U4 on mainboard
HS300(B ) Component List
HS500(B) Component List
harman/kardon
service manual
Page 20 of 109